Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU) › from 2015.10
RM3090E _57 Power Source / Network _008434 NETWORKING _0221948 CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU)  Check Bus 3 Line for Short to +B  


DESCRIPTION

There may be a short circuit between one of the CAN bus lines and +B when no resistance exists between terminal 6 (CA3H) of the central gateway ECU and terminal 16 (BAT) of the DLC3, or terminal 21 (CA3L) of the central gateway ECU and terminal 16 (BAT) of the DLC3.

Detection Item Trouble Area

*1: w/ Navigation System

*2: w/ Audio and Visual System (for Radio and Display Type)

No resistance exists between terminal 6 (CA3H) of the central gateway ECU and terminal 16 (BAT) of the DLC3, or terminal 21 (CA3L) of the central gateway ECU and terminal 16 (BAT) of the DLC3.
·

Short to +B in bus 3 CAN main wires

·

Short to +B in bus 3 CAN branch wires

·

Central gateway ECU

·

Navigation receiver assembly*1

·

Radio and display receiver assembly*2

·

No. 8 CAN junction connector



WIRING DIAGRAM

C334603E03
6.083,0.698 6.563,0.885 0.479,0.188 10 false CA3H 6.115,1.427 6.594,1.615 0.479,0.188 10 false CA3L 6.115,4.365 6.594,4.552 0.479,0.188 10 false CAYH 6.115,5.146 6.594,5.333 0.479,0.188 10 false CAYL 5.823,0.688 5.979,0.885 0.156,0.198 10 false 6 5.76,1.135 5.99,1.375 0.229,0.24 10 false 21 5.771,4.354 6,4.594 0.229,0.24 10 false 19 5.771,4.833 6,5.073 0.229,0.24 10 false 20 4.5,0.677 4.656,0.875 0.156,0.198 10 false 3 4.49,1.125 4.719,1.365 0.229,0.24 10 false 14 4.521,4.396 4.677,4.594 0.156,0.198 10 false 4 4.49,4.823 4.719,5.063 0.229,0.24 10 false 15 3.052,1.479 3.208,1.677 0.156,0.198 10 false 1 2.99,1.99 3.219,2.229 0.229,0.24 10 false 12 1.719,1.49 1.875,1.688 0.156,0.198 10 false 9 1.688,1.958 1.917,2.198 0.229,0.24 10 false 10 1.135,1.635 1.615,1.823 0.479,0.188 10 false CANH 1.156,2.167 1.635,2.354 0.479,0.188 10 false CANL 5.583,5.51 6.052,5.854 0.469,0.344 10 false G170 5.594,5.698 7.031,5.979 1.438,0.281 10 false Central Gateway ECU 2.823,5.719 4.823,5.99 2,0.271 10 false No. 8 CAN Junction Connector 2.813,5.531 3.313,5.844 0.5,0.313 10 false G173 0.104,2.594 1.573,2.906 1.469,0.313 10 false G139*1, G143*2 0.104,2.771 2.771,3.167 2.667,0.396 10 false Navigation Receiver Assembly*1, Radio and Display Receiver Assembly*2 0.135,4.635 2.135,4.906 2,0.271 10 false *1: w/ Navigation System 0.156,5.156 2.115,5.583 1.958,0.427 10 false *2: w/ Audio and Visual System (for Radio and Display Type)

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU)>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 8 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) battery terminal.

C312658C57
1.844,0.51 2.406,0.792 0.563,0.281 5.594,0.594 6.156,0.875 0.563,0.281 6.042,2.406 6.208,2.406 6.208,2.406 6.479,1.781 true 1.406,1.51 1.177,1.25 1.177,1.25 0.927,1.25 true 1.417,1.719 1.177,1.938 1.177,1.938 0.927,1.938 true 1.74,1.51 1.177,0.948 1.177,0.948 0.927,0.948 true 1.708,1.708 1.219,2.177 1.219,2.177 0.969,2.177 true 1.885,1.5 1.177,0.677 1.177,0.677 0.927,0.677 true 1.885,1.719 1.198,2.49 1.198,2.49 0.948,2.49 true 0.188,0.104 0.5,0.302 0.313,0.198 10 false *a 4.479,0.115 4.792,0.313 0.313,0.198 10 false *b 5.698,2.344 6.042,2.542 0.344,0.198 10 false BAT 0.365,1.844 0.927,2.052 0.563,0.208 10 false CANL*c 0.354,1.167 0.927,1.365 0.573,0.198 10 false CANH*c 0.354,0.594 0.917,0.792 0.563,0.198 10 false CANH*d 0.396,2.417 0.948,2.615 0.552,0.198 10 false CANL*d 1.948,0.563 2.635,0.948 0.688,0.385 10 false G173 5.76,0.646 6.375,0.844 0.615,0.198 10 false G14 0.354,0.854 0.917,1.063 0.563,0.208 10 false CANH*d 0.396,2.104 0.948,2.302 0.552,0.198 10 false CANL*d
*a Front view of wire harness connector
(to No. 8 CAN Junction Connector)
*b Front view of DLC3
*c
·

to Navigation Receiver Assembly (w/ Navigation System)

·

to Radio and Display Receiver Assembly (w/ Audio and Visual System [for Radio and Display Type])


*d to Central Gateway ECU



b.

Disconnect the No. 8 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connect to

*1: w/ Navigation System

*2: w/ Audio and Visual System (for Radio and Display Type)

G173-1 (CANH) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
·

Navigation receiver assembly*1

·

Radio and display receiver assembly*2


G173-12 (CANL) - G14-16 (BAT)
G173-3 (CANH) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Central gateway ECU
G173-14 (CANL) - G14-16 (BAT)
G173-4 (CANH) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Central gateway ECU
G173-15 (CANL) - G14-16 (BAT)



Result:
Proceed to
OK A
NG (Central gateway ECU CAN main wire) B
NG (ECU or sensor CAN branch wires) C



A

REPLACE NO. 8 CAN JUNCTION CONNECTOR

B

2.CONNECT CONNECTOR

C

4.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (ECU, SENSOR)
2.CONNECT CONNECTOR
a.

Reconnect the G173 No. 8 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

3.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (CENTRAL GATEWAY ECU)
3.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (CENTRAL GATEWAY ECU)
a.
C338146C24
1.458,2.573 1.979,2.802 0.521,0.229 1.438,0.417 1.948,0.635 0.51,0.219 2.708,0.646 2.521,0.646 2.521,0.646 2.271,1.26 true 2.781,2.198 2.594,2.198 2.594,2.198 2.188,1.49 true 2.844,4.021 2.656,4.021 2.656,4.021 2.354,3.698 true 1.333,2.156 1.51,2.156 1.51,2.156 1.917,1.521 true 1.573,2.354 1.75,2.354 1.75,2.354 2.052,1.531 true 0.094,0.208 0.406,0.365 0.313,0.156 10 false *a 0.135,2.49 0.448,2.646 0.313,0.156 10 false *b 1.583,2.604 1.938,2.792 0.354,0.188 10 false G14 1.531,0.427 2.052,0.677 0.521,0.25 10 false G170 2.896,3.896 3.427,4.146 0.531,0.25 10 false BAT 2.76,0.531 3.292,0.781 0.531,0.25 10 false CA3H 2.823,2.083 3.354,2.333 0.531,0.25 10 false CA3L 0.896,2.073 1.354,2.292 0.458,0.219 10 false CAYH 1.167,2.281 1.573,2.5 0.406,0.219 10 false CAYL
*a Front view of wire harness connector
(to Central Gateway ECU)
*b Front view of DLC3


Disconnect the central gateway ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G170-6 (CA3H) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G170-21 (CA3L) - G14-16 (BAT)
G170-19 (CAYH) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G170-20 (CAYL) - G14-16 (BAT)



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (CENTRAL GATEWAY ECU - NO. 8 CAN JUNCTION CONNECTOR)

4.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (ECU, SENSOR)
a.
C334464C39
1.5,0.323 1.938,0.542 0.438,0.219 1.469,2.5 1.906,2.719 0.438,0.219 0.781,0.531 0.948,0.531 0.948,0.531 1.375,1.021 true 0.865,1.823 1.031,1.823 1.031,1.823 1.427,1.135 true 2.354,3.625 2.615,3.99 2.615,3.99 2.792,3.99 true 0.083,0.125 0.396,0.281 0.313,0.156 10 false *a 0.115,2.5 0.427,2.656 0.313,0.156 10 false *b 1.563,2.521 1.875,2.677 0.313,0.156 10 false G14 1.552,0.333 2.01,0.594 0.458,0.26 10 false G170 2.833,3.896 3.146,4.052 0.313,0.156 10 false BAT 0.406,0.438 0.896,0.625 0.49,0.188 10 false CA3H 0.479,1.719 0.969,1.906 0.49,0.188 10 false CA3L
*a Component with harness connected
(Central Gateway ECU)
*b Front view of DLC3


Reconnect the CAN junction connector.


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the bus line shorted to +B is connected.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G170-6 (CA3H) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G170-21 (CA3L) - G14-16 (BAT)


HINT:

If the resistance changes to 6 kΩ or higher when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.



Result:
Proceed to
OK
NG



OK

REPLACE CORRESPONDING ECU OR SENSOR

NG

REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR CAN BRANCH WIRES OR CONNECTOR