Home › Engine / Hybrid System › 2AR-FE ENGINE CONTROL › SFI SYSTEM(w/ Canister Pump Module) › from 2015.10
RM3090E _51 Engine / Hybrid System _008378 2AR-FE ENGINE CONTROL _0060196 SFI SYSTEM(w/ Canister Pump Module) C

2AR-FE ENGINE CONTROL  SFI SYSTEM(w/ Canister Pump Module)  P0351  Ignition Coil "A" Primary / Secondary Circuit  P0352  Ignition Coil "B" Primary / Secondary Circuit  P0353  Ignition Coil "C" Primary / Secondary Circuit  P0354  Ignition Coil "D" Primary / Secondary Circuit  


DESCRIPTION

HINT:
·

These DTCs indicate malfunctions relating to the primary circuit.

·

If DTC P0351 is output, check the ignition coil assembly (No. 1 cylinder) circuit.

·

If DTC P0352 is output, check the ignition coil assembly (No. 2 cylinder) circuit.

·

If DTC P0353 is output, check the ignition coil assembly (No. 3 cylinder) circuit.

·

If DTC P0354 is output, check the ignition coil assembly (No. 4 cylinder) circuit.



A Direct Ignition System (DIS) is used on this vehicle.

The DIS is a 1-cylinder ignition system in which each cylinder is ignited by one ignition coil assembly and one spark plug is connected to the end of each secondary wiring. A powerful voltage, generated in the secondary wiring, is applied directly to each spark plug. The spark of the spark plugs passes from the center electrode to the ground electrodes.

The ECM determines the ignition timing and transmits the ignition (IGT) signals to each cylinder. Using the IGT signal, the ECM turns the power transistor inside the igniter on and off. The power transistor, in turn, switches the current supplied to the primary coil on and off. When the current to the primary coil is cut off, a powerful voltage is generated in the secondary coil. This voltage is applied to the spark plugs, causing them to spark inside the cylinders. As the ECM cuts the current to the primary coil, the igniter sends back an ignition confirmation (IGF) signal to the ECM for each cylinder ignition.

A255924E06
4.427,1.385 4.375,0.938 4.375,0.938 4.302,0.938 false 5.333,1.156 5.563,0.719 5.563,0.719 5.635,0.719 false 3.896,0.844 4.5,1 0.604,0.156 10 Igniter 4.51,0.479 5.323,0.656 0.813,0.177 10 from Battery 5.688,0.646 7.073,1.198 1.385,0.552 10 Ignition Coil Assembly (No. 1 Cylinder) 5.615,1.854 6.729,2.031 1.115,0.177 10 No. 1 Spark Plug 5.615,3.063 6.729,3.24 1.115,0.177 10 No. 2 Spark Plug 5.615,4.385 6.729,4.563 1.115,0.177 10 No. 3 Spark Plug 5.615,5.688 6.729,5.865 1.115,0.177 10 No. 4 Spark Plug 2.74,5.927 3.083,6.104 0.344,0.177 10 ECM 2.896,1.448 3.26,1.604 0.365,0.156 10 IGT1 2.885,1.75 3.26,1.896 0.375,0.146 10 IGF1 0.302,1.5 2.031,1.667 1.729,0.167 10 Crankshaft Position Sensor 0.313,3.292 2.042,3.458 1.729,0.167 10 Camshaft Position Sensor 2.885,2.76 3.25,2.917 0.365,0.156 10 IGT2 2.896,5.406 3.26,5.563 0.365,0.156 10 IGT4 2.875,4.094 3.24,4.25 0.365,0.156 10 IGT3 0.188,4.49 2.146,5.313 1.958,0.823 10 Other Sensors (Engine Coolant Temperature Sensor, Mass Air Flow Meter Sub-assembly, Throttle Position Sensor, etc.) 3.75,3.354 6.208,3.583 2.458,0.229 10 Ignition Coil Assembly (No. 2 Cylinder) 3.74,5.958 6.531,6.188 2.792,0.229 10 Ignition Coil Assembly (No. 4 Cylinder) 3.74,4.656 6.427,4.885 2.688,0.229 10 Ignition Coil Assembly (No. 3 Cylinder)

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0351 Ignition Coil "A" Primary / Secondary Circuit No IGF signal to the ECM while the engine is running (1 trip detection logic).
·

Ignition system

·

Open or short in IGF1 or IGT1 circuit between ignition coil assembly and ECM

·

No. 1 ignition coil assembly

·

ECM


Comes on DTC stored
P0352 Ignition Coil "B" Primary / Secondary Circuit No IGF signal to the ECM while the engine is running (1 trip detection logic).
·

Ignition system

·

Open or short in IGF1 or IGT2 circuit between ignition coil assembly and ECM

·

No. 2 ignition coil assembly

·

ECM


Comes on DTC stored
P0353 Ignition Coil "C" Primary / Secondary Circuit No IGF signal to the ECM while the engine is running (1 trip detection logic).
·

Ignition system

·

Open or short in IGF1 or IGT3 circuit between ignition coil assembly and ECM

·

No. 3 ignition coil assembly

·

ECM


Comes on DTC stored
P0354 Ignition Coil "D" Primary / Secondary Circuit No IGF signal to the ECM while the engine is running (1 trip detection logic).
·

Ignition system

·

Open or short in IGF1 or IGT4 circuit between ignition coil assembly and ECM

·

No. 4 ignition coil assembly

·

ECM


Comes on DTC stored

Reference: Inspection using an oscilloscope.

A299080E03
0.365,1.75 0.698,1.938 0.333,0.188 10 false IGF 0.365,1.427 0.698,1.615 0.333,0.188 10 false IGT 3.021,1.521 3.354,1.708 0.333,0.188 10 false GND 3.021,2.177 3.354,2.365 0.333,0.188 10 false GND 2.76,0.771 3.354,0.979 0.594,0.208 10 false 2 V/DIV. 1.552,2.594 2.333,2.813 0.781,0.219 10 false 20 ms./DIV.


While idling the engine, check the waveform between terminals IGT (1 to 4) and E1, and IGF1 and E1 of the ECM connector.

ECM Terminal Name IGT: Between IGT (1 to 4) and E1
IGF: Between IGF1 and E1
Tester Range 2 V/DIV., 20 ms./DIV.
Condition Idling


MONITOR DESCRIPTION

A212405E23
1.802,1.677 2.198,1.854 0.396,0.177 10 ECM 2.99,1.302 3.26,1.49 0.271,0.188 10 IGT 2.979,1.729 3.26,1.885 0.281,0.156 10 IGF 4.156,1.51 4.594,1.656 0.438,0.146 10 Igniter 5.396,1.385 6.167,1.563 0.771,0.177 10 Ignition Coil 4.427,2.365 6.104,2.552 1.677,0.188 10 Ignition Coil Assembly 0.24,3.115 1.177,3.448 0.938,0.333 10 Ignition Signal (IGT) 1.677,3.573 2.167,3.76 0.49,0.188 10 Normal 1.417,3.969 2.188,4.156 0.771,0.188 10 Malfunction 0.052,3.875 1.365,4.344 1.313,0.469 10 Ignition Confirmation Signal (IGF1) 3.604,4.51 4.458,4.688 0.854,0.177 10 Circuit Open 5.948,4.969 6.313,5.167 0.365,0.198 10 Time

If the ECM does not receive any IGF1 signals despite transmitting the IGT signal, it interprets this as a fault in the igniter and stores a DTC.

MONITOR STRATEGY

Required Sensors/Components (Main) Igniter
Required Sensors/Components (Related) Crankshaft position sensor
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Start the engine and run it at idle for 10 seconds or more.


WIRING DIAGRAM

A371211E01
0.531,5.573 1.604,5.771 1.073,0.198 10 false Battery 0.354,4.781 1.427,4.979 1.073,0.198 10 false FL MAIN 0.646,0.917 1.031,1.104 0.385,0.188 10 false IG2 1.688,1.594 2.073,1.781 0.385,0.188 10 false IG2 1.865,2.76 2.25,2.948 0.385,0.188 10 false IG2D 1.406,3.313 1.792,3.5 0.385,0.188 10 false G82 1.417,3.51 2.969,3.854 1.552,0.344 10 false Certification ECU (Smart Key ECU Assembly) 3.75,0.885 4.135,1.073 0.385,0.188 10 false 1 1.396,1.385 1.781,1.573 0.385,0.188 10 false 2 5.635,0.885 6.021,1.073 0.385,0.188 10 false 57 2.177,0.875 2.563,1.063 0.385,0.188 10 false 5 2.271,2.875 2.656,3.063 0.385,0.188 10 false 9 1.406,0.875 1.792,1.063 0.385,0.188 10 false 3 3.75,2.479 4.135,2.667 0.385,0.188 10 false 1 3.76,4.083 4.146,4.271 0.385,0.188 10 false 1 3.771,5.615 4.156,5.802 0.385,0.188 10 false 1 3.76,1.198 4.146,1.385 0.385,0.188 10 false 4 3.75,2.802 4.135,2.99 0.385,0.188 10 false 4 3.75,4.385 4.135,4.573 0.385,0.188 10 false 4 3.76,5.99 4.146,6.177 0.385,0.188 10 false 4 4.948,0.885 5.333,1.073 0.385,0.188 10 false 3 4.948,2.5 5.333,2.688 0.385,0.188 10 false 3 4.948,4.083 5.333,4.271 0.385,0.188 10 false 3 4.948,5.615 5.333,5.802 0.385,0.188 10 false 3 4.958,1.188 5.344,1.354 0.385,0.167 10 false 2 4.958,2.813 5.344,2.979 0.385,0.167 10 false 2 4.958,4.406 5.344,4.573 0.385,0.167 10 false 2 4.958,6.01 5.344,6.177 0.385,0.167 10 false 2 2.177,1.396 2.563,1.583 0.385,0.188 10 false 1 5.635,2.5 6.021,2.688 0.385,0.188 10 false 56 5.625,4.094 6.01,4.281 0.385,0.188 10 false 55 5.635,5.615 6.021,5.802 0.385,0.188 10 false 54 5.635,6.021 6.021,6.208 0.385,0.188 10 false 51 5.896,0.896 6.563,1.083 0.667,0.188 10 false IGT1 5.896,2.521 6.563,2.708 0.667,0.188 10 false IGT2 5.885,4.104 6.552,4.292 0.667,0.188 10 false IGT3 5.885,5.625 6.552,5.813 0.667,0.188 10 false IGT4 5.99,6 6.656,6.188 0.667,0.188 10 false IGF1 3.927,0.771 4.594,0.958 0.667,0.188 10 false +B 3.917,1.083 4.583,1.271 0.667,0.188 10 false GND 4.583,0.75 5.25,0.938 0.667,0.188 10 false IGT1 4.625,1.083 5.292,1.271 0.667,0.188 10 false IGF 3.656,1.479 4.323,1.667 0.667,0.188 10 false B100 3.656,1.667 5.615,1.896 1.958,0.229 10 false No. 1 Ignition Coil Assembly 3.938,2.365 4.604,2.552 0.667,0.188 10 false +B 3.927,3.958 4.594,4.146 0.667,0.188 10 false +B 3.927,5.49 4.594,5.677 0.667,0.188 10 false +B 3.927,2.698 4.594,2.885 0.667,0.188 10 false GND 3.927,4.281 4.594,4.469 0.667,0.188 10 false GND 3.917,5.885 4.583,6.073 0.667,0.188 10 false GND 4.594,2.385 5.26,2.573 0.667,0.188 10 false IGT2 4.573,3.979 5.24,4.167 0.667,0.188 10 false IGT3 4.573,5.49 5.24,5.677 0.667,0.188 10 false IGT4 4.656,2.688 5.323,2.875 0.667,0.188 10 false IGF 4.656,4.292 5.323,4.479 0.667,0.188 10 false IGF 4.646,5.896 5.313,6.083 0.667,0.188 10 false IGF 6.135,6.438 6.802,6.625 0.667,0.188 10 false ECM 6.135,6.271 6.802,6.458 0.667,0.188 10 false B77 3.615,3.083 4.281,3.271 0.667,0.188 10 false B99 3.635,4.688 4.302,4.875 0.667,0.188 10 false B98 3.667,6.281 4.333,6.469 0.667,0.188 10 false B97 3.625,3.25 5.583,3.479 1.958,0.229 10 false No. 2 Ignition Coil Assembly 3.646,4.844 5.604,5.073 1.958,0.229 10 false No. 3 Ignition Coil Assembly 3.667,6.427 5.625,6.656 1.958,0.229 10 false No. 4 Ignition Coil Assembly

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - BODY GROUND)
a.

Disconnect the ignition coil assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B100-4 (GND) - Body ground Always Below 1 Ω
B99-4 (GND) - Body ground Always Below 1 Ω
B98-4 (GND) - Body ground Always Below 1 Ω
B97-4 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF IGNITION COIL ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF IGNITION COIL ASSEMBLY)
a.
A337498C05
0.26,0.396 0.75,0.656 0.49,0.26 0.26,0.75 0.76,1 0.5,0.25 0.26,1.104 0.76,1.354 0.5,0.25 0.26,1.438 0.771,1.677 0.51,0.24 0.906,1.781 1.219,1.156 true 2.417,1.802 2.25,1.198 true 0.063,0.083 0.375,0.24 0.313,0.156 10 false *a 0.385,0.802 0.698,0.958 0.313,0.156 10 false B99 0.344,0.448 0.844,0.719 0.5,0.271 10 false B100 0.396,1.146 0.708,1.302 0.313,0.156 10 false B98 0.406,1.479 0.719,1.677 0.313,0.198 10 false B97 0.802,1.823 1.115,2.021 0.313,0.198 10 false +B 2.302,1.844 2.615,2.042 0.313,0.198 10 false GND
*a Front view of wire harness connector
(to Ignition Coil Assembly)


Disconnect the ignition coil assembly connectors.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B100-1 (+B) - B100-4 (GND) Engine switch on (IG) 11 to 14 V
B99-1 (+B) - B99-4 (GND) Engine switch on (IG) 11 to 14 V
B98-1 (+B) - B98-4 (GND) Engine switch on (IG) 11 to 14 V
B97-1 (+B) - B97-4 (GND) Engine switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM)

NG

5.CHECK HARNESS AND CONNECTOR (IG2 RELAY - IGNITION COIL ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM)
a.

Disconnect the ignition coil assembly connectors.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B100-2 (IGF) - B77-51 (IGF1) Always Below 1 Ω
B99-2 (IGF) - B77-51 (IGF1) Always Below 1 Ω
B98-2 (IGF) - B77-51 (IGF1) Always Below 1 Ω
B97-2 (IGF) - B77-51 (IGF1) Always Below 1 Ω
B100-3 (IGT1) - B77-57 (IGT1) Always Below 1 Ω
B99-3 (IGT2) - B77-56 (IGT2) Always Below 1 Ω
B98-3 (IGT3) - B77-55 (IGT3) Always Below 1 Ω
B97-3 (IGT4) - B77-54 (IGT4) Always Below 1 Ω
B100-3 (IGT1) or B77-57 (IGT1) - Body ground Always 10 kΩ or higher
B99-3 (IGT2) or B77-56 (IGT2) - Body ground Always 10 kΩ or higher
B98-3 (IGT3) or B77-55 (IGT3) - Body ground Always 10 kΩ or higher
B97-3 (IGT4) or B77-54 (IGT4) - Body ground Always 10 kΩ or higher
B100-2 (IGF), B99-2 (IGF), B98-2 (IGF), B97-2 (IGF) or B77-51 (IGF1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0351, P0352, P0353 OR P0354)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0351, P0352, P0353 OR P0354)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM(w/ Canister Pump Module)>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Shuffle the arrangement of the ignition coil assemblies (among No. 1 to No. 4 cylinders).

NOTICE:

Do not change the location of the connectors.



f.

Perform a simulation test.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


h.

Read the DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234
Result:
Result Proceed to
Same DTC output A
Different ignition coil DTC output B


HINT:

Perform "Inspection After Repair" after replacing the ignition coil assembly.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION




A

B

5.CHECK HARNESS AND CONNECTOR (IG2 RELAY - IGNITION COIL ASSEMBLY)
a.

Disconnect the ignition coil assembly connectors.


b.

Remove the IG2 relay from the engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B100-1 (+B) - IG2 relay terminal 5 Always Below 1 Ω
B99-1 (+B) - IG2 relay terminal 5 Always Below 1 Ω
B98-1 (+B) - IG2 relay terminal 5 Always Below 1 Ω
B97-1 (+B) - IG2 relay terminal 5 Always Below 1 Ω
B100-1 (+B), B99-1 (+B), B98-1 (+B), B97-1 (+B) or IG2 relay terminal 5 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR