Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM(for 2WW) › from 2015.10
RM3090E _51 Engine / Hybrid System _009049 STOP AND START _0208733 STOP AND START SYSTEM(for 2WW) J

STOP AND START  STOP AND START SYSTEM(for 2WW)  Backup Boost Converter Circuit  


DESCRIPTION

A backup boost converter is built into the engine stop and start ECU. The backup boost converter helps maintain the power source voltage when the engine is restarted by stop and start control.

This prevents various functions such as the audio and visual system or navigation system from failing if the power source voltage drops due to the battery voltage dropping when the engine is restarted by stop and start control. If a DTC is output, troubleshoot the DTC first.

HINT:

A relay function and fuse function are provided in the backup boost converter.

If there is a malfunction in any of the electrical system circuits connected to the backup boost converter, the fuse and relay functions shut off the malfunctioning circuit to protect other circuits (remains shut off until next trip).

When the electrical system circuit is shut off, power to the circuit is cut off, causing any systems connected to the circuit to be disabled.

The fuse function is reset* when the ignition switch is turned off. If the malfunction still exists in the electrical system circuit that has been shut off by the relay function, it will be shut off again by the relay and fuse functions the next time the ignition switch is turned to ON.

*: A semiconductor fuse self-resets according to electric signals.

The backup boost converter supplies power to:
·

Main body ECU (multiplex network body ECU)

·

Skid control ECU (Brake actuator assembly)

·

Spiral with sensor cable sub-assembly

·

Power steering ECU assembly

·

Combination meter assembly

·

Radio receiver assembly, radio and display receiver assembly or navigation receiver assembly

·

Inner rear view mirror assembly

·

Lane departure warning camera

·

Tire pressure warning ECU and receiver

·

Blind spot monitor sensor LH

·

Blind spot monitor sensor RH

·

Parking assist ECU

·

Driving support ECU assembly

·

Millimeter wave radar sensor assembly

·

Network Gateway ECU



CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the engine stop and start ECU, read the number of starter operations and write it into a new engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 2WW)>REGISTRATION

·

After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 2WW)>REGISTRATION

·

After replacing the engine stop and start ECU or airbag sensor assembly, clear and calibrate the deceleration sensor zero point in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 2WW)>REGISTRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK PROBLEM SYMPTOMS
a.

Determine the trouble area by referring to the table below.

Effect on Vehicle Trouble Area/Cause Fail-safe DTC Output Stop and start cancel indicator light Symptom Proceed to
When the engine is restarted by stop and start control, the following symptoms may occur.
·

The audio and visual system or navigation system is reset

·

The combination meter assembly fades out

·

The steering wheel feels heavy when the engine is restarted*

*: A DTC may be stored in the power steering system


Backup boost converter internal malfunction
·

Internal power source malfunction

·

Internal power source overvoltage

·

Duty error

·

Communication cycle error


Stop and start control prohibited P323B Blinks Converter output voltage cannot be boosted when the engine is restarted A
Battery voltage drop
Systems on the converter output side do not operate
B41 terminal:
·

Parking assist ECU


B42 terminal: All of the following will not operate
·

Radio receiver assembly

·

Navigation receiver assembly

·

Radio and display receiver assembly


IG41 terminal: All of the following will not operate
·

Inner rear view mirror assembly

·

Lane departure warning camera

·

Tire pressure warning ECU and receiver

·

Blind spot monitor sensor LH

·

Blind spot monitor sensor RH

·

Network gateway ECU

·

Millimeter wave radar sensor assembly

·

Driving support ECU assembly

·

Parking assist ECU

·

Systems whose power is supplied from the main body ECU (multiplex network body ECU)


Overcurrent applied to an output terminal (output terminal relay circuit is shutoff) Stop and start control is prohibited
(Connected ECUs or sensors may detect power source malfunction DTCs)
B22C0 Blinks Systems do not operate as power supply from the converter is cut off A
Systems do not operate
(Due to converter input side malfunction)
IG1 terminal: All of the following do not operate
·

Brake actuator assembly

·

Spiral with sensor cable sub-assembly

·

Power steering ECU assembly

·

Inner rear view mirror assembly

·

Lane departure warning camera

·

Tire pressure warning ECU and receiver

·

Blind spot monitor sensor LH

·

Blind spot monitor sensor RH

·

Network gateway ECU

·

Millimeter wave radar sensor assembly

·

Driving support ECU assembly

·

Systems whose power is supplied from the main body ECU (multiplex network body ECU)


IG2 terminal:
·

The combination meter assembly will not function


ACC terminal: All of the following will not operate
·

Radio receiver assembly

·

Navigation receiver assembly

·

Radio and display receiver assembly

·

Parking assist ECU


Converter input circuit malfunction
·

Open or short to GND in IG1 circuit

·

Open or short to GND in IG2 circuit

·

Open or short to GND in ACC circuit


Stop and start control prohibited - Does not blink (Blinks when communication error DTCs are stored) Systems do not operate as power supply from the converter is cut off B
Systems on the converter output side do not operate
(varies depending on the malfunctioning relay circuit the converter detected)
AC41 terminal:
·

The radio receiver assembly will not function

·

The navigation receiver assembly will not function

·

The radio and display receiver assembly will not function

·

The parking assist ECU will not function


IG11 terminal:
·

The power steering ECU assembly will not function


IG12 terminal:
·

The combination meter assembly will not function


IG31 terminal:
·

The brake actuator assembly will not function

·

The spiral with sensor cable sub-assembly will not function


Malfunction in circuits the converter supplies power to
(between the converter and ECUs or sensors)
·

Open or short in the combination meter assembly circuit


Related systems do not operate as the relay circuit in the converter is turned off - Does not blink (Blinks when communication error DTCs are stored) Systems do not operate as power supply from the converter is cut off B
All of the following will operate
·

Inner rear view mirror assembly

·

Lane departure warning camera

·

Tire pressure warning ECU and receiver

·

Blind spot monitor sensor LH

·

Blind spot monitor sensor RH

·

Network gateway ECU

·

Millimeter wave radar sensor assembly

·

Driving support ECU assembly

·

Parking assist ECU

·

Systems whose power is supplied from the main body ECU (multiplex network body ECU)


·

Open in BBC fuse circuit

·

Short in converter circuit

·

Backup boost converter malfunction

·

Radio receiver assembly

·

Navigation receiverassembly

·

Radio and display receiver assembly


Stop and start control prohibited P0617 Does not blink (Due to disabled meter/gauge system) All systems that the converter supplies power to do not operate (see circuit diagram) A
P323B
The audio and visual system or navigation system does not function
(until the ignition switch is turned off)
Excessive audio volume
Data List item "State of BBC" displays "BBC Overcurrent" while the circuit is protected
The relay circuit in the converter is turned off to cut off power supply to the audio and visual system or navigation system (Returns to normal when the ignition switch is turned off) - Does not blink If overcurrent is detected in the audio and visual system or navigation system, system operation is disabled while the ignition switch is ON
(Returns to normal when the ignition switch is turned off)
C
·

The radio receiver assembly, navigation receiver assembly, radio and display receiver assembly or parking assist ECU cannot be turned off (short between AC41 and +B)

·

The combination meter assembly cannot be turned off (short between IG12 and +B)

·

Communication error DTCs may be stored due to short between IG31 and +B


HINT:

Varies depending on the number of times an open occurs in the +B circuit


Converter circuit malfunction
·

Short between AC41 and +B

·

Short between IG12 and +B

·

Short between IG31 and +B


- - Does not blink The converter cannot shut off power source when the ignition switch is turned off B
Ignition switch does not turn to ACC (short between ACC and +B)
Ignition switch does not turn off (short between IG1 or IG2 and +B)
Engine stop and start ECU power source circuit malfunction
·

Short between ACC and +B

·

Short between IG1 and +B

·

Short between IG2 and +B


- - Does not blink
·

Ignition switch does not turn to ACC

·

Ignition switch does not turn off


B


Result:
Proceed to
A
B
C



A

B

2.CHECK ENGINE STOP AND START ECU (POWER SOURCE CIRCUIT)

C

5.CHECK AUDIO AND VISUAL SYSTEM OR NAVIGATION SYSTEM
2.CHECK ENGINE STOP AND START ECU (POWER SOURCE CIRCUIT)
a.
A348177C24
0.229,1.302 0.615,1.615 0.385,0.313 0.135,3.323 0.521,3.635 0.385,0.313 2.219,4.188 1.948,3.771 true 0.802,2.042 1.219,1.5 true 1.49,2.063 1.229,1.698 true 1.573,4.208 1.542,3.76 true 1.094,4.177 1.438,3.76 true 0.198,0.167 0.51,0.365 0.313,0.198 10 false *a 0.313,1.396 0.625,1.594 0.313,0.198 10 false A86 0.188,3.417 0.781,3.615 0.594,0.198 10 false G87 2.177,4.229 2.49,4.427 0.313,0.198 10 false IG1 0.646,2.083 0.99,2.302 0.344,0.219 10 false BIN2 1.354,2.083 1.698,2.302 0.344,0.219 10 false BIN1 0.979,4.219 1.292,4.417 0.313,0.198 10 false IG2 1.448,4.25 1.76,4.448 0.313,0.198 10 false ACC
*a Front view of wire harness connector
(to Engine Stop and Start ECU)


Disconnect the engine stop and start ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A86-1 (BIN2) - Body ground Always 9.5 to 14 V
A86-3 (BIN1) - Body ground Always 9.5 to 14 V



c.

Turn the ignition switch ACC.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G87-19 (ACC) - Body ground Ignition switch ACC 9.5 to 14 V



e.

Turn the ignition switch to ON.


f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G87-18 (IG2) - Body ground Ignition switch ON 9.5 to 14 V
G87-21 (IG1) - Body ground Ignition switch ON 9.5 to 14 V



g.

Turn the ignition switch off.


h.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G87-18 (IG2) - Body ground Ignition switch off 0 to 1 V
G87-19 (ACC) - Body ground Ignition switch off 0 to 1 V
G87-21 (IG1) - Body ground Ignition switch off 0 to 1 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)
a.

Disconnect the connector from the corresponding system ECU/sensor.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Radio Receiver Assembly (for Radio Receiver Type)
Tester Connection Condition Specified Condition
G87-12 (B42) - G46-4 (+B1) Always Below 1 Ω
G87-24 (AC41) - G46-3 (ACC1) Always Below 1 Ω
G87-12 (B42) - Body ground Always 10 kΩ or higher
G87-24 (AC41) - Body ground Always 10 kΩ or higher
G46-4 (+B1) - Body ground Always 10 kΩ or higher
G46-3 (ACC1) - Body ground Always 10 kΩ or higher

Navigation Receiver Assembly (for Navigation Receiver Type)
Tester Connection Condition Specified Condition
G87-12 (B42) - G137-4 (+B1) Always Below 1 Ω
G87-24 (AC41) - G137-3 (ACC1) Always Below 1 Ω
G87-12 (B42) - Body ground Always 10 kΩ or higher
G87-24 (AC41) - Body ground Always 10 kΩ or higher
G137-4 (+B1) - Body ground Always 10 kΩ or higher
G137-3 (ACC1) - Body ground Always 10 kΩ or higher

Radio and Display Receiver Assembly (for Radio and Display Receiver Type)
Tester Connection Condition Specified Condition
G87-12 (B42) - G141-4 (+B1) Always Below 1 Ω
G87-24 (AC41) - G141-3 (ACC1) Always Below 1 Ω
G87-12 (B42) - Body ground Always 10 kΩ or higher
G87-24 (AC41) - Body ground Always 10 kΩ or higher
G141-4 (+B1) - Body ground Always 10 kΩ or higher
G141-3 (ACC1) - Body ground Always 10 kΩ or higher

Brake Actuator Assembly
Tester Connection Condition Specified Condition
G87-1 (IG31) - A80-12 (IG1) Always Below 1 Ω
G87-1 (IG31) - Body ground Always 10 kΩ or higher
A80-12 (IG1) - Body ground Always 10 kΩ or higher

Spiral with Sensor Cable Sub-assembly
Tester Connection Condition Specified Condition
G87-1 (IG31) - G12-4 (IG) Always Below 1 Ω
G87-1 (IG31) - Body ground Always 10 kΩ or higher
G12-4 (IG) - Body ground Always 10 kΩ or higher

Power Steering ECU Assembly
Tester Connection Condition Specified Condition
G87-6 (IG11) - h1-1 (IG) Always Below 1 Ω
G87-6 (IG11) - Body ground Always 10 kΩ or higher
h1-1 (IG) - Body ground Always 10 kΩ or higher

Combination Meter Assembly
Tester Connection Condition Specified Condition
G87-10 (IG12) - G16-39 (IG+) Always Below 1 Ω
G87-10 (IG12) - Body ground Always 10 kΩ or higher
G16-39 (IG+) - Body ground Always 10 kΩ or higher

Instrument Panel Junction Block Assembly (Main Body ECU (Multiplex Network Body ECU))
Tester Connection Condition Specified Condition
G87-3 (IG41) - 3D-40 (IG) Always Below 1 Ω
G87-3 (IG41) - Body ground Always 10 kΩ or higher
3D-40 (IG) - Body ground Always 10 kΩ or higher

Inner Rear View Mirror Assembly (w/ EC mirror without Lane Departure Alert System)
Tester Connection Condition Specified Condition
G87-3 (IG41) - Q14-1 (IG) Always Below 1 Ω
G87-3 (IG41) - Body ground Always 10 kΩ or higher
Q14-1 (IG) - Body ground Always 10 kΩ or higher

Inner Rear View Mirror Assembly (w/ EC mirror with Lane Departure Alert System)
Tester Connection Condition Specified Condition
G87-3 (IG41) - Q15-4 (IG) Always Below 1 Ω
G87-3 (IG41) - Body ground Always 10 kΩ or higher
Q15-4 (IG) - Body ground Always 10 kΩ or higher

Lane Departure Warning Camera (w/ Lane Departure Alert System)
Tester Connection Condition Specified Condition
G87-3 (IG41) - Q17-7 (IGB) Always Below 1 Ω
G87-3 (IG41) - Body ground Always 10 kΩ or higher
Q17-7 (IGB) - Body ground Always 10 kΩ or higher

Tire Pressure Warning ECU and Receiver (w/ Tire Pressure Warning System)
Tester Connection Condition Specified Condition
G87-3 (IG41) - M30-1 (IG) Always Below 1 Ω
G87-3 (IG41) - Body ground Always 10 kΩ or higher
M30-1 (IG) - Body ground Always 10 kΩ or higher

Blind Spot Monitor Sensor LH (w/ Blind Spot Monitor System)
Tester Connection Condition Specified Condition
G87-3 (IG41) - R1-5 (BLB) Always Below 1 Ω
G87-3 (IG41) - Body ground Always 10 kΩ or higher
R1-5 (BLB) - Body ground Always 10 kΩ or higher

Blind Spot Monitor Sensor RH (w/ Blind Spot Monitor System)
Tester Connection Condition Specified Condition
G87-3 (IG41) - T1-5 (BRB) Always Below 1 Ω
G87-3 (IG41) - Body ground Always 10 kΩ or higher
T1-5 (BRB) - Body ground Always 10 kΩ or higher

Network Gateway ECU
Tester Connection Condition Specified Condition
G87-3 (IG41) - G170-11 (IG1) Always Below 1 Ω
G87-3 (IG41) - Body ground Always 10 kΩ or higher
G170-11 (IG1) - Body ground Always 10 kΩ or higher

Millimeter Wave Radar Sensor Assembly (w/ Dynamic Radar Cruise Control System)
Tester Connection Condition Specified Condition
G87-3 (IG41) - Z6-8 (IGB) Always Below 1 Ω
G87-3 (IG41) - Body ground Always 10 kΩ or higher
Z6-8 (IGB) - Body ground Always 10 kΩ or higher

Driving Support ECU Assembly (w/ Dynamic Radar Cruise Control System)
Tester Connection Condition Specified Condition
G87-3 (IG41) - G168-7 (B) Always Below 1 Ω
G87-3 (IG41) - Body ground Always 10 kΩ or higher
G168-7 (B) - Body ground Always 10 kΩ or higher

Parking Assist ECU (w/ Panoramic View Monitor System)
Tester Connection Condition Specified Condition
G87-3 (IG41) - a2-6 (IG) Always Below 1 Ω
G87-24 (AC41) - a2-1 (ACC) Always Below 1 Ω
G87-2 (B41) - a2-2 (+B) Always Below 1 Ω
G87-3 (IG41) - Body ground Always 10 kΩ or higher
a2-6 (IG) - Body ground Always 10 kΩ or higher
G87-24 (AC41) - Body ground Always 10 kΩ or higher
a2-1 (ACC) - Body ground Always 10 kΩ or higher
G87-2 (B41) - Body ground Always 10 kΩ or higher
a2-2 (+B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK ENGINE STOP AND START ECU (EACH ECU OR SENSOR POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK ENGINE STOP AND START ECU (EACH ECU OR SENSOR POWER SOURCE CIRCUIT)
a.

Disconnect the connector from the corresponding system ECU/sensor.


b.

Measure the voltage according to the value(s) in the table below.

HINT:

Measure the voltage at the corresponding terminals.


Standard Voltage:
Radio Receiver Assembly (for Radio Receiver Type)
Tester Connection Condition Specified Condition
G46-4 (+B1) - Body ground Always 10.5 to 16 V

Navigation Receiver Assembly (for Navigation Receiver Type)
Tester Connection Condition Specified Condition
G137-4 (+B1) - Body ground Always 10.5 to 16 V

Radio and Display Receiver Assembly (for Radio and Display Receiver Type)
Tester Connection Condition Specified Condition
G141-4 (+B1) - Body ground Always 10.5 to 16 V

Parking Assist ECU (w/ Panoramic View Monitor System)
Tester Connection Condition Specified Condition
a2-2 (+B) - Body ground Always 10.5 to 16 V



c.

Turn the ignition switch to ACC.


d.

Measure the voltage according to the value(s) in the table below.

HINT:

Measure the voltage at the corresponding terminals.


Standard Voltage:
Radio Receiver Assembly (for Radio Receiver Type)
Tester Connection Switch Condition Specified Condition
G46-3 (ACC1) - Body ground Ignition switch ACC 10.5 to 16 V

Navigation Receiver Assembly (for Navigation Receiver Type)
Tester Connection Switch Condition Specified Condition
G137-3 (ACC1) - Body ground Ignition switch ACC 10.5 to 16 V

Radio and Display Receiver Assembly (for Radio and Display Receiver Type)
Tester Connection Switch Condition Specified Condition
G141-3 (ACC1) - Body ground Ignition switch ACC 10.5 to 16 V

Parking Assist ECU (w/ Panoramic View Monitor System)
Tester Connection Condition Specified Condition
a2-1 (ACC) - Body ground Ignition switch ACC 10.5 to 16 V



e.

Turn the ignition switch to ON.


f.

Measure the voltage according to the value(s) in the table below.

HINT:

Measure the voltage at the corresponding terminals.


Standard Voltage:
Tester Connection Switch Condition Specified Condition
3D-40 (IG) - Body ground Ignition switch ON 10.5 to 16 V
Q14-1 (IG) - Body ground*1 Ignition switch ON 10.5 to 16 V
Q15-1 (IG) - Body ground*2 Ignition switch ON 10.5 to 16 V
M30-1 (IG) - Body ground*3 Ignition switch ON 10.5 to 16 V
G170-11 (IG1) - Body ground Ignition switch ON 10.5 to 16 V
Z6-8 (IGB) - Body ground*4 Ignition switch ON 10.5 to 16 V
G168-7 (B) - Body ground*4 Ignition switch ON 10.5 to 16 V
Q17-7 (IGB) - Body ground*5 Ignition switch ON 10.5 to 16 V
R1-5 (BLB) - Body ground*6 Ignition switch ON 10.5 to 16 V
T1-5 (BRB) - Body ground*6 Ignition switch ON 10.5 to 16 V
a2-6 (IG) - Body ground*7 Ignition switch ON 10.5 to 16 V
G16-39 (IG+) - Body ground Ignition switch ON 10.5 to 16 V
h1-1 (IG) - Body ground Ignition switch ON 10.5 to 16 V
A80-12 (IG1) - Body ground Ignition switch ON 10.5 to 16 V
G12-4 (IG) - Body ground Ignition switch ON 10.5 to 16 V


*1: w/ EC Mirror without Lane Departure Alert System

*2: w/ EC Mirror with Lane Departure Alert System

*3: w/ Tire Pressure Warning System

*4: w/ Dynamic Radar Cruise Control System

*5: w/ Lane Departure Alert System

*6: w/ Blind Spot Monitor System

*7: w/ Panoramic View Monitor System



Result:
Proceed to
OK
NG



OK

CHECK POWER SOURCE CIRCUIT (POWER SOURCE CIRCUIT OF RELATED SYSTEM)

NG

5.CHECK AUDIO AND VISUAL SYSTEM OR NAVIGATION SYSTEM
a.

Turn the ignition switch off and wait for 1 minute.


b.

Turn the ignition switch to ON.


c.

Lower the audio volume.


d.

for Radio Receiver Type/Radio and Display Receiver Type:

Check if the audio and visual system operates normally.

OK:

Audio and visual system operates normally.



e.

for Navigation Receiver Type:

Check if the navigation system operates normally.

OK:

Navigation system operates normally.



Result:
Proceed to
NG
OK



NG

6.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - RADIO AND DISPLAY RECEIVER)

OK

END

6.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - RADIO AND DISPLAY RECEIVER)
a.

Disconnect the G87 engine stop and start ECU connector.


b.

for Radio Receiver Type:

Disconnect the G46 radio receiver assembly connector.


c.

for Navigation Receiver Type:

Disconnect the G137 navigation receiver assembly connector.


d.

for Radio and Display Receiver Type:

Disconnect the G141 radio and display receiver assembly connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for Radio Receiver Type:
Tester Connection Condition Specified Condition
G87-12 (B42) - Body ground Always 10 kΩ or higher
G46-4 (+B1) - Body ground Always 10 kΩ or higher
G87-24 (AC41) - Body ground Always 10 kΩ or higher
G46-3 (ACC1) - Body ground Always 10 kΩ or higher

for Navigation Receiver Type:
Tester Connection Condition Specified Condition
G87-12 (B42) - Body ground Always 10 kΩ or higher
G137-4 (+B1) - Body ground Always 10 kΩ or higher
G87-24 (AC41) - Body ground Always 10 kΩ or higher
G137-3 (ACC1) - Body ground Always 10 kΩ or higher

for Radio and Display Receiver Type:
Tester Connection Condition Specified Condition
G87-12 (B42) - Body ground Always 10 kΩ or higher
G141-4 (+B1) - Body ground Always 10 kΩ or higher
G87-24 (AC41) - Body ground Always 10 kΩ or higher
G141-3 (ACC1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK (for Radio Receiver Type/Radio and Display Receiver Type)
OK (for Navigation Receiver Type)
NG



OK (for Radio Receiver Type/Radio and Display Receiver Type)

OK (for Navigation Receiver Type)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR