The skid control ECU (brake actuator assembly) receives signals from the ECM via the CAN communication system.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1437 | Lost Communication with ECM | When the +BS terminal voltage is 10 V or more and the vehicle speed is 15 km/h (9 mph) or more, data cannot be sent to the ECM for 2 seconds or more. | ·
CAN communication system (skid control ECU to ECM) ·
Skid control ECU (brake actuator assembly) ·
ECM |
When replacing the skid control ECU (brake actuator assembly), perform zero point calibration.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION
Using the GTS, check for any momentary interruption in the wire harness and connector corresponding to the DTC.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| EFI Communication Open | EFI communication open detection | Normal or Error | Normal | Error: Momentary interruption |
| EFI Communication Invalid | ECM communication invalid detection | Normal or Error | Normal | Error: Invalid |
| Tester Display |
|---|
| EFI Communication Open |
| EFI Communication Invalid |
Normal (There are no momentary interruptions.)
Perform the above inspection before removing the sensor and connector.
| Proceed to |
|---|
| OK |
| NG (for LHD with Central Gateway ECU) |
| NG (for RHD with Central Gateway ECU) |
| NG (for LHD without Central Gateway ECU) |
| NG (for RHD without Central Gateway ECU) |
OK
NG (for LHD with Central Gateway ECU)
NG (for RHD with Central Gateway ECU)
NG (for LHD without Central Gateway ECU)
NG (for RHD without Central Gateway ECU)
Clear the DTCs.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Start the engine.
Drive the vehicle at a speed of 15 km/h (9 mph) or more for 10 seconds or more.
Check that no CAN communication system DTC is output.
for LHD with Central Gateway ECU: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU)>DIAGNOSIS SYSTEM
for RHD with Central Gateway ECU: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU)>DIAGNOSIS SYSTEM
for LHD without Central Gateway ECU: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD without Central Gateway ECU)>DIAGNOSIS SYSTEM
for RHD without Central Gateway ECU: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD without Central Gateway ECU)>DIAGNOSIS SYSTEM
Check if the same DTC is recorded.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| DTC C1437 is not output |
| DTC C1437 is output |
| NG (for LHD with Central Gateway ECU) |
| NG (for RHD with Central Gateway ECU) |
| NG (for LHD without Central Gateway ECU) |
| NG (for RHD without Central Gateway ECU) |
DTC C1437 is not output
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
DTC C1437 is output
NG (for LHD with Central Gateway ECU)
NG (for RHD with Central Gateway ECU)
NG (for LHD without Central Gateway ECU)
NG (for RHD without Central Gateway ECU)