Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › 2015.10–2016.08
RM3090E _58 Vehicle Interior _044382 PRE-CRASH SAFETY _0224751 PRE-CRASH SAFETY SYSTEM C

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  C1A4B  Stop Light Relay Circuit  


DESCRIPTION

The brake actuator assembly (skid control ECU) sends a stop light operation signal to the stop light switch assembly. When the brake actuator assembly (skid control ECU) detects a malfunction in the stop light circuit, the driving support ECU assembly stores DTC C1A4B.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1A4B Stop Light Relay Circuit Either of the following conditions is met:
·

When the ignition switch ON, the IG1 terminal voltage is between 11 to 14 V and the stop light illumination output signal (STPO) is output, the signal is not received at terminal STP for 0.3 seconds or more.

·

When the ignition switch ON, the IG1 terminal voltage is between 11 to 14 V and the stop light illumination output signal (STPO) is not output, the signals received at terminals STP and STP2 are different for 0.3 seconds or more.


·

Lighting system

·

Vehicle stability control system

·

Harness or connector

·

Stop light switch assembly

·

Brake actuator assembly (skid control ECU)

·

Entry and start system (w/ entry and start system)



WIRING DIAGRAM

E337398E02
5.5,4.875 7.083,5.271 1.583,0.396 10 false Brake Actuator Assembly (Skid Control ECU) 1.25,1.406 3.292,1.615 2.042,0.208 10 false Driving Support ECU Assembly 0.313,2.708 2.354,2.917 2.042,0.208 10 false from Battery 1.708,2.854 2.219,3.052 0.51,0.198 10 false STOP 3.698,3.615 4.208,3.813 0.51,0.198 10 false IC 2.885,4.719 5.104,4.938 2.219,0.219 10 false Stop Light Switch Assembly 2.896,4.552 3.406,4.75 0.51,0.198 10 false A77 0.656,8.427 3.656,8.656 3,0.229 10 false : CAN Communication Line 2.323,2.583 2.833,2.781 0.51,0.198 10 false 7 2.323,3.792 2.833,3.99 0.51,0.198 10 false 2 2.573,3.792 3.083,3.99 0.51,0.198 10 false GND 2.583,2.583 3.094,2.781 0.51,0.198 10 false B 4.854,2.583 5.365,2.781 0.51,0.198 10 false L 4.667,3.188 5.177,3.385 0.51,0.198 10 false ACC 4.667,3.792 5.177,3.99 0.51,0.198 10 false OUT 5.875,2.583 6.385,2.781 0.51,0.198 10 false STP2 5.875,3.177 6.385,3.375 0.51,0.198 10 false STPO 5.875,3.792 6.385,3.99 0.51,0.198 10 false STP 5.635,2.583 6.146,2.781 0.51,0.198 10 false 5 5.563,3.177 6.073,3.375 0.51,0.198 10 false 26 5.563,3.792 6.073,3.99 0.51,0.198 10 false 35 5.094,3.792 5.604,3.99 0.51,0.198 10 false 1 5.094,3.177 5.604,3.375 0.51,0.198 10 false 4 5.094,2.583 5.604,2.781 0.51,0.198 10 false 3 1.135,5.865 3.354,6.083 2.219,0.219 10 false Center Stop Light Assembly 1.146,5.698 1.656,5.896 0.51,0.198 10 false U1 1.344,5.271 1.854,5.469 0.51,0.198 10 false 1 2.448,5.271 2.958,5.469 0.51,0.198 10 false 2 2.188,5.271 2.698,5.469 0.51,0.198 10 false B 1.583,5.271 2.094,5.469 0.51,0.198 10 false E 2.99,6.583 5.583,6.792 2.594,0.208 10 false Rear Combination Light Assembly LH 2.99,6.427 3.5,6.625 0.51,0.198 10 false N13 2.99,7.885 5.583,8.094 2.594,0.208 10 false Rear Combination Light Assembly RH 2.99,7.729 3.5,7.927 0.51,0.198 10 false M19 3.458,6 3.969,6.198 0.51,0.198 10 false E 3.458,7.302 3.969,7.5 0.51,0.198 10 false E 4.052,6 4.563,6.198 0.51,0.198 10 false B 4.052,7.302 4.563,7.5 0.51,0.198 10 false B 4.271,6 4.781,6.198 0.51,0.198 10 false 1 4.271,7.302 4.781,7.5 0.51,0.198 10 false 1 3.229,6 3.74,6.198 0.51,0.198 10 false 4 3.229,7.302 3.74,7.5 0.51,0.198 10 false 4 5.51,4.708 6.021,4.906 0.51,0.198 10 false A80

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When replacing the brake actuator assembly (skid control ECU), perform zero point calibration.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION

·

When the entry and start function does not operate, check the entry and start system (start function)*.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING


*: w/ Entry and Start System



PROCEDURE

1.CHECK STOP LIGHT OPERATION
a.

Check that the stop lights come on when the brake pedal is depressed and go off when the brake pedal is released.

OK:
Condition Illumination Condition
Brake pedal depressed On
Brake pedal released Off



Result:
Result Proceed to
OK (w/ Entry and Start System) A
OK (w/o Entry and Start System) B
NG C



A

2.CHECK HARNESS AND CONNECTOR (STPO TERMINAL VOLTAGE)

B

7.CHECK HARNESS AND CONNECTOR (STP2 TERMINAL VOLTAGE)

C

2.CHECK HARNESS AND CONNECTOR (STPO TERMINAL VOLTAGE)
a.

Turn the ignition switch off.


b.
E296982C19
1.51,0.188 1.938,0.396 0.427,0.208 1.031,1.406 1.01,1.896 1.01,1.896 0.74,1.896 true 0.125,0.083 0.438,0.24 0.313,0.156 10 false *a 1.615,0.208 1.927,0.365 0.313,0.156 10 false A80 0.344,1.823 0.74,2 0.396,0.177 10 false STPO
*a Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU])


Disconnect the brake actuator assembly (skid control ECU) connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A80-26 (STPO) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.PERFORM ACTIVE TEST USING GTS (STOP LIGHT RELAY)

NG

6.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BRAKE ACTUATOR ASSEMBLY [SKID CONTROL ECU])
3.PERFORM ACTIVE TEST USING GTS (STOP LIGHT RELAY)
a.

Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.


b.

Perform "Active Test" according to the display on GTS.

Chassis > ABS/VSC/TRC > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Stop Light Relay Stop lights ON or OFF Test possible at vehicle speed of 0 km/h (0 mph)
Chassis > ABS/VSC/TRC > Active Test
Tester Display
Stop Light Relay
50004 105 5

c.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


d.

Check the stop light switch assembly operation using the Data List and stop light operation by performing an Active Test.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light Relay Output Stop light control relay output ON or OFF ON: Relay output on (Stop light on)
OFF: Relay output off (Stop light off)
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
Stop Light Relay
50003 105 287

Result:
Result Proceed to
When Active Test performed, Data List item not changes between ON and OFF A
When Active Test performed, Data List item changes between ON and OFF and stop lights turn on and off B



A

4.INSPECT BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)

B

5.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BRAKE ACTUATOR ASSEMBLY [SKID CONTROL ECU])
4.INSPECT BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)
a.

Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.


b.

Perform "Active Test" according to the display on GTS.

Chassis > ABS/VSC/TRC > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Stop Light Relay Stop lights ON or OFF Test possible at vehicle speed of 0 km/h (0 mph)
Chassis > ABS/VSC/TRC > Active Test
Tester Display
Stop Light Relay
50004 105 5

c.
E337400C01
1.5,0.219 1.917,0.469 0.417,0.25 1.75,1.167 2.167,0.5 2.167,0.5 2.333,0.5 true 0.146,0.115 0.458,0.313 0.313,0.198 10 false *a 1.604,0.271 1.917,0.469 0.313,0.198 10 false A77 2.417,0.417 2.833,0.625 0.417,0.208 10 false ACC
*a Component with harness connected
(Stop Light Switch Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A77-4 (ACC) - Body ground Active test is OFF 11 to 14 V
A77-4 (ACC) - Body ground Active test is ON Below 1.5 V



Result:
Proceed to
OK
NG



OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)

5.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BRAKE ACTUATOR ASSEMBLY [SKID CONTROL ECU])
a.

Disconnect the A80 brake actuator assembly (skid control ECU) connector.


b.

Disconnect the A77 stop light switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A80-35 (STP) - A77-1 (OUT) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BRAKE ACTUATOR ASSEMBLY [SKID CONTROL ECU])
a.

Disconnect the A80 brake actuator assembly (skid control ECU) connector.


b.

Disconnect the A77 stop light switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A80-26 (STPO) - A77-4 (ACC) Always Below 1 Ω
A80-26 (STPO) or A77-4 (ACC) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (STP2 TERMINAL VOLTAGE)
a.

Turn the ignition switch off.


b.
E296982C20
1.51,0.188 1.938,0.396 0.427,0.208 1.448,0.906 1.198,0.333 1.198,0.333 1.01,0.333 true 0.125,0.083 0.438,0.24 0.313,0.156 10 false *a 1.615,0.208 1.927,0.365 0.313,0.156 10 false A80 0.646,0.24 1.042,0.417 0.396,0.177 10 false STP2
*a Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU])


Disconnect the brake actuator assembly (skid control ECU) connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A80-5 (STP2) - Body ground Stop light switch assembly on (Brake pedal depressed) 8.5 to 14 V
A80-5 (STP2) - Body ground Stop light switch assembly off (Brake pedal released) Below 1.5 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (STPO TERMINAL VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR