Home › Drivetrain › K111 MULTIDRIVE / CVT › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › from 2015.10
RM3090E _52 Drivetrain _008435 K111 MULTIDRIVE / CVT _0060958 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K111 MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P1585  Acceleration Sensor Circuit  


DESCRIPTION

The ECM determines the vehicle inclination based on a signal from the yaw rate and acceleration sensor (airbag sensor assembly).

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P1585 Acceleration Sensor Circuit 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.

The ignition switch is ON.

2.

The output value of the yaw rate and acceleration sensor remains at -1.5 G or less, or 1.5 G or more for at least 1.2 seconds.

3.

0.5 seconds

4.

1 trip detection logic


1.

The ignition switch is ON.

2.

The power source voltage to the yaw rate and acceleration sensor remains at 4.4 V or less, or 5.6 V or higher for at least 1.2 seconds.

3.

0.5 seconds

4.

1 trip detection logic


1.

The ignition switch is ON.

2.

No signal from the yaw rate and acceleration sensor is detected 7 times or more.

3.

0.5 seconds

4.

1 trip detection logic


1.

The ignition switch is ON.

2.

With the vehicle stopped, the difference between GL1 and GL2 does not become less than 0.4 G within 60 seconds after exceeding 0.6 G.

3.

0.5 seconds

4.

1 trip detection logic


1.

The ignition switch is ON.

2.

A yaw rate and acceleration sensor power source voltage malfunction signal is received for at least 10 seconds with the vehicle speed at 3 km/h (1.8 mph) or more.

3.

0.5 seconds

4.

1 trip detection logic


·

Yaw rate and acceleration sensor (Airbag sensor assembly)

·

Skid control ECU (Brake actuator assembly)

·

CAN communication system


- DTC stored

WIRING DIAGRAM

C347476E01
1.323,1.479 3.417,1.865 2.094,0.385 10 false Skid Control ECU (Brake Actuator Assembly) 1.333,3.833 3.479,4.208 2.146,0.375 10 false Yaw Rate and Acceleration Sensor (Airbag Sensor Assembly) 5.823,3.698 6.281,3.896 0.458,0.198 10 false ECM 0.469,5.323 4.135,5.521 3.667,0.198 10 false : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:
·

Perform initialization when parts related to the continuously variable transaxle are replaced.

Click hereDrivetrain>K111 MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION

·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K111 MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR



HINT:

If a CAN communication DTC is output, perform troubleshooting for that DTC first.


PROCEDURE

1.CHECK DTC OUTPUT (CAN COMMUNICATION SYSTEM)

DTCs are not output

2.READ VALUE USING GTS (G SENSOR)

DTCs are output

2.READ VALUE USING GTS (G SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List.

Powertrain > Engine and ECT > Data List
Tester Display
G Sensor
50003 234 410
Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
G Sensor Converted output voltage of deceleration sensor min.: 0 V
max.: 79.998 V
Displays converted voltage of deceleration sensor
·

Vehicle on level ground: 2.31 V to 2.69 V

·

Decelerating: 1.88 V to 2.5 V

·

Accelerating: 2.5 V to 3.11 V

·

G sensor malfunction: Set to 1.87 V

·

Communication malfunction: Set to 1.87 V


-

e.

In accordance with the display on the GTS, read the Data List.

Result:
Result Proceed to
Data displayed is as specified under Normal Condition A
Data displayed is not as specified under Normal Condition B




A

REPLACE SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)

B

3.REPLACE YAW RATE AND ACCELERATION SENSOR (AIRBAG SENSOR ASSEMBLY)
3.REPLACE YAW RATE AND ACCELERATION SENSOR (AIRBAG SENSOR ASSEMBLY)
a.

Replace the yaw rate and acceleration sensor (airbag sensor assembly).

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>REMOVAL


Result:
Proceed to
NEXT



NEXT