Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU) › from 2015.10
RM3090E _57 Power Source / Network _008434 NETWORKING _0221948 CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU)  Certification ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptoms Trouble Area
Certification ECU Communication Stop Mode Either condition is met:
·

"Certification (Smart)" is not displayed on "CAN Bus Check".

(Click here)

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Certification ECU Communication Stop Mode" in "DTC Combination Table".

(Click here)


·

Power source or inside certification ECU (smart key ECU assembly)

·

Certification ECU (smart key ECU assembly) CAN branch wire or connector

·

Certification ECU (smart key ECU assembly)



WIRING DIAGRAM

C262771E05
5.615,4.354 6.208,4.531 0.594,0.177 10 false E 5.083,5.083 6.927,5.427 1.844,0.344 10 false Certification ECU (Smart Key ECU Assembly) 5.615,3.75 6.208,3.927 0.594,0.177 10 false IG 5.615,3.156 6.208,3.333 0.594,0.177 10 false CUTB 5.604,2.406 6.198,2.583 0.594,0.177 10 false +B 5.208,4.344 5.802,4.521 0.594,0.177 10 false G82 5.208,2.406 5.802,2.583 0.594,0.177 10 false G82 5.208,3.125 5.802,3.302 0.594,0.177 10 false G82 5.208,3.708 5.802,3.885 0.594,0.177 10 false G84 5.615,0.656 6.208,0.833 0.594,0.177 10 false CANH 5.635,1.146 6.229,1.323 0.594,0.177 10 false CANL 5.208,1.146 5.802,1.323 0.594,0.177 10 false G84 5.208,0.656 5.802,0.833 0.594,0.177 10 false G84 1.688,0.531 2.198,0.938 0.51,0.406 10 false 5 1.667,1.021 2.063,1.354 0.396,0.333 10 false 16 0.188,1.5 0.917,1.948 0.729,0.448 10 false G189 0.198,1.667 2.323,2.104 2.125,0.438 10 false No. 7 CAN Junction Connector 1.917,2.417 4.333,2.667 2.417,0.25 10 false from Battery 1.917,3.125 4.333,3.375 2.417,0.25 10 false from Battery 1.813,3.719 4.229,3.969 2.417,0.25 10 false from IG2 Relay 3.75,2.25 4.167,2.417 0.417,0.167 10 false AM2 3.5,2.917 4.333,3.083 0.833,0.167 10 false ECU-B NO.1 3.75,3.5 4.083,3.667 0.333,0.167 10 false IGN 5.24,0.448 5.833,0.625 0.594,0.177 10 false 14 5.26,0.938 5.854,1.115 0.594,0.177 10 false 15 5.281,2.177 5.875,2.354 0.594,0.177 10 false 2 5.26,2.896 5.854,3.073 0.594,0.177 10 false 10 5.292,3.49 5.885,3.667 0.594,0.177 10 false 5 5.26,4.135 5.854,4.313 0.594,0.177 10 false 11

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

DTC check procedure: Turn the ignition switch to ON and wait at least 20 seconds.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU)>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (CERTIFICATION ECU CAN BRANCH WIRE)
a.
C277454C01
1.385,0.26 1.865,0.563 0.479,0.302 2.083,1.271 2.438,1.938 2.438,1.938 2.646,1.938 true 1.948,1.271 1.729,1.938 1.729,1.938 1.552,1.938 true 0.073,0.052 0.385,0.208 0.313,0.156 10 *a 1.49,0.344 1.802,0.5 0.313,0.156 10 G84 1.135,1.865 1.594,2.021 0.458,0.156 10 CANH 2.677,1.854 3.135,2.01 0.458,0.156 10 CANL
*a Front view of wire harness connector
(to Certification ECU [Smart Key ECU Assembly])


Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G84-14 (CANH) - G84-15 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE CERTIFICATION ECU CAN BRANCH WIRE OR CONNECTOR (CANH, CANL)

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - BATTERY AND BODY GROUND)
a.
C277455C01
0.115,2.396 0.521,2.677 0.406,0.281 0.292,0.677 0.698,0.958 0.406,0.281 0.771,1.406 0.99,1.406 0.99,1.406 1.135,1.083 true 2.802,1.25 2.49,1.25 2.49,1.25 2.292,0.969 true 2.292,0.781 2.542,0.552 2.542,0.552 2.75,0.552 true 2.781,2.052 2.594,2.052 2.594,2.052 2.417,2.354 true 0.052,0.031 0.365,0.188 0.313,0.156 10 *a 0.354,0.74 0.667,0.896 0.313,0.156 10 G82 0.177,2.448 0.49,2.604 0.313,0.156 10 G84 0.615,1.323 0.927,1.479 0.313,0.156 10 E 2.802,0.469 3.115,0.625 0.313,0.156 10 +B 2.844,1.167 3.271,1.333 0.427,0.167 10 CUTB 2.813,1.979 3.052,2.156 0.24,0.177 10 IG
*a Front view of wire harness connector
(to Certification ECU [Smart Key ECU Assembly])


Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



b.

Disconnect the certification ECU (smart key ECU assembly) connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G82-2 (+B) - Body ground Always 11 to 14 V
G82-10 (CUTB) - Body ground Always 11 to 14 V
G84-5 (IG) - Body ground Ignition switch ON 11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G82-11 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR