Home › Vehicle Exterior › LIGHTING (EXT) › AUTOMATIC HIGH BEAM SYSTEM › from 2015.10
RM3090E _59 Vehicle Exterior _008430 LIGHTING (EXT) _0047055 AUTOMATIC HIGH BEAM SYSTEM U

LIGHTING (EXT)  AUTOMATIC HIGH BEAM SYSTEM  TERMINALS OF ECU  


CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY, MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


C278789N02
0.479,5.302 0.896,5.583 0.417,0.281 2.542,5.208 2.958,5.49 0.417,0.281 5.615,5.229 6.031,5.51 0.417,0.281 1.781,6.969 2.198,7.25 0.417,0.281 5.448,7.042 5.865,7.323 0.417,0.281 2.333,1.229 2.615,1.427 0.281,0.198 10 3B 3.01,0.938 3.292,1.135 0.281,0.198 10 3E 3.656,1.083 3.938,1.281 0.281,0.198 10 3C 4.344,1.208 4.625,1.406 0.281,0.198 10 3D 2.271,2.969 2.552,3.167 0.281,0.198 10 3A 0.604,5.365 0.885,5.563 0.281,0.198 10 3A 2.677,5.271 2.958,5.469 0.281,0.198 10 3B 5.729,5.292 6.01,5.49 0.281,0.198 10 3C 1.917,7.031 2.198,7.229 0.281,0.198 10 3D 5.573,7.104 5.854,7.302 0.281,0.198 10 3E

C278790C04
1.333,3.667 1.75,3.896 0.417,0.229 2.531,5.563 2.948,5.792 0.417,0.229 3.333,7.438 3.75,7.667 0.417,0.229 1.365,7.458 1.781,7.688 0.417,0.229 1.25,5.25 1.417,5.25 1.417,5.25 1.667,4.833 false 1.083,7.25 1.333,7.25 1.333,7.25 1.583,7 false 2.667,1.656 2.823,1.854 0.156,0.198 10 A 1.5,3.698 1.656,3.896 0.156,0.198 10 A 0.313,4.281 0.563,4.458 0.25,0.177 10 *A 1.083,5.167 1.333,5.344 0.25,0.177 10 *1 2.615,5.594 3.052,5.76 0.438,0.167 10 G78 3.406,7.469 3.865,7.635 0.458,0.167 10 G78 1.427,7.49 1.781,7.667 0.354,0.177 10 G79 0.917,7.167 1.167,7.344 0.25,0.177 10 *1 0.281,6.646 0.531,6.823 0.25,0.177 10 *B
*A Main Body ECU (Multiplex Network Body ECU) with 1 connector *B Main Body ECU (Multiplex Network Body ECU) with 3 connectors
*1 Main Body ECU (Multiplex Network Body ECU) - -


a.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

for LHD:

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL

for RHD:

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL


b.

Connect the instrument panel junction block assembly connectors.


c.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition

*1: w/o Stop and Start System

*2: w/ Stop and Start System

A-32 (IG) - Body ground - Ignition power supply Ignition switch ON 11 to 14 V*1
10.5 to 14 V*2
Ignition switch off Below 1 V
A-30 (BECU) - Body ground - Battery power supply Always 11 to 14 V
A-29 (ACC) - Body ground - ACC power supply Ignition switch ACC 11 to 14 V
Ignition switch off Below 1 V
A-11 (GND1) - Body ground - Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction in the wire harness or instrument panel junction block assembly.


d.

e.

Measure the voltage and pulse according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition

*1: Main Body ECU (multiplex network body ECU) with 3 Connectors

*2: Main Body ECU (multiplex network body ECU) with 1 Connector

3B-54 (DIM) - Body ground LG - Body ground DIMMER relay drive output Headlight dimmer switch in high or high flash position Below 1 V
Headlight dimmer switch not in high or high flash position 11 to 14 V
G78-5 (HU) - Body ground Y - Body ground Headlight dimmer switch high signal input Headlight dimmer switch in high position Below 1 V
Headlight dimmer switch in low position Pulse generation*1
11 to 14 V*2
G78-20 (CLTB) - G78-22 (CLTE) W - V Automatic light control sensor power supply output Ignition switch off Below 1 V
Ignition switch ON
Headlight dimmer switch in AUTO position
11 to 14 V
G78-21 (CLTS) - Body ground G - Body ground Automatic light control sensor signal input Ignition switch off Below 1 V
Ignition switch ON
Headlight dimmer switch in AUTO position
Automatic light control sensor covered with a hand → Automatic light control sensor exposed to ambient light
Pulse generation (See waveform 1)
G78-28 (A) - Body ground G - Body ground Headlight dimmer switch AUTO position signal input Headlight dimmer switch in AUTO position Below 1 V
Headlight dimmer switch not in AUTO position Pulse generation*1
11 to 14 V*2

i.
B113714E01
2.948,1.063 3.292,1.219 0.344,0.156 10 GND 1.844,1.177 1.969,1.333 0.125,0.156 10 A

Waveform 1

Item Content
Terminal No. (Symbol) G78-21 (CLTS) - Body ground
Tool setting 5 V/DIV., 5 ms./DIV.
Condition Ignition switch ON
Headlight dimmer switch in AUTO position
Automatic light control sensor covered with a hand → Automatic light control sensor exposed to ambient light

HINT:

If the ambient light becomes brighter, width A becomes narrower.





CHECK FORWARD RECOGNITION CAMERA