Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU) › from 2015.10
RM3090E _57 Power Source / Network _008434 NETWORKING _0221950 CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU) C

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU)  U0208  Lost Communication with "Seat Control Module A"  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
U0208 Lost Communication with "Seat Control Module A" There is no communication from the position control ECU and switch assembly.
·

Power source or inside position control ECU and switch assembly

·

Position control ECU and switch assembly CAN branch wire or connector

·

Position control ECU and switch assembly


Main body ECU (multiplex network body ECU)

WIRING DIAGRAM

C251476E13
1.656,0.688 1.927,0.927 0.271,0.24 10 false 3 1.667,1.094 1.927,1.271 0.26,0.177 10 false 9 0.406,1.583 0.938,1.813 0.531,0.229 10 false N30 0.396,1.75 2.458,2.042 2.063,0.292 10 false No. 4 CAN Junction Connector 1.708,2.396 2.583,2.573 0.875,0.177 10 false from Battery 3.531,2.76 4.479,3.073 0.948,0.313 10 false ECU-B NO.1 3.552,2.229 4.49,2.615 0.938,0.385 10 false P/SEAT F/L 1.719,2.906 2.698,3.188 0.979,0.281 10 false from Battery 5.24,4.135 6.802,4.542 1.563,0.406 10 false Position Control ECU and Switch Assembly 5.292,0.583 5.688,0.844 0.396,0.26 10 false 8 5.292,1.01 5.646,1.26 0.354,0.25 10 false 7 5.26,2.906 5.583,3.083 0.323,0.177 10 false e6 5.292,2.177 5.604,2.344 0.313,0.167 10 false 7 5.229,2.396 5.542,2.563 0.313,0.167 10 false e18 5.24,2.688 5.583,2.854 0.344,0.167 10 false 12 5.229,3.375 5.615,3.615 0.385,0.24 10 false e18 5.292,3.167 5.542,3.375 0.25,0.208 10 false 2 5.271,1.219 5.594,1.396 0.323,0.177 10 false e6 5.271,0.792 5.594,0.969 0.323,0.177 10 false e6 5.635,3.365 6.146,3.604 0.51,0.24 10 false GND1 5.635,2.917 6.146,3.156 0.51,0.24 10 false SYSB 5.635,2.396 6.146,2.635 0.51,0.24 10 false +B1 5.625,1.229 6.135,1.469 0.51,0.24 10 false CANN 5.604,0.771 6.115,1.01 0.51,0.24 10 false CANP

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the ignition switch to ON and wait at least 20 seconds.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU)>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 123
HINT:

If DTC U1002 is output from gateway of the main body ECU (multiplex network body ECU), this indicates a sub bus 1 malfunction. Troubleshoot for DTC U1002 and check for malfunctions in sub bus 1.



Result:
Result Proceed to
DTC U1002 is not output from main body ECU (multiplex network body ECU) A
DTC U1002 is output from main body ECU (multiplex network body ECU) B



A

2.CHECK FOR OPEN IN CAN BUS WIRE (POSITION CONTROL ECU AND SWITCH ASSEMBLY CAN BRANCH WIRE)

B

GO TO GO TO DIAGNOSIS PROCEDURE INDICATED BY OUTPUT DTC

2.CHECK FOR OPEN IN CAN BUS WIRE (POSITION CONTROL ECU AND SWITCH ASSEMBLY CAN BRANCH WIRE)
a.
C219233C02
1.302,1.417 1.698,1.688 0.396,0.271 2.594,1.76 2.458,1.76 2.458,1.76 2.302,1.573 true 2.521,1.969 2.385,1.969 2.385,1.969 2.219,1.573 true 0.083,0.063 0.396,0.302 0.313,0.24 10 false *a 1.406,1.438 1.771,1.667 0.365,0.229 10 false e6 2.635,1.646 3.177,1.917 0.542,0.271 10 false CANN 2.573,1.875 3.115,2.146 0.542,0.271 10 false CANP
*a Rear view of wire harness connector
(to Position Control ECU and Switch Assembly)


Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the position control ECU and switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
e6-8 (CANP) - e6-7 (CANN) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY CAN BRANCH WIRE OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - BATTERY AND BODY GROUND)
a.
C219234C04
0.208,1.208 0.625,1.479 0.417,0.271 2.781,1.385 3.177,1.646 0.396,0.26 0.792,1.813 0.99,1.813 0.99,1.813 1.385,1.385 true 0.781,0.781 0.979,0.781 0.979,0.781 1.385,1.24 true 1.781,1.896 1.938,1.896 1.938,1.896 2.083,1.583 true 0.104,0.073 0.594,0.49 0.49,0.417 10 false *a 0.302,1.271 0.677,1.521 0.375,0.25 10 false e18 2.885,1.438 3.219,1.656 0.333,0.219 10 false e6 0.375,0.688 0.802,0.938 0.427,0.25 10 false GND1 0.479,1.719 0.906,1.969 0.427,0.25 10 false +B1 1.354,1.792 1.844,2.042 0.49,0.25 10 false SYSB
*a Rear view of wire harness connector
(to Position Control ECU and Switch Assembly)


Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



b.

Disconnect the position control ECU and switch assembly connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
e6-12 (SYSB) - Body ground Always 11 to 14 V
e18-7 (+B1) - Body ground Always 11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
e18-2 (GND1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR