Home › Suspension › ALIGNMENT / HANDLING DIAGNOSIS › FRONT WHEEL ALIGNMENT › from 2015.10
RM3090E _53 Suspension _008763 ALIGNMENT / HANDLING DIAGNOSIS _0049350 FRONT WHEEL ALIGNMENT N

ALIGNMENT / HANDLING DIAGNOSIS  FRONT WHEEL ALIGNMENT  ADJUSTMENT  


PROCEDURE

Hide 2.MEASURE VEHICLE HEIGHT

C276113N01
0.167,3.792 0.323,3.99 0.156,0.198 10 A 1.51,3.75 1.667,3.948 0.156,0.198 10 C 3.198,3.823 3.354,4.021 0.156,0.198 10 D 2.885,3.802 3.042,4 0.156,0.198 10 B

NOTICE:
·

Before inspecting the wheel alignment, adjust the vehicle height to the specified value.

·

Be sure to perform the measurement on a level surface.

·

If it is necessary to go under the vehicle for measurement, make sure that the parking brake is applied and the vehicle is secured with chocks.



a.

Bounce the vehicle up and down at the corners several times to stabilize the suspension.


b.

Measure the vehicle height.

Measuring points:
A:

Ground clearance of center of front No. 1 lower suspension arm bushing set bolt

B:

Ground clearance of center of rear No. 2 suspension arm bushing set bolt

C:

Ground clearance of center of front wheel

D:

Ground clearance of center of rear wheel


Standard Vehicle Height (Unloaded Vehicle):
Item Front C - A Rear D - B
- 102 mm (4.02 in.) 72 mm (2.83 in.)
Rough Road Package 92 mm (3.62 in.) 62 mm (2.44 in.)


NOTICE:

The standard value shown here is a value that is used for adjusting the wheel alignment and does not indicate the height of an actual vehicle.


HINT:

If the vehicle height is not as specified, press down on the vehicle several times to stabilize the suspension. Then measure the vehicle height again.



Hide 3.INSPECT CAMBER, CASTER AND STEERING AXIS INCLINATION

a.
C132440C14
2.406,1.104 2.51,0.823 2.51,0.823 2.74,0.823 false 0.906,0.708 1.031,0.708 1.031,0.708 1.031,1.479 false 0.698,0.615 1.01,0.771 0.313,0.156 10 *a 2.833,0.75 3.146,0.906 0.313,0.156 10 *b
*a Alignment Tester
*b Gauge


Install a camber-caster-kingpin gauge or place the front wheels on the center of a wheel alignment tester.


b.

Inspect the camber, caster and steering axis inclination.

Standard Camber Inclination (Unloaded Vehicle):
Item Camber Inclination Right-left Difference
- -0°12' +/-45'
(-0.20° +/-0.75°)
30' (0.50°) or less
Rough Road Package -0°09' +/-45'
(-0.15° +/-0.75°)
30' (0.50°) or less


Standard Caster Inclination (Unloaded Vehicle):
Item Tire Size Caster Inclination Right-left Difference
- 215/70R16 5°52' +/-45'
(5.87° +/-0.75°)
30' (0.50°) or less
225/65R17 5°55' +/-45'
(5.92° +/-0.75°)
30' (0.50°) or less
235/55R18 5°54' +/-45'
(5.90° +/-0.75°)
30' (0.50°) or less
225/60R18 5°51' +/-45'
(5.85° +/-0.75°)
30' (0.50°) or less
Rough Road Package 225/65R17 5°48' +/-45'
(5.80° +/-0.75°)
30' (0.50°) or less
235/55R18 5°49' +/-45'
(5.82° +/-0.75°)
30' (0.50°) or less


Standard Steering Axis Inclination (Unloaded Vehicle):
Item Tire Size Steering Axis Inclination
- 215/70R16
225/65R17
235/55R18
11°32' +/-30'
(11.53° +/-0.50°)
225/60R18 11°33' +/-30'
(11.55° +/-0.50°)
Rough Road Package 225/65R17
235/55R18
11°20' +/-30'
(11.33° +/-0.50°)



Hide 4.ADJUST CAMBER

NOTICE:

Inspect toe-in after the camber has been adjusted.


a.

Remove the front wheel.


b.
C276122

Remove the bolt, detach the clamp and disconnect the front speed sensor.


c.
C153576

Remove the bolt and disconnect the front flexible hose.


d.
C154929

Remove the 2 nuts on the lower side of the front shock absorber.

NOTICE:

Keep the bolts inserted.



e.

Remove the top and bottom bolts one at a time and confirm that the steering knuckle can move freely in the front shock absorber.

NOTICE:

Do not apply lubricants to the steering knuckle and shock absorber contact surfaces.


HINT:
·

Reinstall each bolt after removing it and confirming steering knuckle movement.

·

If the steering knuckle does not move freely in the front shock absorber, clean the installation surfaces of the front shock absorber and the steering knuckle.




f.

Temporarily install the 2 nuts (Step A).


g.
C131799

Fully push or pull the front axle hub in the direction of the required adjustment (Step B).


h.
C154929

Tighten the nuts.

Torque:
240 N*m (2447 kgf*cm, 177 ft.*lbf)

NOTICE:

Prevent the bolts from rotating when tightening the nuts.



i.
C153576

Connect the front flexible hose to the steering knuckle with the bolt.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


j.
C276122

Connect the front flexible hose and front speed sensor with the bolt.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)

NOTICE:

Do not twist the front speed sensor when installing it.



k.

Attach the clamp of the front speed sensor.


l.

Install the front wheel.

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)


m.

Check the camber.

Standard Camber Inclination (Unloaded Vehicle):
Item Camber Inclination Right-left Difference
- -0°12' +/-45'
(-0.20° +/-0.75°)
30' (0.50°) or less
Rough Road Package -0°09' +/-45'
(-0.15° +/-0.75°)
30' (0.50°) or less



n.
C140710N01
1.844,0.365 2.479,0.365 false 1.844,1.229 1.844,0.667 false 2.542,0.271 2.698,0.469 0.156,0.198 10 1 1.813,1.26 1.969,1.458 0.156,0.198 10 2

Check the camber.

If the measured value is not within the specification, calculate the required adjustment amount using the formula below.

Camber adjustment amount = center value of the specified range - measured value.

Check the combination of installed bolts. Select appropriate bolts from the table below to adjust the camber to the specified values.

HINT:

Try to adjust the camber to the center of the specified range.


Move Axle toward (+) in Step (B) Move Axle toward (-) in Step (B)
Refer to table (1) (When moving the axle toward the positive side) Refer to table (2) (When moving the axle toward the negative side)

NOTICE:

Replace the nut with a new one when replacing a bolt.


i.

Table (1) (To move the axle hub toward the positive side)

C212217C06
2.052,0.531 2.188,0.74 0.135,0.208 10 1 2.052,1.146 2.188,1.354 0.135,0.208 10 2 2.521,0.792 2.75,0.99 0.229,0.198 10 *c 3.219,1.406 3.448,1.594 0.229,0.188 10 *d 5.979,0.792 6.198,0.99 0.219,0.198 10 *e 5.271,0.792 5.521,0.99 0.25,0.198 10 *d 4.604,1.406 4.781,1.583 0.177,0.177 10 *f 3.917,1.406 4.125,1.615 0.208,0.208 10 *e 4.396,6.375 4.583,6.552 0.188,0.177 10 *f 5.969,1.396 6.177,1.552 0.208,0.156 10 *f 5.271,1.406 5.469,1.583 0.198,0.177 10 *f 6.656,1.396 6.833,1.552 0.177,0.156 10 *f 6.646,0.792 6.854,0.969 0.208,0.177 10 *f 2.542,2.99 2.719,3.219 0.177,0.229 10 A 2.542,4.188 2.771,4.406 0.229,0.219 10 F 2.542,3.469 2.771,3.688 0.229,0.219 10 C 2.542,3.938 2.74,4.156 0.198,0.219 10 E 2.542,3.24 2.729,3.448 0.188,0.208 10 B 2.542,3.708 2.729,3.927 0.188,0.219 10 D 3.927,3.01 4.177,3.24 0.25,0.229 10 C 5.271,3 5.51,3.229 0.24,0.229 10 E 3.229,3.01 3.406,3.219 0.177,0.208 10 B 4.604,3 4.792,3.24 0.188,0.24 10 D 3.229,2.76 3.448,2.99 0.219,0.229 10 G 3.229,3.24 3.406,3.448 0.177,0.208 10 C 3.229,3.708 3.448,3.938 0.219,0.229 10 E 3.229,3.469 3.427,3.698 0.198,0.229 10 D 3.229,3.938 3.427,4.167 0.198,0.229 10 F 3.927,2.51 4.115,2.74 0.188,0.229 10 G 3.927,2.76 4.135,2.969 0.208,0.208 10 A 3.927,3.708 4.115,3.938 0.188,0.229 10 F 3.917,3.469 4.083,3.688 0.167,0.219 10 E 3.927,3.24 4.135,3.458 0.208,0.219 10 D 4.604,2.281 4.802,2.531 0.198,0.25 10 G 6.656,1.563 6.833,1.823 0.177,0.26 10 G 5.979,1.813 6.26,2.063 0.281,0.25 10 G 5.271,2.031 5.458,2.281 0.188,0.25 10 G 6.656,1.813 6.813,2.042 0.156,0.229 10 A 6.656,2.281 6.844,2.531 0.188,0.25 10 C 6.656,2.76 6.885,3.01 0.229,0.25 10 E 6.656,2.031 6.833,2.26 0.177,0.229 10 B 6.656,2.51 6.875,2.781 0.219,0.271 10 D 5.979,2.031 6.177,2.292 0.198,0.26 10 A 5.979,2.51 6.188,2.75 0.208,0.24 10 C 5.979,2.281 6.26,2.531 0.281,0.25 10 B 5.979,2.76 6.167,2.99 0.188,0.229 10 D 5.979,3 6.115,3.208 0.135,0.208 10 F 5.271,3.24 5.49,3.448 0.219,0.208 10 F 5.271,2.281 5.406,2.51 0.135,0.229 10 A 5.271,2.76 5.448,2.969 0.177,0.208 10 C 5.271,2.51 5.438,2.74 0.167,0.229 10 B 4.604,2.51 4.781,2.76 0.177,0.25 10 A 4.604,2.76 4.781,2.969 0.177,0.208 10 B 4.604,3.24 4.813,3.458 0.208,0.219 10 E 4.604,3.469 4.813,3.698 0.208,0.229 10 F 1.625,5.073 1.76,5.281 0.135,0.208 10 A 5.094,5.073 5.229,5.281 0.135,0.208 10 F 3.052,5.073 3.188,5.281 0.135,0.208 10 C 4.406,5.073 4.542,5.281 0.135,0.208 10 E 2.344,5.073 2.479,5.281 0.135,0.208 10 B 3.729,5.073 3.865,5.281 0.135,0.208 10 D 5.802,5.073 5.938,5.281 0.135,0.208 10 G 1.073,5.5 1.208,5.708 0.135,0.208 10 1 1.104,6.135 1.24,6.344 0.135,0.208 10 2 3.042,6.375 3.229,6.531 0.188,0.156 10 *f 3.719,6.375 3.958,6.542 0.24,0.167 10 *f 5.083,6.375 5.292,6.573 0.208,0.198 10 *f 5.094,5.75 5.292,5.917 0.198,0.167 10 *f 4.385,5.75 4.604,5.917 0.219,0.167 10 *e 2.333,6.375 2.542,6.542 0.208,0.167 10 *e 1.625,6.375 1.854,6.552 0.229,0.177 10 *d 3.719,5.75 3.927,5.938 0.208,0.188 10 *d 3.01,5.75 3.208,5.938 0.198,0.188 10 *c 1.625,5.75 1.844,5.948 0.219,0.198 10 *c 2.333,5.75 2.521,5.906 0.188,0.156 10 *c 5.802,6.365 6.021,6.563 0.219,0.198 10 *c 5.76,5.76 5.969,5.948 0.208,0.188 10 *c 0.177,1.563 2.198,1.75 2.021,0.188 10 -1°30' to -1°15' (-1.50° to -1.25°) 0.406,2.76 1.969,2.948 1.563,0.188 10 -0°15' to 0° (-0.25° to 0°) 0.208,2.51 2.156,2.729 1.948,0.219 10 -0°30' to -0°15' (-0.5° to -0.25°) 0.208,2.281 2.156,2.479 1.948,0.198 10 -0°45' to -0°30' (-0.75° to -0.5°) 0.271,2.031 2.104,2.208 1.833,0.177 10 -1°00' to -0°45' (-1° to -0.75°) 0.26,1.813 2.094,2.021 1.833,0.208 10 -1°15' to -1°00' (-1.25° to -1°) 0.354,3.938 2.01,4.115 1.656,0.177 10 1°00' to 1°15' (1° to 1.25°) 0.354,3.708 2,3.906 1.646,0.198 10 0°45' to 1°00' (0.75° to 1°) 0.302,3.469 2.073,3.646 1.771,0.177 10 0°30' to 0°45' (0.5° to 0.75°) 0.302,3.24 2.073,3.417 1.771,0.177 10 0°15' to 0°30' (0.25° to 0.5°) 0.448,3 1.917,3.198 1.469,0.198 10 0° to 0°15' (0° to 0.25°) 0.302,4.188 2.073,4.365 1.771,0.177 10 1°15' to 1°30' (1.25° to 1.5°) 2.542,1.406 2.76,1.604 0.219,0.198 10 *c 3.219,0.792 3.448,0.969 0.229,0.177 10 *c 3.917,0.792 4.135,1.01 0.219,0.219 10 *c 4.604,0.792 4.823,1.01 0.219,0.219 10 *c 5.979,3 6.24,3.24 0.26,0.24 10 F 1.156,0.625 1.333,0.792 0.177,0.167 10 *a 0.625,1.115 0.802,1.281 0.177,0.167 10 *b 0.875,4.792 1.198,5.021 0.323,0.229 12 *B 0.063,0.135 0.333,0.333 0.271,0.198 12 *A
*A Table (1) (To move the axle hub toward the positive side) *B Selected Bolt Combination
*a Installed Bolt *b Adjusting Value
*c Standard Bolt *d 90105-17009
*e 90105-17010 *f 90105-17011



ii.

Table (2) (To move the axle hub toward the negative side)

C212218C06
2.052,0.531 2.188,0.74 0.135,0.208 10 1 2.052,1.146 2.188,1.354 0.135,0.208 10 2 1.635,5.052 1.771,5.26 0.135,0.208 10 A 5.094,5.052 5.229,5.26 0.135,0.208 10 F 3.052,5.052 3.188,5.26 0.135,0.208 10 C 4.406,5.052 4.542,5.26 0.135,0.208 10 E 2.344,5.052 2.479,5.26 0.135,0.208 10 B 3.729,5.052 3.865,5.26 0.135,0.208 10 D 5.802,5.052 5.938,5.26 0.135,0.208 10 G 1.073,5.5 1.208,5.708 0.135,0.208 10 1 1.104,6.135 1.24,6.344 0.135,0.208 10 2 0.177,1.563 2.198,1.75 2.021,0.188 10 -1°30' to -1°15' (-1.50° to -1.25°) 0.406,2.76 1.969,2.948 1.563,0.188 10 -0°15' to 0° (-0.25° to 0°) 0.208,2.521 2.156,2.74 1.948,0.219 10 -0°30' to -0°15' (-0.5° to -0.25°) 0.208,2.281 2.156,2.479 1.948,0.198 10 -0°45' to -0°30' (-0.75° to -0.5°) 0.271,2.031 2.104,2.208 1.833,0.177 10 -1°00' to -0°45' (-1° to -0.75°) 0.26,1.813 2.094,2.021 1.833,0.208 10 -1°15' to -1°00' (-1.25° to -1°) 0.354,3.938 2.01,4.115 1.656,0.177 10 1°00' to 1°15' (1° to 1.25°) 0.354,3.708 2,3.906 1.646,0.198 10 0°45' to 1°00' (0.75° to 1°) 0.302,3.469 2.073,3.646 1.771,0.177 10 0°30' to 0°45' (0.5° to 0.75°) 0.302,3.24 2.073,3.417 1.771,0.177 10 0°15' to 0°30' (0.25° to 0.5°) 0.448,3 1.917,3.198 1.469,0.198 10 0° to 0°15' (0° to 0.25°) 0.302,4.188 2.073,4.365 1.771,0.177 10 1°15' to 1°30' (1.25° to 1.5°) 1.156,0.625 1.333,0.792 0.177,0.167 10 *a 0.625,1.115 0.802,1.281 0.177,0.167 10 *b 0.875,4.792 1.167,5.021 0.292,0.229 12 *B 0.063,0.135 0.417,0.354 0.354,0.219 12 *A 5.292,2.76 5.427,2.969 0.135,0.208 10 E 5.292,3.708 5.427,3.917 0.135,0.208 10 G 5.292,2.521 5.427,2.729 0.135,0.208 10 F 5.292,3.469 5.427,3.677 0.135,0.208 10 A 5.292,3 5.427,3.208 0.135,0.208 10 C 5.292,3.24 5.427,3.448 0.135,0.208 10 B 2.542,2.76 2.677,2.969 0.135,0.208 10 A 2.542,1.563 2.677,1.771 0.135,0.208 10 F 2.542,2.281 2.677,2.49 0.135,0.208 10 C 2.542,1.813 2.677,2.021 0.135,0.208 10 E 2.542,2.521 2.677,2.729 0.135,0.208 10 B 2.542,2.031 2.677,2.24 0.135,0.208 10 D 3.229,2.76 3.365,2.969 0.135,0.208 10 B 3.229,3 3.365,3.208 0.135,0.208 10 G 3.229,2.521 3.365,2.729 0.135,0.208 10 C 3.229,2.031 3.365,2.24 0.135,0.208 10 E 3.229,2.281 3.365,2.49 0.135,0.208 10 D 3.229,1.813 3.375,2.021 0.146,0.208 10 F 3.927,2.76 4.063,2.969 0.135,0.208 10 C 3.927,3.24 4.063,3.448 0.135,0.208 10 G 3.927,3 4.063,3.208 0.135,0.208 10 A 3.927,2.031 4.063,2.24 0.135,0.208 10 F 3.927,2.281 4.063,2.49 0.135,0.208 10 E 3.927,2.521 4.063,2.729 0.135,0.208 10 D 4.604,2.76 4.74,2.969 0.135,0.208 10 D 4.604,3.469 4.74,3.677 0.135,0.208 10 G 4.604,3.24 4.74,3.448 0.135,0.208 10 A 4.604,3 4.74,3.208 0.135,0.208 10 B 4.604,2.521 4.74,2.729 0.135,0.208 10 E 4.604,2.281 4.74,2.49 0.135,0.208 10 F 5.99,3.938 6.125,4.146 0.135,0.208 10 G 5.99,3.708 6.125,3.917 0.135,0.208 10 A 5.99,3.24 6.125,3.448 0.135,0.208 10 C 5.99,3.469 6.125,3.677 0.135,0.208 10 B 5.99,3 6.125,3.208 0.135,0.208 10 D 5.99,2.76 6.125,2.969 0.135,0.208 10 F 6.688,4.188 6.823,4.396 0.135,0.208 10 G 6.688,3.938 6.823,4.146 0.135,0.208 10 A 6.688,3.469 6.823,3.677 0.135,0.208 10 C 6.688,3 6.823,3.208 0.135,0.208 10 E 6.688,3.708 6.823,3.917 0.135,0.208 10 B 6.688,3.24 6.823,3.448 0.135,0.208 10 D 2.51,0.792 2.729,0.969 0.219,0.177 10 *c 3.219,1.396 3.406,1.573 0.188,0.177 10 *d 5.969,0.781 6.115,0.938 0.146,0.156 10 *e 5.271,0.792 5.469,0.979 0.198,0.188 10 *d 4.604,1.396 4.781,1.573 0.177,0.177 10 *f 3.906,1.396 4.083,1.573 0.177,0.177 10 *e 5.979,1.396 6.188,1.552 0.208,0.156 10 *f 5.281,1.396 5.479,1.573 0.198,0.177 10 *f 6.656,1.396 6.833,1.552 0.177,0.156 10 *f 6.656,0.792 6.823,0.958 0.167,0.167 10 *f 2.51,1.396 2.688,1.573 0.177,0.177 10 *c 3.219,0.792 3.396,0.948 0.177,0.156 10 *c 3.927,0.792 4.115,0.979 0.188,0.188 10 *c 4.604,0.792 4.781,0.958 0.177,0.167 10 *c 4.385,6.375 4.531,6.531 0.146,0.156 10 *f 3.01,6.375 3.198,6.531 0.188,0.156 10 *f 3.708,6.375 3.948,6.542 0.24,0.167 10 *f 5.094,6.375 5.302,6.573 0.208,0.198 10 *f 5.083,5.75 5.271,5.906 0.188,0.156 10 *f 4.375,5.75 4.573,5.906 0.198,0.156 10 *e 2.313,6.375 2.521,6.542 0.208,0.167 10 *e 1.625,6.375 1.771,6.531 0.146,0.156 10 *d 3.688,5.75 3.875,5.938 0.188,0.188 10 *d 3.01,5.75 3.208,5.938 0.198,0.188 10 *c 1.625,5.74 1.802,5.927 0.177,0.188 10 *c 2.323,5.75 2.5,5.906 0.177,0.156 10 *c 5.781,6.375 5.969,6.542 0.188,0.167 10 *c 5.771,5.75 5.979,5.938 0.208,0.188 10 *c
*A Table (2) (To move the axle hub toward the negative side) *B Selected Bolt Combination
*a Installed Bolt *b Adjusting Value
*c Standard Bolt *d 90105-17009
*e 90105-17010 *f 90105-17011




o.

If the camber was out of adjustment in the previous step, perform the adjust camber steps mentioned above. In step A, replace the existing bolts with the selected bolts.

HINT:

Replace one bolt at a time when replacing both bolts.



Hide 5.INSPECT TOE-IN

a.
C260042C01
0.698,0.042 0.844,0.24 0.146,0.198 10 A 2.656,0.031 2.802,0.229 0.146,0.198 10 B 1.719,1.563 1.865,1.76 0.146,0.198 10 C 1.677,0.219 1.823,0.417 0.146,0.198 10 D
V100135

Front of the Vehicle


Bounce the vehicle up and down at the corners to stabilize the suspension and inspect toe-in.

Toe-in (Unloaded Vehicle):
Item Tire Size A + B
C - D
- 215/70R16
225/65R17
235/55R18
A + B: 0°7' +/-10' (0.12°+/-0.16°)
C - D: 1.4 +/-2.0 mm (0.06 +/-0.08 in.)
225/60R18 A + B: 0°7' +/-10' (0.12°+/-0.16°)
C - D: 1.5 +/-2.0 mm (0.06 +/-0.08 in.)
Rough Road Package 225/65R17
235/55R18
A + B: 0°8' +/-10' (0.13°+/-0.16°)
C - D: 1.5 +/-2.0 mm (0.06 +/-0.08 in.)


HINT:

If the toe-in is not within the specified range, adjust it at the rack ends.



Hide 6.ADJUST TOE-IN

a.
C131802C01
2.229,1.521 2.417,1.656 0.188,0.135 10 *a
*a Difference


Make sure that the lengths of the right and left rack ends are almost the same.

Standard difference:

1.5 mm (0.06 in.) or less



b.

Remove the boot clips.


c.
C131801C01
2.281,1.438 2.594,1.594 0.313,0.156 10 *a 2.417,0.74 2.729,0.896 0.313,0.156 10 *b
*a Loosen
*b Turn


Loosen the tie rod end lock nuts.


d.

Turn the right and left rack ends by an equal amount to adjust the toe-in to the center value.


e.

Tighten the tie rod end lock nuts.

Torque:
88 N*m (897 kgf*cm, 65 ft.*lbf)


f.

Place the boots on the seats and install the clips.

NOTICE:

Make sure that the claws of the clip are facing in the direction that the vehicle travels.


HINT:

Make sure that the boots are not twisted.



Hide 7.INSPECT WHEEL ANGLE

C132439C10
0.523,0.183 0.717,0.363 0.194,0.18 10 *a 2.737,0.183 2.931,0.363 0.194,0.18 10 *a 0.865,0.183 1.059,0.363 0.194,0.18 10 *b 2.381,0.183 2.575,0.363 0.194,0.18 10 *b
*a Inside
*b Outside
V100135

Front of the Vehicle


a.

Turn the steering wheel to the left and right full lock positions and measure the turning angle.

Standard Wheel Turning Angle (Unloaded Vehicle):
Item Tire Size Inside Wheel Outside Wheel (Reference)
- 215/70R16 38°36' +/-2°
(38.60° +/-2°)
32°10' +/-2°
(32.17° +/-2°)
225/65R17 38°35' +/-2°
(38.58° +/-2°)
32°10' +/-2°
(32.17° +/-2°)
235/55R18
225/60R18
35°43' +/-2°
(35.72° +/-2°)
30°28' +/-2°
(30.47° +/-2°)
Rough Road Package 225/65R17 38°46' +/-2°
(38.77° +/-2°)
32°23' +/-2°
(32.38° +/-2°)
235/55R18 35°52' +/-2°
(35.87° +/-2°)
30°40' +/-2°
(30.67° +/-2°)


If the angles are not as specified, check and adjust the right and left rack end lengths.



Hide 8.PLACE FRONT WHEELS FACING STRAIGHT AHEAD

Hide 9. PERFORM YAW RATE SENSOR ZERO POINT CALIBRATION

Hide 8646C 10.ADJUST FORWARD RECOGNITION CAMERA