Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU) › from 2015.10
RM3090E _57 Power Source / Network _008434 NETWORKING _0221948 CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU)  Open in Bus 5 Main Bus Line  


DESCRIPTION

There may be an open circuit in one of the bus 5 CAN main wires when the resistance between terminals 15 (CA5H) and 16 (CA5L) of the central gateway ECU is 70 Ω or higher.

Symptom Trouble Area
Resistance between terminals 15 (CA5H) and 16 (CA5L) of central gateway ECU is 70 Ω or higher.
·

CAN main wire or connector

·

Central gateway ECU

·

No. 9 CAN junction connector

·

No. 10 CAN junction connector



This malfunction is not related to the lines of a bus 5 branch or to ECUs or sensors connected to a bus 5 branch.

WIRING DIAGRAM

C334604E02
5.667,0.302 6.125,0.49 0.458,0.188 10 false CA5H 5.667,1.01 6.125,1.198 0.458,0.188 10 false CA5L 5.667,2.313 6.125,2.5 0.458,0.188 10 false CAXH 5.688,3.052 6.146,3.24 0.458,0.188 10 false CAXL 5.365,0.281 5.573,0.479 0.208,0.198 10 false 15 5.365,0.76 5.573,0.958 0.208,0.198 10 false 16 5.365,2.771 5.573,2.969 0.208,0.198 10 false 24 4.167,2.771 4.375,2.969 0.208,0.198 10 false 12 2.917,2.771 3.125,2.969 0.208,0.198 10 false 13 1.781,2.76 1.99,2.958 0.208,0.198 10 false 15 1.781,0.76 1.99,0.958 0.208,0.198 10 false 14 1.823,0.281 1.99,0.479 0.167,0.198 10 false 4 1.823,2.292 1.99,2.49 0.167,0.198 10 false 5 2.948,2.292 3.115,2.49 0.167,0.198 10 false 3 4.177,2.292 4.344,2.49 0.167,0.198 10 false 2 5.385,2.302 5.552,2.5 0.167,0.198 10 false 9 0.146,3.219 0.615,3.5 0.469,0.281 10 false G174 2.646,3.198 3.063,3.417 0.417,0.219 10 false N36 5.219,3.438 5.719,3.823 0.5,0.385 10 false G170 0.146,3.385 2.229,3.615 2.083,0.229 10 false No. 9 CAN Junction Connector 2.646,3.375 4.802,3.688 2.156,0.313 10 false No. 10 CAN Junction Connector 5.229,3.594 6.667,3.896 1.438,0.302 10 false Central Gateway ECU

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU)>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (NO. 9 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) battery terminal.

C343209C17
3.333,0.198 3.833,0.448 0.5,0.25 2.625,0.26 2.813,0.26 2.813,0.26 3.385,0.854 true 2.583,1.604 2.771,1.604 2.771,1.604 3.417,1.031 true 2.375,0.469 2.563,0.469 2.563,0.469 3.188,0.854 true 2.417,1.365 2.604,1.365 2.604,1.365 3.229,1.01 true 0.135,0.094 0.448,0.292 0.313,0.198 10 false *a 2.052,0.177 2.625,0.385 0.573,0.208 10 false CANH*c 2.031,1.521 2.594,1.729 0.563,0.208 10 false CANL*c 3.417,0.229 3.958,0.615 0.542,0.385 10 false G174 1.792,0.385 2.365,0.594 0.573,0.208 10 false CANH*b 1.854,1.271 2.417,1.479 0.563,0.208 10 false CANL*b
*a Front view of wire harness connector
(to No. 9 CAN Junction Connector)
*b to Central Gateway ECU
*c to No. 10 CAN Junction Connector - -



b.

Disconnect the No. 9 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G174-4 (CANH) - G174-14 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω
G174-5 (CANH) - G174-15 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result Proceed to
OK A
NG (No. 10 CAN junction connector CAN main wire) B
NG (Central gateway ECU CAN main wire) C



A

REPLACE NO. 9 CAN JUNCTION CONNECTOR

B

2.CONNECT CONNECTOR

C

6.CONNECT CONNECTOR
2.CONNECT CONNECTOR
a.

Reconnect the G174 No. 9 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

3.CHECK FOR OPEN IN CAN BUS WIRE (NO. 10 CAN JUNCTION CONNECTOR)
3.CHECK FOR OPEN IN CAN BUS WIRE (NO. 10 CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 10 CAN junction connector.

C343209C18
1.823,0.792 2.323,1.042 0.5,0.25 2.417,0.26 2.604,0.26 2.604,0.26 2.813,0.865 true 2.344,1.573 2.531,1.573 2.531,1.573 2.823,1.021 true 3.521,1.531 3.365,1.531 3.365,1.531 3.083,1.01 true 3.667,0.271 3.479,0.271 3.479,0.271 3.083,0.844 true 0.135,0.094 0.448,0.292 0.313,0.198 10 false *a 1.854,0.177 2.438,0.406 0.583,0.229 10 false CANH*b 3.729,0.198 4.344,0.406 0.615,0.208 10 false CANH*c 1.771,1.5 2.344,1.719 0.573,0.219 10 false CANL*b 3.573,1.448 4.188,1.656 0.615,0.208 10 false CANL*c 1.938,0.823 2.458,1.146 0.521,0.323 10 false N36
*a Front view of wire harness connector
(to No. 10 CAN Junction Connector)
*b to Central Gateway ECU
*c to No. 9 CAN Junction Connector - -



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N36-2 (CANH) - N36-12 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω
N36-3 (CANH) - N36-13 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result Proceed to
OK A
NG (No. 9 CAN junction connector CAN main wire) B
NG (Central gateway ECU CAN main wire) C



A

REPLACE NO. 10 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 10 CAN JUNCTION CONNECTOR - NO. 9 CAN JUNCTION CONNECTOR)

C

4.CONNECT CONNECTOR
4.CONNECT CONNECTOR
a.

Reconnect the N36 No. 10 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

5.CHECK FOR OPEN IN CAN BUS WIRE (CENTRAL GATEWAY ECU)
5.CHECK FOR OPEN IN CAN BUS WIRE (CENTRAL GATEWAY ECU)
a.
C326490C28
1.5,0.167 2.031,0.385 0.531,0.219 1.688,1.854 1.885,1.854 1.885,1.854 2.74,1 true 2.438,2.042 2.635,2.042 2.635,2.042 2.865,1.208 true 0.135,0.094 0.438,0.427 0.302,0.333 10 false *a 1.583,0.198 2.188,0.5 0.604,0.302 10 false G170 1.25,1.771 1.688,1.938 0.438,0.167 10 false CAXH 2.01,1.969 2.427,2.135 0.417,0.167 10 false CAXL
*a Front view of wire harness connector
(to Central Gateway ECU)


Disconnect the central gateway ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G170-9 (CAXH) - G170-24 (CAXL) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (CENTRAL GATEWAY ECU - NO. 10 CAN JUNCTION CONNECTOR)

6.CONNECT CONNECTOR
a.

Reconnect the G174 No. 9 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

7.CHECK FOR OPEN IN CAN BUS WIRE (CENTRAL GATEWAY ECU)
7.CHECK FOR OPEN IN CAN BUS WIRE (CENTRAL GATEWAY ECU)
a.
C326490C29
1.5,0.167 2.031,0.385 0.531,0.219 0.646,1.802 0.844,1.802 0.844,1.802 1.344,1.198 true 0.75,2.042 0.948,2.042 0.948,2.042 1.51,1.208 true 0.135,0.094 0.438,0.427 0.302,0.333 10 false *a 1.583,0.198 2.188,0.5 0.604,0.302 10 false G170 0.219,1.729 0.656,1.896 0.438,0.167 10 false CA5H 0.354,1.969 0.792,2.135 0.438,0.167 10 false CA5L
*a Front view of wire harness connector
(to Central Gateway ECU)


Disconnect the central gateway ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G170-15 (CA5H) - G170-16 (CA5L) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (CENTRAL GATEWAY ECU - NO. 9 CAN JUNCTION CONNECTOR)