Home › Engine / Hybrid System › 2AR-FE ENGINE CONTROL › SFI SYSTEM(w/ Canister Pump Module) › from 2015.10
RM3090E _51 Engine / Hybrid System _008378 2AR-FE ENGINE CONTROL _0060196 SFI SYSTEM(w/ Canister Pump Module) C

2AR-FE ENGINE CONTROL  SFI SYSTEM(w/ Canister Pump Module)  P0112  Intake Air Temperature Circuit Low Input  P0113  Intake Air Temperature Circuit High Input  


DESCRIPTION

A293042E01
3.323,2.188 3.74,1.771 false 2,0.51 3.073,0.708 1.073,0.198 10 Resistance 1.604,0.229 2.677,0.427 1.073,0.198 10 Fig. 1: 2.115,0.792 3.188,0.99 1.073,0.198 10 [kΩ] 2.208,0.99 2.531,1.188 0.323,0.198 10 30 2.208,1.156 3.281,1.354 1.073,0.198 10 20 2.208,1.438 3.281,1.635 1.073,0.198 10 10 2.281,1.719 3.354,1.917 1.073,0.198 10 5 2.281,1.938 3.354,2.135 1.073,0.198 10 3 2.281,2.104 3.354,2.302 1.073,0.198 10 2 2.271,2.365 3.344,2.563 1.073,0.198 10 1 2.167,2.677 2.667,2.917 0.5,0.24 10 0.5 2.167,2.865 3.24,3.063 1.073,0.198 10 0.3 2.156,3.042 3.229,3.24 1.073,0.198 10 0.2 2.156,3.313 3.229,3.51 1.073,0.198 10 0.1 2.458,3.708 3.531,3.906 1.073,0.198 10 -20 2.833,3.708 3.906,3.906 1.073,0.198 10 0 3.104,3.708 4.177,3.906 1.073,0.198 10 20 3.427,3.708 4.5,3.906 1.073,0.198 10 40 3.729,3.708 4.802,3.906 1.073,0.198 10 60 4.052,3.708 5.125,3.906 1.073,0.198 10 80 4.313,3.708 5.385,3.906 1.073,0.198 10 100 4.802,3.708 5.875,3.906 1.073,0.198 10 [°C] 2.5,3.958 3.573,4.156 1.073,0.198 10 -4 2.802,3.958 3.875,4.156 1.073,0.198 10 32 3.115,3.958 4.188,4.156 1.073,0.198 10 68 3.396,3.958 3.76,4.281 0.365,0.323 10 104 3.698,3.958 4.094,4.292 0.396,0.333 10 140 4.021,3.958 4.417,4.292 0.396,0.333 10 176 4.333,3.958 4.729,4.292 0.396,0.333 10 212 4.781,3.969 5.854,4.167 1.073,0.198 10 [°F] 2.854,4.281 3.927,4.479 1.073,0.198 10 Temperature 3.771,1.625 4.844,1.823 1.073,0.198 10 Acceptable

The intake air temperature sensor, mounted on the mass air flow meter sub-assembly, monitors the intake air temperature. The intake air temperature sensor has a built-in thermistor with a resistance that varies according to the temperature of the intake air. When the intake air temperature is low, the resistance of the thermistor increases. When the temperature is high, the resistance drops. These variations in resistance are transmitted to the ECM as voltage changes (See Fig. 1).

The intake air temperature sensor is powered by a 5 V supply from the THA terminal of the ECM, via resistor R.

Resistor R and the intake air temperature sensor are connected in series. When the resistance value of the intake air temperature sensor changes, according to changes in the intake air temperature, the voltage at terminal THA also varies. Based on this signal, the ECM increases the fuel injection volume when the engine is cold to improve driveability.

HINT:

When DTC P0112 or P0113 is stored, the ECM enters fail-safe mode. During fail-safe mode, the intake air temperature is estimated to be 20°C (68°F) by the ECM. Fail-safe mode continues until a pass condition is detected.



DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0112 Intake Air Temperature Circuit Low Input A short in the intake air temperature sensor circuit for 0.5 seconds (1 trip detection logic).
·

Short in intake air temperature sensor circuit

·

Intake air temperature sensor (built into mass air flow meter sub-assembly)

·

ECM


Comes on DTC stored
P0113 Intake Air Temperature Circuit High Input An open in the intake air temperature sensor circuit for 0.5 seconds (1 trip detection logic).
·

Open in intake air temperature sensor circuit

·

Intake air temperature sensor (built into mass air flow meter sub-assembly)

·

ECM


Comes on DTC stored

HINT:

When any of these DTCs are output, check the intake air temperature using the GTS. Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Intake Air.


Temperature Displayed Malfunction
-40°C (-40°F) Open circuit
Higher than 128°C (262°F) Short circuit

MONITOR DESCRIPTION

The ECM monitors the sensor voltage and uses this value to calculate the intake air temperature. When the sensor output voltage deviates from the normal operating range, the ECM interprets this as a malfunction in the intake air temperature sensor circuit and stores a DTC.

Example:

If the sensor output voltage is higher than 4.91 V for 0.5 seconds or more, the ECM determines that there is an open in the intake air temperature sensor circuit, and stores DTC P0113. Conversely, if the output voltage is less than 0.18 V for 0.5 seconds or more, the ECM determines that there is a short in the sensor circuit, and stores DTC P0112.

MONITOR STRATEGY

Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Turn the engine switch on (IG) and wait for 5 seconds or more.


WIRING DIAGRAM

A255126E54
0.219,2.729 0.5,2.917 0.281,0.188 10 B1 0.219,2.896 2.719,3.354 2.5,0.458 10 Intake Air Temperature Sensor (Built into Mass Air Flow Meter Sub-assembly) 1.604,1.479 2.073,1.792 0.469,0.313 10 THA 1.708,2.083 2.167,2.354 0.458,0.271 10 E2 1.99,1.49 2.188,1.74 0.198,0.25 10 1 1.99,2.083 2.219,2.292 0.229,0.208 10 2 5.406,1.479 5.75,1.75 0.344,0.271 10 THA 5.167,1.479 5.427,1.688 0.26,0.208 10 93 5.167,2.083 5.417,2.313 0.25,0.229 10 94 5.396,2.073 5.844,2.344 0.448,0.271 10 ETHA 5.99,1.354 6.177,1.563 0.188,0.208 10 R 6.01,1.073 6.354,1.281 0.344,0.208 10 5 V 6,3.104 6.448,3.344 0.448,0.24 10 ECM 5.667,3.104 6,3.333 0.333,0.229 10 B77

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (INTAKE AIR)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Intake Air.

Powertrain > Engine and ECT > Data List
Tester Display
Intake Air
50003 234 5

e.

Read the value displayed on the GTS.

OK:

Same as actual intake air temperature.


Result:
Result Proceed to
-40°C (-40°F) A
Higher than 128°C (262°F) B
Same as actual intake air temperature C


HINT:
·

If there is an open circuit, the GTS indicates -40°C (-40°F).

·

If there is a short circuit, the GTS indicates higher than 128°C (262°F).





A

2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)

B

4.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)

C

2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)
a.

Disconnect the mass air flow meter sub-assembly connector.

A257883C02
4.083,1.688 4.417,1.917 0.333,0.229 5.073,1.917 4.854,2.354 false 5.229,1.917 5.479,2.354 false 1.01,1.927 1.156,2.083 0.146,0.156 10 *1 1.365,1.458 1.552,1.615 0.188,0.156 10 E2 1.271,1.156 1.573,1.313 0.302,0.156 10 THA 2.531,1.458 2.927,1.615 0.396,0.156 10 ETHA 2.531,1.156 2.833,1.313 0.302,0.156 10 THA 2.833,1.927 2.979,2.083 0.146,0.156 10 *2 4.073,0.26 4.219,0.417 0.146,0.156 10 *a 4.656,2.365 4.958,2.521 0.302,0.156 10 THA 5.448,2.365 5.635,2.521 0.188,0.156 10 E2 4.167,1.719 4.49,1.917 0.323,0.198 10 B1
*1 Mass Air Flow Meter Sub-assembly *2 ECM
*a Front view of wire harness connector
(to Mass Air Flow Meter Sub-assembly)
- -



b.

Connect terminals 1 (THA) and 2 (E2) of the mass air flow meter sub-assembly connector on the wire harness side.


c.

Connect the GTS to the DLC3.


d.

Turn the engine switch on (IG).


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Intake Air.

Powertrain > Engine and ECT > Data List
Tester Display
Intake Air
50003 234 5

g.

Read the value displayed on the GTS.

Standard value:

Higher than 128°C (262°F)


HINT:

Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION



Result:
Proceed to
OK
NG



OK

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

NG

3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B1-1 (THA) - B77-93 (THA) Always Below 1 Ω
B1-2 (E2) - B77-94 (ETHA) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)
a.
A255925C03
0.662,0.158 0.817,0.312 0.155,0.154 10 *1 2.57,0.158 2.725,0.312 0.155,0.154 10 *2 2.226,0.805 2.525,0.958 0.299,0.154 10 THA 2.226,1.183 2.616,1.337 0.39,0.154 10 ETHA
*1 Mass Air Flow Meter Sub-assembly
*2 ECM


Disconnect the mass air flow meter sub-assembly connector.


b.

Connect the GTS to the DLC3.


c.

Turn the engine switch on (IG).


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Intake Air.

Powertrain > Engine and ECT > Data List
Tester Display
Intake Air
50003 234 5

f.

Read the value displayed on the GTS.

Standard value:

-40°C (-40°F)


HINT:

Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION



Result:
Proceed to
OK
NG



OK

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

NG

5.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
5.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B1-1 (THA) or B77-93 (THA) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR