The ECM of this system is connected to the CAN communication system. Therefore, before starting troubleshooting, be sure to check that there are no malfunctions in the CAN communication system.
*: Use the GTS.
| Proceed to |
|---|
| NEXT |
NEXT
Refer to How to Troubleshoot ECU Controlled Systems in Introduction.
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
| Proceed to |
|---|
| NEXT |
NEXT
11 to 14 V
If the voltage is below 11 V, recharge or replace the battery before proceeding.
| Proceed to |
|---|
| NEXT |
NEXT
Use the GTS to check if the CAN communication system is functioning normally.
Refer to CAN Bus Check for the CAN communication system.
for LHD with Central Gateway ECU:
for RHD with Central Gateway ECU:
for LHD without Central Gateway ECU:
for RHD without Central Gateway ECU:
The ECM is connected to the CAN communication system. Therefore, before starting troubleshooting, make sure to check that there are no malfunctions in the CAN communication system.
| Result | Proceed to |
|---|---|
| CAN communication DTCs are not output. | A |
| CAN communication DTCs are output. | B |
A
B
for LHD with Central Gateway ECU:
for RHD with Central Gateway ECU:
for LHD without Central Gateway ECU:
for RHD without Central Gateway ECU:
Refer to DTC Check/Clear.
Click hereDrivetrain>K114F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| NEXT |
NEXT
Refer to Check Mode Procedure.
Click hereDrivetrain>K114F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>CHECK MODE PROCEDURE
| Proceed to |
|---|
| NEXT |
NEXT
Proceed to DTC Check/Clear.
Click hereDrivetrain>K114F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTCs are not output. | A |
| DTCs are output. | B |
A
B
Refer to Continuously Variable Transaxle Fluid.
Click hereDrivetrain>K114F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE FLUID>ADJUSTMENT
Refer to Park/Neutral Position Switch.
Click hereDrivetrain>K114F MULTIDRIVE / CVT>PARK / NEUTRAL POSITION SWITCH>ON-VEHICLE INSPECTION
Refer to Shift Lever.
Click hereDrivetrain>K114F MULTIDRIVE / CVT>SHIFT LEVER>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Refer to Road Test.
Click hereDrivetrain>K114F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>ROAD TEST
Refer to Mechanical System Tests.
Click hereDrivetrain>K114F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>MECHANICAL SYSTEM TESTS
Refer to Hydraulic Test.
Click hereDrivetrain>K114F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>HYDRAULIC TEST
| Result | Proceed to |
|---|---|
| Symptom does not occur | A |
| Symptom occurs | B |
A
B
Refer to Symptom Simulation.
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT
Proceed to Diagnostic Trouble Code Chart.
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT