Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM(for Radio and Display Type) › from 2015.10
RM3090E _56 Audio / Visual / Telematics _008776 NAVIGATION / MULTI INFO DISPLAY _0148247 NAVIGATION SYSTEM(for Radio and Display Type) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Radio and Display Type)  Radio Broadcast cannot be Received or Poor Reception  


WIRING DIAGRAM

E337728E01
0.073,1.26 1.021,1.844 0.948,0.583 10 false Satellite Radio Antenna Assembly*2 0.083,0.354 1.031,0.938 0.948,0.583 10 false No.1 Amplifier Antenna Assembly*1 3.51,1.729 4.792,2.104 1.281,0.375 10 false No. 2 Antenna Cord Sub-assembly 2.208,1.729 3.458,2.135 1.25,0.406 10 false No. 3 Antenna Cord Sub-assembly 4.854,1.729 5.823,2.135 0.969,0.406 10 false Antenna Cord Sub-assembly 2.385,0.708 2.542,0.906 0.156,0.198 10 false 5 2.396,0.99 2.625,1.198 0.229,0.208 10 false 5-a 2.927,0.979 3.156,1.188 0.229,0.208 10 false 2-a 3.708,0.99 3.938,1.198 0.229,0.208 10 false 2-a 4.167,0.99 4.396,1.198 0.229,0.208 10 false 1-a 4.948,0.99 5.177,1.198 0.229,0.208 10 false 1-a 5.427,0.99 5.656,1.198 0.229,0.208 10 false 1-a 3.021,0.719 3.177,0.917 0.156,0.198 10 false 2 3.708,0.708 3.865,0.906 0.156,0.198 10 false 2 4.292,0.708 4.448,0.906 0.156,0.198 10 false 1 4.958,0.719 5.115,0.917 0.156,0.198 10 false 1 5.531,0.719 5.688,0.917 0.156,0.198 10 false 1 6.042,2.396 7.083,2.625 1.042,0.229 10 false Navigation ECU 0.125,2.438 3.635,2.885 3.51,0.448 10 false *1: Except models with the vehicle identification number on the certification label ending with the character X 0.135,3.063 3.646,3.51 3.51,0.448 10 false *2: Only for models with the vehicle identification number on the certification label ending with the character X

CAUTION / NOTICE / HINT

NOTICE:

Check that the wire harness is properly installed and does not have any sharp bends, pinching or loose connections.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING


PROCEDURE

1.CHECK IF RADIO AUTO-SEARCH FUNCTIONS PROPERLY
a.

Check the radio automatic station search function by activating it.

OK:

Automatic station search function stops on a station.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK OPTIONAL COMPONENTS
2.CHECK OPTIONAL COMPONENTS
a.

Check if any optional components that may decrease reception capacity, such as sunshade film or a telephone antenna, are installed.

OK:

Optional components are installed.


NOTICE:

Do not remove optional components without permission of the customer.



Result:
Proceed to
OK
NG



OK

REMOVE OPTIONAL COMPONENTS AND CHECK AGAIN (SEE NOTICE ABOVE)

NG

3.CHECK RADIO & DISPLAY RECEIVER ASSEMBLY (ANTENNA)
3.CHECK RADIO & DISPLAY RECEIVER ASSEMBLY (ANTENNA)
a.
E276819

Remove the antenna connector from the radio and display receiver assembly.


b.

Turn the ignition switch to ACC with the radio and display receiver assembly connector connected.


c.

Turn on the radio and turn into AM mode.


d.

Place a screwdriver, thin wire or other metal object on the radio and display receiver assembly antenna jack and check that noise can be heard from the speakers.

OK:

Noise occurs.



Result:
Proceed to
OK
NG



OK

4.INSPECT RADIO & DISPLAY RECEIVER ASSEMBLY

NG

REPLACE RADIO & DISPLAY RECEIVER ASSEMBLY

4.INSPECT RADIO & DISPLAY RECEIVER ASSEMBLY
a.

Disconnect the RA radio and display receiver assembly connector.


b.
E277921E01
1.063,0.781 1.281,0.781 1.281,0.781 1.531,1.042 true 2.333,0.635 2.083,0.635 2.083,0.635 1.833,0.885 true 2.354,1.583 2.104,1.583 2.104,1.583 1.833,1.271 true 0.677,0.698 1.208,0.885 0.531,0.188 10 false ANT+ 2.375,0.552 2.906,0.74 0.531,0.188 10 false 2 2.396,1.5 2.927,1.688 0.531,0.188 10 false 4

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
5 (ANT+) - Body ground Ignition switch ACC, radio switch on and FM or AM selected 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK VEHICLE CONDITION

NG

REPLACE RADIO & DISPLAY RECEIVER ASSEMBLY

5.CHECK VEHICLE CONDITION
a.

Check the vehicle condition.


Result:
Result Proceed to
Except models with the vehicle identification number on the certification label ending with the character X A
Only for models with the vehicle identification number on the certification label ending with the character X B



A

6.CHECK NO. 3 ANTENNA CORD SUB-ASSEMBLY

B

10.CHECK NO. 3 ANTENNA CORD SUB-ASSEMBLY
6.CHECK NO. 3 ANTENNA CORD SUB-ASSEMBLY
a.
E333592C03
0.125,0.052 0.438,0.208 0.313,0.156 10 false *a 0.188,1.75 0.5,1.906 0.313,0.156 10 false *b
*a Front view of wire harness connector
(to No.1 Amplifier Antenna Assembly)
*b Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly)


Disconnect the antenna connector from the No. 1 amplifier antenna assembly.


b.

Disconnect the antenna connector from the No. 2 antenna cord sub-assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 - 1 Always Below 1 Ω
1 - 3 Always Below 1 Ω
2 - Body ground Always 10 kΩ or higher
1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK NO. 2 ANTENNA CORD SUB-ASSEMBLY

NG

7.CHECK NO. 2 ANTENNA CORD SUB-ASSEMBLY
a.
E288795C02
0.26,0.104 0.573,0.26 0.313,0.156 10 false *a 0.271,1.677 0.583,1.833 0.313,0.156 10 false *b
*a Front view of wire harness connector
(to No. 3 Antenna Cord Sub-assembly)
*b Front view of wire harness connector
(to Antenna Cord Sub-assembly)


Disconnect the antenna connector from the No. 3 antenna cord sub-assembly.


b.

Disconnect the antenna connector from the antenna cord sub-assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 Always Below 1 Ω
3 - 3 Always Below 1 Ω
1 - Body ground Always 10 kΩ or higher
3 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.CHECK ANTENNA CORD SUB-ASSEMBLY

NG

8.CHECK ANTENNA CORD SUB-ASSEMBLY
a.
E288797C03
0.521,2.271 0.958,2.521 0.438,0.25 2.063,2.51 2.375,2.208 2.375,2.208 2.583,2.208 true 1.583,2.833 1.135,2.979 1.135,2.979 0.885,2.979 true 0.229,0.073 0.542,0.229 0.313,0.156 10 false *a 0.271,1.542 0.583,1.698 0.313,0.156 10 false *b 0.635,2.323 0.948,2.479 0.313,0.156 10 false RA 2.625,2.115 3.104,2.302 0.479,0.188 10 false ANT+ 0.49,2.896 0.969,3.083 0.479,0.188 10 false MAIN
*a Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly)
*b Front view of wire harness connector
(to Radio and Display Receiver Assembly)


Disconnect the antenna connector from the No. 2 antenna cord sub-assembly.


b.

Disconnect the antenna connector from the radio and display receiver assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 - RA-3 (MAIN) Always Below 1 Ω
3 - RA-5 (ANT+) Always Below 1 Ω
2 - Body ground Always 10 kΩ or higher
3 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.CHECK NO. 1 AMPLIFIER ANTENNA ASSEMBLY

NG

9.CHECK NO. 1 AMPLIFIER ANTENNA ASSEMBLY
a.

Replace the No. 1 amplifier antenna assembly and check if radio broadcasts can be received normally.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AMPLIFIER ANTENNA>REMOVAL

OK:

Radio broadcasts can be received normally.



Result:
Proceed to
OK
NG



OK

END (NO. 1 AMPLIFIER ANTENNA ASSEMBLY IS DEFECTIVE)

NG

REPLACE RADIO & DISPLAY RECEIVER ASSEMBLY

10.CHECK NO. 3 ANTENNA CORD SUB-ASSEMBLY
a.
E332809C05
0.125,0.052 0.438,0.208 0.313,0.156 10 false *a 0.208,1.833 0.521,1.99 0.313,0.156 10 false *b
*a Front view of wire harness connector
(to Satellite Radio Antenna Assembly)
*b Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly)


Disconnect the antenna connector from the Satellite Radio Antenna Assembly.


b.

Disconnect the antenna connector from the No. 2 antenna cord sub-assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 - 1 Always Below 1 Ω
1 - 3 Always Below 1 Ω
2 - Body ground Always 10 kΩ or higher
1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

11.CHECK NO. 2 ANTENNA CORD SUB-ASSEMBLY

NG

11.CHECK NO. 2 ANTENNA CORD SUB-ASSEMBLY
a.
E288795C02
0.26,0.104 0.573,0.26 0.313,0.156 10 false *a 0.271,1.677 0.583,1.833 0.313,0.156 10 false *b
*a Front view of wire harness connector
(to No. 3 Antenna Cord Sub-assembly)
*b Front view of wire harness connector
(to Antenna Cord Sub-assembly)


Disconnect the antenna connector from the No. 3 antenna cord sub-assembly.


b.

Disconnect the antenna connector from the antenna cord sub-assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 Always Below 1 Ω
3 - 3 Always Below 1 Ω
1 - Body ground Always 10 kΩ or higher
3 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

12.CHECK ANTENNA CORD SUB-ASSEMBLY

NG

12.CHECK ANTENNA CORD SUB-ASSEMBLY
a.
E288797C03
0.521,2.271 0.958,2.521 0.438,0.25 2.063,2.51 2.375,2.208 2.375,2.208 2.583,2.208 true 1.583,2.833 1.135,2.979 1.135,2.979 0.885,2.979 true 0.229,0.073 0.542,0.229 0.313,0.156 10 false *a 0.271,1.542 0.583,1.698 0.313,0.156 10 false *b 0.635,2.323 0.948,2.479 0.313,0.156 10 false RA 2.625,2.115 3.104,2.302 0.479,0.188 10 false ANT+ 0.49,2.896 0.969,3.083 0.479,0.188 10 false MAIN
*a Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly)
*b Front view of wire harness connector
(to Radio and Display Receiver Assembly)


Disconnect the antenna connector from the No. 2 antenna cord sub-assembly.


b.

Disconnect the antenna connector from the radio and display receiver assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 - RA-3 (MAIN) Always Below 1 Ω
3 - RA-5 (ANT+) Always Below 1 Ω
2 - Body ground Always 10 kΩ or higher
3 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

13.CHECK SATELLITE RADIO ANTENNA ASSEMBLY

NG

13.CHECK SATELLITE RADIO ANTENNA ASSEMBLY
a.

Replace the satellite radio antenna assembly and check if radio broadcasts can be received normally.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AMPLIFIER ANTENNA>REMOVAL

OK:

Radio broadcasts can be received normally.



Result:
Proceed to
OK
NG



OK

END (SATELLITE RADIO ANTENNA ASSEMBLY IS DEFECTIVE)

NG

REPLACE RADIO & DISPLAY RECEIVER ASSEMBLY