Home › Engine / Hybrid System › 2AR-FE ENGINE CONTROL › SFI SYSTEM(w/ Canister Pump Module) › from 2015.10
RM3090E _51 Engine / Hybrid System _008378 2AR-FE ENGINE CONTROL _0060196 SFI SYSTEM(w/ Canister Pump Module) J

2AR-FE ENGINE CONTROL  SFI SYSTEM(w/ Canister Pump Module)  Fuel Pump Control Circuit  


DESCRIPTION

w/ Fuel Pump Control ECU Assembly:

The fuel pump circuit consists of the ECM, fuel pump and fuel pump control ECU assembly (which operates the fuel pump). Based on the engine output, the ECM determines the fuel pump speed. The speed is then converted to a duty signal and sent to the fuel pump control ECU assembly. Based on the signal sent from the ECM, the fuel pump ECU adjust the fuel pump operation speed.


w/o Fuel Pump Control ECU Assembly:

When the engine is cranked, the ST (starter) relay drive signal output from the engine switch assembly*1 or certification ECU (smart key ECU assembly)*2 is input into the STA terminal of the ECM, and the NE signal generated by the crankshaft position sensor is also input into the NE+ terminal. The ECM interprets that the engine is cranked, and turns transistor Tr1 in the ECM internal circuit on. Current flows to the C/OPN (Circuit Opening) relay by turning Tr1 on. Then, the fuel pump operates.

While the NE signal is input into the ECM with the engine running, the ECM turns Tr1 on continuously.

*1: w/o Entry and Start System

*2: w/ Entry and Start System


WIRING DIAGRAM

A375536E01
0.073,0.042 1.219,0.344 1.146,0.302 12 false for 4WD/AWD: 0.667,3.26 1.802,3.49 1.135,0.229 10 false EFI-MAIN NO. 1 0.958,0.531 1.417,0.729 0.458,0.198 10 false IG2 0.583,6.177 1.417,6.375 0.833,0.198 10 false FL MAIN 3.021,5.115 4.156,5.344 1.135,0.229 10 false EFI-MAIN NO. 2 0.698,7.927 1.531,8.125 0.833,0.198 10 false Battery 2.427,7.615 3.26,7.813 0.833,0.198 10 false V1 2.427,7.792 3.26,7.99 0.833,0.198 10 false Fuel Pump 1.917,7.281 2.135,7.49 0.219,0.208 10 false 4 1.927,8.281 2.76,8.479 0.833,0.198 10 false 5 1.906,7.521 2.74,7.719 0.833,0.198 10 false B 1.906,8.052 2.135,8.24 0.229,0.188 10 false E 3.24,6.635 4.073,6.833 0.833,0.198 10 false C/OPN 0.615,4.969 1.75,5.198 1.135,0.229 10 false EFI-MAIN NO. 2 2.969,3.802 4.104,4.031 1.135,0.229 10 false EFI-MAIN NO. 1 5.427,5.333 6.26,5.531 0.833,0.198 10 false IGN 5.948,3.469 6.781,3.667 0.833,0.198 10 false MREL 5.927,6.802 6.76,7 0.833,0.198 10 false FC 5.667,7.073 5.948,7.281 0.281,0.208 10 false 21 3.823,3.208 4.042,3.417 0.219,0.208 10 false 3 3.833,3.583 4.052,3.792 0.219,0.208 10 false 1 3.052,3.219 3.271,3.427 0.219,0.208 10 false 5 3.052,3.594 3.271,3.802 0.219,0.208 10 false 2 6.448,6.208 6.781,6.417 0.333,0.208 10 false Tr1 6.271,7.719 6.552,7.927 0.281,0.208 10 false A62 6.271,7.927 6.677,8.167 0.406,0.24 10 false ECM 4.667,3.969 5.448,4.188 0.781,0.219 10 false EFI NO. 2 5.677,3.604 5.958,3.813 0.281,0.208 10 false 46 3.344,1.052 3.802,1.25 0.458,0.198 10 false IG2 4.417,1.135 4.875,1.333 0.458,0.198 10 false IG2 4.552,0.896 5.01,1.094 0.458,0.198 10 false 9 3.823,1.854 4.281,2.052 0.458,0.198 10 false G82 3.833,2.052 5.302,2.594 1.469,0.542 10 false Certification ECU (Smart Key ECU Assembly) 3.823,0.844 4.042,1.052 0.219,0.208 10 false 1 3.052,0.844 3.271,1.052 0.219,0.208 10 false 2 3.823,0.5 4.042,0.708 0.219,0.208 10 false 5 3.052,0.49 3.271,0.698 0.219,0.208 10 false 3 3.823,4.531 4.042,4.74 0.219,0.208 10 false 1 3.063,4.51 3.281,4.719 0.219,0.208 10 false 2 3.833,4.917 4.052,5.125 0.219,0.208 10 false 3 3.063,4.896 3.281,5.104 0.219,0.208 10 false 5 3.823,6.417 4.042,6.625 0.219,0.208 10 false 1 3.073,6.417 3.292,6.625 0.219,0.208 10 false 2 3.083,5.979 3.302,6.188 0.219,0.208 10 false 3 3.844,5.979 4.063,6.188 0.219,0.208 10 false 5

A299784E01
6.083,0.563 6.583,0.729 0.5,0.167 10 false MREL 6.083,1.479 6.417,1.646 0.333,0.167 10 false FPC 5.833,1.479 6.083,1.646 0.25,0.167 10 false 21 5.833,0.458 6.083,0.625 0.25,0.167 10 false 46 5.083,1.479 5.25,1.646 0.167,0.167 10 false 2 4.667,1.583 5,1.75 0.333,0.167 10 false FPC 5.083,2.083 5.667,2.25 0.583,0.167 10 false N19 5.083,2.25 5.917,2.583 0.833,0.333 10 false Fuel Pump Control ECU 4.667,2.99 5,3.156 0.333,0.167 10 false FP- 4.042,2.99 4.292,3.156 0.25,0.167 10 false FP 4,1.583 4.167,1.75 0.167,0.167 10 false E 4,1.031 4.25,1.198 0.25,0.167 10 false +B 3.75,0.938 3.917,1.104 0.167,0.167 10 false 1 3.75,1.479 3.917,1.646 0.167,0.167 10 false 4 4,3.167 4.167,3.333 0.167,0.167 10 false 6 4.667,3.167 4.833,3.333 0.167,0.167 10 false 5 4.833,4.042 5,4.208 0.167,0.167 10 false 5 4.167,4.042 4.333,4.208 0.167,0.167 10 false 4 4,4.25 4.167,4.417 0.167,0.167 10 false B 4.646,4.25 4.813,4.417 0.167,0.167 10 false E 4.083,4.833 4.333,5 0.25,0.167 10 false V1 4.083,5 4.833,5.167 0.75,0.167 10 false Fuel Pump 0.917,1.167 1.583,1.333 0.667,0.167 10 false EFI NO. 2 1.083,1.885 1.5,2.385 0.417,0.5 10 false EFI-MAIN NO. 1 2.333,1.885 2.75,2.385 0.417,0.5 10 false EFI-MAIN NO. 2 0.833,4.667 1.333,4.917 0.5,0.25 10 false Battery 2.167,1.667 2.333,1.833 0.167,0.167 10 false 3 6.333,3.583 6.667,3.75 0.333,0.167 10 false A62 6.333,3.75 6.75,3.917 0.417,0.167 10 false ECM 0.667,2.792 1.75,2.958 1.083,0.167 10 false EFI-MAIN NO. 1 2.198,2.792 3.281,2.958 1.083,0.167 10 false EFI-MAIN NO. 2 1.667,1.667 1.833,1.833 0.167,0.167 10 false 1 0.917,1.667 1.083,1.833 0.167,0.167 10 false 1 0.417,1.667 0.583,1.833 0.167,0.167 10 false 3 1.667,2.438 1.833,2.604 0.167,0.167 10 false 2 2.167,2.438 2.333,2.604 0.167,0.167 10 false 5 0.917,2.438 1.083,2.604 0.167,0.167 10 false 2 0.417,2.438 0.583,2.604 0.167,0.167 10 false 5 0.677,3.729 1.26,3.896 0.583,0.167 10 false FL MAIN 6.667,1.583 6.917,1.75 0.25,0.167 10 false Tr1 0.094,0.083 0.802,0.333 0.708,0.25 12 false for 2WD:

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP / SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

·

w/ Fuel Pump Control ECU Assembly


Powertrain > Engine and ECT > Active Test
Tester Display
Control the Fuel Pump / Speed
50004 234 230
·

w/o Fuel Pump Control ECU Assembly


Powertrain > Engine and ECT > Active Test
Tester Display
Control the Fuel Pump / Speed
50004 234 5

e.

Check whether the fuel pump operating sound occurs when performing the Active Test on the GTS.

OK:

Operating sounds can be heard from the fuel pump.


Result:
Result Proceed to
OK
(w/ fuel pump control ECU assembly)
A
OK
(w/o fuel pump control ECU assembly)
B
NG
(w/ fuel pump control ECU assembly)
C
NG
(w/o fuel pump control ECU assembly)
D




A

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP DUTY)

B

6.READ VALUE USING GTS (STARTER SIGNAL)

C

8.CHECK TERMINAL VOLTAGE (POWER SOURCE OF FUEL PUMP CONTROL ECU ASSEMBLY)

D

15.CHECK TERMINAL VOLTAGE (POWER SOURCE OF C/OPN RELAY)
2.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP DUTY)
a.

Remove the fuel suction with pump and gauge tube assembly.


b.

Clean the fuel suction with pump and gauge tube assembly to completely remove any remaining fuel.


c.

Remove the fuel pump.


d.

Connect the fuel pump and fuel suction with pump and gauge tube assembly connector.

NOTICE:

Confirm that no fuel remains inside or on the outside of the fuel pump.



e.

Connect the GTS to the DLC3.


f.

Turn the engine switch on (IG).


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump Duty.

Powertrain > Engine and ECT > Active Test
Tester Display
Control the Fuel Pump Duty
50004 234 229

i.
A285444C02
1.031,1.719 1.552,0.833 false 2.469,1.75 1.865,0.833 false 0.281,0.219 0.646,0.573 0.365,0.354 10 *a 0.958,1.771 1.323,2.125 0.365,0.354 10 1 2.479,1.771 2.844,2.125 0.365,0.354 10 2
*a Component with harness connected
(Fuel Pump)


Operate the fuel pump using the Active Test function and measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection GTS Operation Specified Condition
1 - 2 Fuel pump control duty: 25% 3.4 to 4.1 V
Fuel pump control duty: 80% 10.0 to 12.5 V



j.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

Powertrain > Engine and ECT > Active Test
Tester Display
Control the Fuel Pump / Speed
50004 234 230

k.

Operate the fuel pump using the Active Test function and measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection GTS Operation Specified Condition
1 - 2 ON (Fuel pump control duty: 90%) 10.2 to 14.0 V


HINT:
·

Be sure to measure the voltage with all the connectors connected.

·

Before performing this inspection, check that the battery voltage is between 11 and 14 V (not depleted).




Result:
Proceed to
OK
NG



OK

3.INSPECT FUEL PUMP

NG

9.INSPECT FUEL PUMP
3.INSPECT FUEL PUMP

Result:
Proceed to
OK
NG



OK

END

NG

4.REPLACE FUEL PUMP
4.REPLACE FUEL PUMP
a.

Replace the fuel pump.

Click hereEngine / Hybrid System>2AR-FE FUEL>FUEL PUMP(w/ Canister Pump Module)>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the fuel pump.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION



Result:
Proceed to
NEXT



NEXT

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Check the fuel pump operation.

OK:

Malfunction has been repaired successfully.



Result:
Proceed to
OK
NG



OK

END

NG

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

6.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Starter Signal.

Powertrain > Engine and ECT > Data List
Tester Display
Starter Signal
50003 234 118

e.

Check the result when the engine switch on (IG) and the engine starts.

OK:
Condition Starter Signal
Engine switch on (IG) OFF
Engine Started ON



Result:
Proceed to
OK
NG



OK

7.READ VALUE USING GTS (ENGINE SPEED)

NG

7.READ VALUE USING GTS (ENGINE SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Engine Speed.

Powertrain > Engine and ECT > Data List
Tester Display
Engine Speed
50003 234 9

e.

Read the values displayed on the GTS while cranking.

OK:

Values are displayed continuously.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

8.CHECK TERMINAL VOLTAGE (POWER SOURCE OF FUEL PUMP CONTROL ECU ASSEMBLY)
a.
A290250C21
0.458,1.115 0.813,1.333 0.354,0.219 1.063,1.823 1.25,1.521 true 1.854,1.542 1.99,1.802 true 0.104,0.094 0.417,0.25 0.313,0.156 10 false *a 0.521,1.146 0.979,1.344 0.458,0.198 10 false N19 0.854,1.76 1.167,1.958 0.313,0.198 10 false +B 1.99,1.833 2.146,2.031 0.156,0.198 10 false E
*a Front view of wire harness connector
(to Fuel Pump Control ECU Assembly)


Disconnect the fuel pump control ECU Assembly connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
N19-1 (+B) - N19-4 (E) Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

9.INSPECT FUEL PUMP

NG

13.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU ASSEMBLY - BODY GROUND)
9.INSPECT FUEL PUMP

Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (FUEL PUMP - FUEL PUMP CONTROL ECU ASSEMBLY)

NG

10.CHECK HARNESS AND CONNECTOR (FUEL PUMP - FUEL PUMP CONTROL ECU ASSEMBLY)
a.

Disconnect the fuel pump control ECU assembly connector.


b.

Disconnect the fuel pump connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V1-4 (B) - N19-6 (FP) Always Below 1 Ω
V1-5 (E) - N19-5 (FP-) Always Below 1 Ω
V1-4 (B) or N19-6 (FP) - Body ground Always 10 kΩ or higher
V1-5 (E) or N19-5 (FP-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU ASSEMBLY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU ASSEMBLY - ECM)
a.

Disconnect the fuel pump control ECU assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N19-2 (FPC) - A62-21 (FPC) Always Below 1 Ω
N19-2 (FPC) or A62-21 (FPC) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

12.INSPECT ECM (FPC TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.INSPECT ECM (FPC TERMINAL)
a.

Disconnect the fuel pump control ECU assembly connector.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

Powertrain > Engine and ECT > Active Test
Tester Display
Control the Fuel Pump / Speed
50004 234 5

e.

Operate the fuel pump control ECU assembly using the Active Test function and measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection GTS Operation Specified Condition
N19-2 (FPC) - Body ground Before Active Test → During Active Test Before Active Test: Resistance is stable → During Active Test: Resistance fluctuates*


HINT:

*: Using the Active Test, duty control of the transistors in the ECM will be performed. Due to the duty control, resistance of the FPC terminal will be unstable during the Active Test. If the resistance is stable before the Active Test and fluctuates while performing the Active Test, it can be determined that the transistor is operating. If the transistor does not operate during the Active Test, the ECM may be malfunctioning.



Result:
Proceed to
OK
NG



OK

REPLACE FUEL PUMP CONTROL ECU ASSEMBLY

NG

13.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU ASSEMBLY - BODY GROUND)
a.

Disconnect the fuel pump control ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N19-4 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

14.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 2 RELAY - FUEL PUMP CONTROL ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 2 RELAY - FUEL PUMP CONTROL ECU ASSEMBLY)
a.

Remove the EFI-MAIN NO. 2 relay from the engine room relay block and junction block assembly.


b.

Disconnect the fuel pump control ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (EFI-MAIN NO. 2 relay) - N19-1 (+B) Always Below 1 Ω
3 (EFI-MAIN NO. 2 relay) or N19-1 (+B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.CHECK TERMINAL VOLTAGE (POWER SOURCE OF C/OPN RELAY)
a.
A298899C04
0.063,0.063 0.375,0.219 0.313,0.156 10 *1 2.042,1.115 2.354,1.271 0.313,0.156 10 *2
*1 Engine Room Relay Block and Junction Block Assembly
*2 C/OPN Relay


Remove the C/OPN relay from the engine room relay block and junction block assembly.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
1 (C/OPN relay) - Body ground Engine switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

16.INSPECT C/OPN RELAY

NG

22.CHECK HARNESS AND CONNECTOR (C/OPN RELAY - IG2 RELAY)
16.INSPECT C/OPN RELAY

Result:
Proceed to
OK
NG



OK

17.CHECK HARNESS AND CONNECTOR (C/OPN RELAY - ECM)

NG

REPLACE C/OPN RELAY

17.CHECK HARNESS AND CONNECTOR (C/OPN RELAY - ECM)
a.

Remove the C/OPN relay from the engine room relay block and junction block assembly.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (C/OPN relay) - A62-21 (FC) Always Below 1 Ω
2 (C/OPN relay) or A62-21 (FC) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

18.CHECK HARNESS AND CONNECTOR (C/OPN RELAY - FUEL PUMP)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.CHECK HARNESS AND CONNECTOR (C/OPN RELAY - FUEL PUMP)
a.

Remove the C/OPN relay from the engine room relay block and junction block assembly.


b.

Disconnect the fuel pump connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (C/OPN relay) - V1-4 (B) Always Below 1 Ω
3 (C/OPN relay) or V1-4 (B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

19.CHECK HARNESS AND CONNECTOR (FUEL PUMP - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

19.CHECK HARNESS AND CONNECTOR (FUEL PUMP - BODY GROUND)
a.

Disconnect the fuel pump connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V1-5 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

20.INSPECT FUEL PUMP

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

20.INSPECT FUEL PUMP

Result:
Proceed to
OK
NG



OK

21.CHECK HARNESS AND CONNECTOR (C/OPN RELAY - EFI-MAIN NO. 2 RELAY)

NG

21.CHECK HARNESS AND CONNECTOR (C/OPN RELAY - EFI-MAIN NO. 2 RELAY)
a.

Remove the C/OPN relay and EFI-MAIN NO. 2 relay from the engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 (C/OPN relay) - 3 (EFI-MAIN NO. 2 relay) Always Below 1 Ω
5 (C/OPN relay) or 3 (EFI-MAIN NO. 2 relay) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

22.CHECK HARNESS AND CONNECTOR (C/OPN RELAY - IG2 RELAY)
a.

Remove the C/OPN relay and IG2 relay from the engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (C/OPN relay) - 5 (IG2 relay) Always Below 1 Ω
1 (C/OPN relay) or 5 (IG2 relay) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR