The ECM determines the vehicle inclination based on a signal from the yaw rate and acceleration sensor (airbag sensor assembly). If a malfunction in the yaw rate and acceleration sensor (airbag sensor assembly) is determined based on a malfunction signal from the skid control ECU (brake actuator assembly), the ECM stores this DTC.
The yaw rate and acceleration sensor (airbag sensor assembly) signal is sent to the skid control ECU (brake actuator assembly) via CAN communication.
If CAN communication DTCs are output, perform troubleshooting for those DTCs first.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P1585 | Acceleration Sensor Circuit | 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
DTC Detection Condition 1: 1.
The ignition switch is ON. 2.
The output value of the yaw rate and acceleration sensor (airbag sensor assembly) remains at -1.5 G or less, or 1.5 G or more for at least 1.2 seconds. 3.
0.5 seconds or more 4.
1-trip detection logic DTC Detection Condition 2: 1.
The ignition switch is ON. 2.
The power source voltage to the yaw rate and acceleration sensor (airbag sensor assembly) remains at 4.4 V or less, or 5.6 V or higher for 1.2 seconds or more. 3.
0.5 seconds or more 4.
1-trip detection logic DTC Detection Condition 3: 1.
The ignition switch is ON. 2.
No signal from the yaw rate and acceleration sensor (airbag sensor assembly) is detected 7 times or more. 3.
0.5 seconds or more 4.
1-trip detection logic DTC Detection Condition 4: 1.
The ignition switch is ON. 2.
With the vehicle stopped, the difference between GL1 and GL2 does not become less than 0.4 G within 60 seconds after exceeding 0.6 G. 3.
0.5 seconds or more 4.
1-trip detection logic DTC Detection Condition 5: 1.
The ignition switch is ON. 2.
A yaw rate and acceleration sensor (airbag sensor assembly) power source voltage malfunction signal is received for 10 seconds or more with the vehicle speed at 3 km/h (1.8 mph) or more. 3.
0.5 seconds or more 4.
1-trip detection logic |
·
Yaw rate and acceleration sensor (airbag sensor assembly) ·
Skid control ECU (Brake actuator assembly) ·
CAN communication system |
Does not come on | DTC stored |
Perform initialization when parts related to the continuously variable transaxle are replaced.
Click hereDrivetrain>K114F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION
Check that no DTCs are stored after performing initialization.
Click hereDrivetrain>K114F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC U0129 is not output | A |
| DTC U0129 is output | B |
A
B
for LHD with Central Gateway ECU:
for RHD with Central Gateway ECU:
for LHD without Central Gateway ECU:
for RHD without Central Gateway ECU:
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Primary.
In accordance with the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| G Sensor | Converted output voltage of G sensor | Min.: 0 V
Max.: 79.998 V |
Displays converted voltage of G sensor
·
2.31 V to 2.69 V: Vehicle on level ground ·
1.88 V to 2.5 V: Decelerating ·
2.5 V to 3.11 V: Accelerating ·
Set to 1.87 V: G sensor malfunction ·
Set to 1.87 V: Communication malfunction |
- |
| Tester Display |
|---|
| G Sensor |
| Result | Proceed to |
|---|---|
| Data display is not within Normal Condition range | A |
| Data display is within Normal Condition range | B |
A
B
Replace the yaw rate and acceleration sensor (airbag sensor assembly).
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT