The main body ECU (multiplex network body ECU) and tire pressure warning ECU and receiver are connected using 2 direct lines that they use to communicate with each other.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B1247 | Tire Pressure Monitor Receiver Communication Stop | In diagnostic mode, an applicable RDA signal cannot be received within 10 seconds after a PRG signal is sent from the main body ECU (multiplex network body ECU). | ·
Tire pressure warning ECU and receiver ·
Wire harness or connector ·
Main body ECU (multiplex network body ECU) ·
ECU-IG NO. 2 fuse*1 ·
Backup boost converter circuit*2 |
*1: w/o Stop and Start System
*2: w/ Stop and Start System
When replacing the tire pressure warning ECU and receiver, read the IDs stored in the old ECU using the GTS and write them down before removal.
It is necessary to perform initialization (Click here Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION) after registration (Click here Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION) of the transmitter IDs into the tire pressure warning ECU and receiver after the ECU has been replaced.
When replacing the main body ECU (multiplex network body ECU), make sure to replace it with a new one.
w/o Stop and Start System:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Disconnect the tire pressure warning ECU and receiver M11*1 or M30*2 connector and main body ECU (multiplex network body ECU) G78 connector.
*1: for Air Bag Caution Label with "9L" Identification Mark
*2: except Air Bag Caution Label with "9L" Identification Mark
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M11-4 (RDA) - G78-16 (RDA) | Always | Below 1 Ω |
| M11-4 (RDA) or G78-16 (RDA) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M30-4 (RDA2) - G78-16 (RDA) | Always | Below 1 Ω |
| M30-4 (RDA2) or G78-16 (RDA) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the tire pressure warning ECU and receiver M11*1 or M30*2 connector.
*1: for Air Bag Caution Label with "9L" Identification Mark
*2: except Air Bag Caution Label with "9L" Identification Mark
| *A | for Air Bag Caution Label with "9L" Identification Mark |
| *B | except Air Bag Caution Label with "9L" Identification Mark |
| *a | Front view of wire harness connector
(to Tire Pressure Warning ECU and Receiver) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M11-12 (E) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M30-12 (GND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| M11-1 (IG) - Body ground | Ignition switch ON | 10 to 16 V |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| M30-1 (IG) - Body ground | Ignition switch ON | 10 to 16 V |
| Proceed to |
|---|
| OK |
| NG (w/o Stop and Start System) |
| NG (w/ Stop and Start System) |
OK
NG (w/o Stop and Start System)
NG (w/ Stop and Start System)
for 2WW: Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 2WW)>Backup Boost Converter Circuit
for 3ZR-FAE: Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>Backup Boost Converter Circuit
Replace the tire pressure warning ECU and receiver.
Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING RECEIVER>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Turn the ignition switch to ON.
Check for DTCs.
Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>DTC CHECK / CLEAR
DTC B1247 is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL