Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU) › from 2015.10
RM3090E _57 Power Source / Network _008434 NETWORKING _0221948 CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU)  Engine Stop and Start ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Engine Stop and Start ECU Communication Stop Mode Either condition is met:
·

"Stop and Go/Start" is not displayed on "CAN Bus Check".

(Click here)

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Engine Stop and Start ECU Communication Stop Mode" in "DTC Combination Table".

(Click here)


·

Power source or inside engine stop and start ECU

·

Engine stop and start ECU CAN branch wire or connector

·

Engine stop and start ECU



WIRING DIAGRAM

C347358E06
0.427,1.615 4.552,1.813 4.125,0.198 10 false G188 0.438,1.75 4.563,1.948 4.125,0.198 10 false No. 6 CAN Junction Connector 1.688,0.563 2.542,0.802 0.854,0.24 10 false 5 1.698,1.156 2.552,1.396 0.854,0.24 10 false 16 5.188,0.667 6.042,0.906 0.854,0.24 10 false G87 5.635,0.677 6.49,0.917 0.854,0.24 10 false CANH 5.188,1.25 6.042,1.49 0.854,0.24 10 false G87 5.646,1.26 6.5,1.5 0.854,0.24 10 false CANL 5.208,1.042 6.063,1.281 0.854,0.24 10 false 14 5.198,0.448 6.052,0.688 0.854,0.24 10 false 13 5.188,6.135 6.042,6.375 0.854,0.24 10 false A86 5.188,6.729 6.042,6.969 0.854,0.24 10 false A86 5.188,7.26 6.042,7.5 0.854,0.24 10 false A66 5.646,7.25 6.5,7.49 0.854,0.24 10 false DGND 5.625,6.75 6.479,6.99 0.854,0.24 10 false GND2 5.646,6.167 6.5,6.406 0.854,0.24 10 false GND1 5.26,7.052 6.115,7.292 0.854,0.24 10 false 6 5.26,6.5 6.115,6.74 0.854,0.24 10 false 2 5.26,5.938 6.115,6.177 0.854,0.24 10 false 8 0.5,7.26 1.354,7.5 0.854,0.24 10 false *1: for 2WW 0.5,7.594 2.365,7.781 1.865,0.188 10 false *2: for 3ZR-FAE 0.5,7.917 2.781,8.188 2.281,0.271 10 false *3: for Manual Transaxle System 0.51,8.24 2.375,8.427 1.865,0.188 10 false *4: for CVT 5.198,2.427 6.052,2.667 0.854,0.24 10 false A66 5.625,2.427 6.479,2.667 0.854,0.24 10 false +B 5.271,2.219 6.125,2.458 0.854,0.24 10 false 1 4,2.26 4.781,2.615 0.781,0.354 10 false EFI NO.1 1.375,2.427 3.229,2.76 1.854,0.333 10 false from EFI-MAIN NO.1 Relay 3.813,2.854 4.833,3.208 1.021,0.354 10 false BBC*1, *2, *3, BBC NO.3*2, *4 2.26,3.125 4.115,3.458 1.854,0.333 10 false from Battery 2.271,3.74 4.125,4.073 1.854,0.333 10 false from Battery 5.177,3.135 6.031,3.375 0.854,0.24 10 false A86 5.177,3.75 6.031,3.99 0.854,0.24 10 false A86 5.646,3.781 6.5,4.021 0.854,0.24 10 false BIN2 5.656,3.146 6.51,3.385 0.854,0.24 10 false BIN1 5.271,2.927 6.125,3.167 0.854,0.24 10 false 3 5.271,3.552 6.125,3.792 0.854,0.24 10 false 1 4.052,3.646 5.083,3.896 1.031,0.25 10 false BBC NO.2 4.115,4.219 5.146,4.469 1.031,0.25 10 false EPS-IG 1.74,4.313 3.594,4.646 1.854,0.333 10 false from IG1 NO.1 Relay 2.135,4.917 3.99,5.25 1.854,0.333 10 false from IG2 Relay 2.052,5.479 3.906,5.813 1.854,0.333 10 false from ACC Relay 4.198,4.792 5.229,5.042 1.031,0.25 10 false IGN 4.198,5.375 5.229,5.625 1.031,0.25 10 false ACC 5.646,5.479 6.677,5.729 1.031,0.25 10 false ACC 5.177,5.49 6.031,5.729 0.854,0.24 10 false G87 5.177,4.917 6.031,5.156 0.854,0.24 10 false G87 5.198,4.344 6.052,4.583 0.854,0.24 10 false G87 5.646,4.333 6.5,4.573 0.854,0.24 10 false IG1 5.656,4.927 6.51,5.167 0.854,0.24 10 false IG2 5.219,4.104 6.073,4.344 0.854,0.24 10 false 21 5.219,4.698 6.073,4.938 0.854,0.24 10 false 18 5.219,5.26 6.073,5.5 0.854,0.24 10 false 19 5.135,8.083 7,8.271 1.865,0.188 10 false Engine Stop and Start ECU

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

DTC check procedure: Turn the ignition switch to ON and wait at least 60 seconds.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU)>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (ENGINE STOP AND START ECU CAN BRANCH WIRE)
a.
C251435C31
0.313,0.927 0.677,1.156 0.365,0.229 2.646,1.5 2.406,1.5 2.406,1.5 2.313,1.188 true 2.573,1.698 2.333,1.698 2.333,1.698 2.229,1.198 true 0.354,0.969 0.813,1.167 0.458,0.198 10 false G87 0.073,0.094 0.531,0.292 0.458,0.198 10 false *a 2.677,1.417 3.135,1.615 0.458,0.198 10 false CANH 2.615,1.625 3.073,1.823 0.458,0.198 10 false CANL
*a Rear view of wire harness connector
(to Engine Stop and Start ECU)


Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the engine stop and start ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G87-13 (CANH) - G87-14 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE ENGINE STOP AND START ECU CAN BRANCH WIRE OR CONNECTOR (CANH, CANL)

2.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - BATTERY AND BODY GROUND)
a.

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


C347357C01
5.583,0.635 6.073,0.854 0.49,0.219 3.365,0.583 3.854,0.802 0.49,0.219 1.188,0.635 1.677,0.854 0.49,0.219 0.271,1.281 0.396,1.281 0.396,1.281 0.49,1.594 true 2.74,1.052 2.865,1.052 2.865,1.052 3.042,1.406 true 2.615,2.24 2.74,2.24 2.74,2.24 3.01,1.865 true 5.229,2.219 5.354,2.219 5.354,2.219 5.531,1.865 true 5.427,2.438 5.552,2.438 5.552,2.438 5.615,1.844 true 6.385,2.333 6.229,2.333 6.229,2.333 6.021,1.854 true 4.458,2.344 4.302,2.344 4.302,2.344 4.094,1.865 true 0.604,0.99 0.729,0.99 0.729,0.99 1.021,1.563 true 4.573,1.104 4.417,1.104 4.417,1.104 4.094,1.406 true 0.083,0.063 0.396,0.219 0.313,0.156 10 false *a 3.49,0.594 3.802,0.75 0.313,0.156 10 false A86 1.323,0.667 1.635,0.823 0.313,0.156 10 false A66 5.708,0.635 6.021,0.792 0.313,0.156 10 false G87 0.052,1.167 0.365,1.323 0.313,0.156 10 false +B 2.25,2.125 2.604,2.313 0.354,0.188 10 false BIN1 2.375,0.948 2.729,1.135 0.354,0.188 10 false BIN2 6.427,2.219 6.781,2.406 0.354,0.188 10 false IG1 4.958,2.115 5.313,2.302 0.354,0.188 10 false IG2 5.094,2.344 5.448,2.531 0.354,0.188 10 false ACC 4.49,2.219 4.99,2.396 0.5,0.177 10 false GND1 0.167,0.885 0.667,1.094 0.5,0.208 10 false DGND 4.625,1 5.125,1.177 0.5,0.177 10 false GND2
*a Front view of wire harness connector
(to Engine Stop and Start ECU)
- -



b.

Disconnect the engine stop and start ECU connectors.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A86-3 (BIN1) - Body ground Always 9.5 to 14 V
A86-1 (BIN2) - Body ground Always 9.5 to 14 V
A66-1 (+B) - Body ground Ignition switch ON 9.5 to 14 V
G87-21 (IG1) - Body ground Ignition switch ON 9.5 to 14 V
G87-18 (IG2) - Body ground Ignition switch ON 9.5 to 14 V
G87-19 (ACC) - Body ground Ignition switch ACC 9.5 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A66-6 (DGND) - Body ground Always Below 1 Ω
A86-8 (GND1) - Body ground Always Below 1 Ω
A86-2 (GND2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR