Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU) › 2015.10–2016.08
RM3090E _57 Power Source / Network _008434 NETWORKING _0221950 CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU)  Check Bus 2 Line for Short to GND  


DESCRIPTION

There may be a short circuit between one of the CAN bus wires and GND when no resistance exists between terminal 18 (CA4H) of the central gateway ECU and terminal 4 (CG) of the DLC3, or terminal 17 (CA4L) of the central gateway ECU and terminal 4 (CG) of the DLC3.

Detection Item Trouble Area

*1: w/ Entry and Start System

*2: for 4WD/AWD

*3: w/ Stop and Start System

No resistance exists between terminal 18 (CA4H) of the central gateway ECU and terminal 4 (CG) of the DLC3, or terminal 17 (CA4L) of the central gateway ECU and terminal 4 (CG) of the DLC3.
·

Short to GND in bus 2 CAN main wires

·

Short to GND in bus 2 CAN branch wires

·

ECM

·

Combination meter assembly

·

Central gateway ECU

·

Power steering ECU assembly

·

Air conditioning amplifier assembly

·

Airbag sensor assembly

·

Spiral with sensor cable sub-assembly (steering angle sensor)

·

Certification ECU (smart key ECU assembly)*1

·

4WD ECU assembly*2

·

Brake actuator assembly (skid control ECU)

·

Main body ECU (multiplex network body ECU)

·

Engine stop and start ECU*3

·

No. 6 CAN junction connector

·

No. 7 CAN junction connector



WIRING DIAGRAM

C347347E02
0.292,1.635 1.969,2.073 1.677,0.438 10 false G78 0.292,1.771 1.969,2.208 1.677,0.438 10 false Main Body ECU (Multiplex Network Body ECU) 0.865,0.667 2.542,1.104 1.677,0.438 10 false CANH 0.885,1.177 1.896,1.448 1.01,0.271 10 false CANL 1.375,1.094 2.385,1.365 1.01,0.271 10 false 13 1.375,0.552 2.385,0.823 1.01,0.271 10 false 14 3.177,1.094 4.188,1.365 1.01,0.271 10 false 11 3.25,0.552 4.26,0.823 1.01,0.271 10 false 1 4.052,1.083 5.063,1.354 1.01,0.271 10 false 15 4.052,0.521 5.063,0.792 1.01,0.271 10 false 5 4.063,2.49 5.073,2.76 1.01,0.271 10 false 2 4.063,3.021 5.073,3.292 1.01,0.271 10 false 12 3.177,3.031 4.188,3.302 1.01,0.271 10 false 13 3.26,2.49 4.271,2.76 1.01,0.271 10 false 3 5.99,2.594 6.698,3.052 0.708,0.458 10 false CANH 5.99,3.125 6.698,3.583 0.708,0.458 10 false CANL 5.75,2.5 6.76,2.771 1.01,0.271 10 false 4 5.75,3.021 6.76,3.292 1.01,0.271 10 false 8 5.146,3.531 6.75,3.969 1.604,0.438 10 false h1 5.167,3.688 7.125,4.125 1.958,0.438 10 false Power Steering ECU Assembly 0.875,2.635 1.583,3.094 0.708,0.458 10 false CANH 0.927,3.146 1.635,3.604 0.708,0.458 10 false CANL 1.417,3.021 2.427,3.292 1.01,0.271 10 false 10 1.427,2.51 2.438,2.781 1.01,0.271 10 false 22 0.24,3.531 1.917,3.969 1.677,0.438 10 false A80 0.25,3.677 1.927,4.115 1.677,0.438 10 false Brake Actuator Assembly (Skid Control ECU) 4.063,6.406 5.073,6.677 1.01,0.271 10 false 4 4.063,6.938 5.073,7.208 1.01,0.271 10 false 14 4.063,4.99 5.073,5.26 1.01,0.271 10 false 19 4.063,4.448 5.073,4.719 1.01,0.271 10 false 9 3.167,4.979 4.177,5.25 1.01,0.271 10 false 20 3.135,4.458 4.146,4.729 1.01,0.271 10 false 10 0.875,4.573 1.583,5.031 0.708,0.458 10 false CANH 5.99,4.531 6.698,4.99 0.708,0.458 10 false CANH 6,5.094 6.708,5.552 0.708,0.458 10 false CANL 0.917,5.104 1.625,5.563 0.708,0.458 10 false CANL 5.667,4.448 6.677,4.719 1.01,0.271 10 false 13 5.667,4.99 6.677,5.26 1.01,0.271 10 false 22 1.448,4.979 2.458,5.25 1.01,0.271 10 false 12 1.427,4.438 2.438,4.708 1.01,0.271 10 false 11 0.104,5.365 0.813,5.875 0.708,0.51 10 false G81 0.115,5.521 2.458,5.833 2.344,0.313 10 false Air Conditioning Amplifier Assembly 5.469,5.417 6.521,5.625 1.052,0.208 10 false G92 5.479,5.573 7.156,6.01 1.677,0.438 10 false Airbag Sensor Assembly 0.302,7.208 2.615,7.417 2.313,0.208 10 false *1: for 2AR-FE, 3ZR-FAE, 3ZR-FE 0.302,7.552 2.615,7.76 2.313,0.208 10 false *2: for 2WW 0.281,7.885 3.281,8.073 3,0.188 10 false *3: for 2AD-FTV, 2AD-FHV, 2AD-CCo, 2AD-DPF 5.958,0.563 6.667,1.021 0.708,0.458 10 false CANH 5.969,1.313 6.677,1.771 0.708,0.458 10 false CANL 6.198,1.625 6.906,2.083 0.708,0.458 10 false ECM 4.49,0.635 5.01,0.938 0.521,0.302 10 false A62 5,0.625 5.521,0.927 0.521,0.302 10 false A62 4.5,1.167 5.021,1.469 0.521,0.302 10 false A62 4.979,1.167 5.5,1.469 0.521,0.302 10 false A62 5.51,1.167 6.031,1.469 0.521,0.302 10 false A61 5.521,0.635 6.042,0.938 0.521,0.302 10 false A61 4.469,0.427 5.479,0.698 1.01,0.271 10 false 13*1 4.979,0.417 5.99,0.688 1.01,0.271 10 false 26*2 5.552,0.427 6.563,0.698 1.01,0.271 10 false 7*3 4.49,0.938 5.5,1.208 1.01,0.271 10 false 26*1 5,0.948 6.01,1.219 1.01,0.271 10 false 25*2 5.542,0.958 6.552,1.229 1.01,0.271 10 false 6*3 2.771,7.385 5.771,7.573 3,0.188 10 false G171 2.771,7.531 5.771,7.719 3,0.188 10 false No. 6 CAN Junction Connector

C347348E02
2.771,7.563 7.052,7.76 4.281,0.198 10 false G172 2.771,7.729 7.052,7.927 4.281,0.198 10 false No. 7 CAN Junction Connector 4.063,0.74 4.74,1.031 0.677,0.292 10 false 8 4.052,1.26 4.729,1.552 0.677,0.292 10 false 18 4.083,6.51 4.76,6.802 0.677,0.292 10 false 1 4.063,7.052 4.74,7.344 0.677,0.292 10 false 11 5.979,7.281 6.656,7.573 0.677,0.292 10 false CANL 5.979,6.521 6.656,6.813 0.677,0.292 10 false CANH 5.698,7.073 6.375,7.365 0.677,0.292 10 false 31 5.698,6.542 6.375,6.833 0.677,0.292 10 false 32 5.229,7.552 7.146,7.917 1.917,0.365 10 false G16 5.219,7.698 7.135,8.063 1.917,0.365 10 false Combination Meter Assembly 4.073,4.615 4.75,4.906 0.677,0.292 10 false 7 4.094,5.115 4.771,5.406 0.677,0.292 10 false 17 3.229,4.615 3.906,4.906 0.677,0.292 10 false 9 3.167,5.156 3.844,5.448 0.677,0.292 10 false 19 3.229,0.74 3.906,1.031 0.677,0.292 10 false 4 3.156,1.292 3.833,1.583 0.677,0.292 10 false 14 0.875,0.844 1.552,1.135 0.677,0.292 10 false CANH 0.896,1.354 1.573,1.646 0.677,0.292 10 false CANL 1.396,1.271 2.073,1.563 0.677,0.292 10 false 14 1.396,0.76 2.073,1.052 0.677,0.292 10 false 13 0.313,1.771 1.635,2.125 1.323,0.354 10 false G87 0.302,1.906 2.469,2.198 2.167,0.292 10 false Engine Stop and Start ECU*3 4.094,2.656 4.771,2.948 0.677,0.292 10 false 5 4.094,3.198 4.771,3.49 0.677,0.292 10 false 15 3.25,2.667 3.927,2.958 0.677,0.292 10 false 6 3.177,3.198 3.854,3.49 0.677,0.292 10 false 16 0.083,5.51 2.573,5.844 2.49,0.333 10 false G12 0.073,5.667 2.552,6.052 2.479,0.385 10 false Spiral with Sensor Cable Sub-assembly (Steering Angle Sensor) 0.875,2.76 1.552,3.052 0.677,0.292 10 false CANH 5.979,2.771 6.656,3.063 0.677,0.292 10 false CANH 0.865,4.719 1.542,5.01 0.677,0.292 10 false CANH 0.885,3.313 1.563,3.604 0.677,0.292 10 false CANL 6,3.281 6.677,3.573 0.677,0.292 10 false CANL 0.917,5.24 1.594,5.531 0.677,0.292 10 false CANL 5.99,5.24 6.667,5.531 0.677,0.292 10 false CA4L 6,4.708 6.677,5 0.677,0.292 10 false CA4H 1.406,2.667 2.083,2.958 0.677,0.292 10 false 6 1.417,3.208 2.094,3.5 0.677,0.292 10 false 5 5.698,3.208 6.375,3.5 0.677,0.292 10 false 15 5.708,2.677 6.385,2.969 0.677,0.292 10 false 14 5.49,3.698 7.135,4.042 1.646,0.344 10 false G84 5.479,3.854 7.01,4.208 1.531,0.354 10 false Certification ECU (Smart Key ECU Assembly)*1 1.448,4.563 2.125,4.854 0.677,0.292 10 false 3 1.427,5.104 2.104,5.396 0.677,0.292 10 false 2 0.146,3.573 1.677,3.927 1.531,0.354 10 false G86 0.135,3.771 1.667,4.125 1.531,0.354 10 false 4WD ECU Assembly*2 5.615,5.094 6.292,5.385 0.677,0.292 10 false 17 5.615,4.583 6.292,4.875 0.677,0.292 10 false 18 5.531,5.531 6.063,5.792 0.531,0.26 10 false G170 5.552,5.698 7.094,5.917 1.542,0.219 10 false Central Gateway ECU 0.177,7.219 2.656,7.604 2.479,0.385 10 false *1: w/ Entry and Start System 0.177,7.667 2.656,8.052 2.479,0.385 10 false *2: for 4WD/AWD 0.188,8.125 2.667,8.51 2.479,0.385 10 false *3: w/ Stop and Start System

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU)>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 6 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) battery terminal.

C280369C28
3.125,1.385 3.646,1.698 0.521,0.313 5.302,0.781 5.719,1.052 0.417,0.271 1.01,1.458 0.917,1.344 0.917,1.344 0.781,1.344 true 1.229,1.469 0.969,1.125 0.969,1.125 0.833,1.125 true 1.594,1.448 1.104,0.615 1.104,0.615 0.969,0.615 true 1.75,1.479 1.323,0.406 1.323,0.406 1.188,0.406 true 1.031,1.625 0.958,1.729 0.958,1.729 0.823,1.729 true 1.25,1.604 1.063,1.927 1.063,1.927 0.927,1.927 true 1.604,1.646 1.271,2.375 1.271,2.375 1.083,2.375 true 1.792,1.635 1.438,2.594 1.438,2.594 1.177,2.594 true 3.26,2.667 3.083,2.667 3.083,2.667 2.719,1.615 true 3.365,0.344 3.146,0.344 3.146,0.344 2.729,1.448 true 1.396,1.635 1.115,2.177 1.115,2.177 0.979,2.177 true 1.406,1.479 1.01,0.844 1.01,0.844 0.875,0.844 true 3.531,0.635 3.313,0.635 3.313,0.635 2.917,1.448 true 3.469,2.313 3.292,2.313 3.292,2.313 2.885,1.625 true 5.438,1.302 4.896,0.958 4.896,0.958 4.76,0.958 true 0.104,0.167 0.75,0.323 0.646,0.156 10 false *a 4.271,0.25 4.583,0.406 0.313,0.156 10 false *b 0.24,1.281 0.813,1.552 0.573,0.271 10 false CANH*c 0.292,1.083 0.875,1.365 0.583,0.281 10 false CANH*d 0.448,0.563 1.031,0.781 0.583,0.219 10 false CANH*f 0.677,0.333 1.26,0.563 0.583,0.229 10 false CANH*g 3.333,2.594 3.896,2.75 0.563,0.156 10 false CANL*h 3.208,1.458 3.615,1.667 0.406,0.208 10 false G171 5.375,0.833 5.708,1.021 0.333,0.188 10 false G14 4.5,0.885 4.813,1.042 0.313,0.156 10 false CG 3.427,0.281 3.99,0.438 0.563,0.156 10 false CANH*h 0.667,2.51 1.354,2.667 0.688,0.156 10 false CANL*g 0.292,1.656 0.938,1.813 0.646,0.156 10 false CANL*c 0.406,1.875 0.99,2.156 0.583,0.281 10 false CANL*d 0.479,2.104 1.063,2.396 0.583,0.292 10 false CANL*e 0.583,2.323 1.167,2.542 0.583,0.219 10 false CANL*f 0.333,0.792 0.917,1.083 0.583,0.292 10 false CANH*e 3.583,0.563 4.146,0.74 0.563,0.177 10 false CANH*i 3.531,2.229 4.115,2.406 0.583,0.177 10 false CANL*i
*a Front view of wire harness connector
(to No. 6 CAN Junction Connector)
*b Front view of DLC3
*c to Main Body ECU (Multiplex Network Body ECU) *d to Power Steering ECU Assembly
*e to Brake Actuator Assembly (Skid Control ECU) *f to No. 7 CAN Junction Connector
*g to ECM *h to Airbag Sensor Assembly
*i to Air Conditioning Amplifier Assembly - -



b.

Disconnect the No. 6 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connect to
G171-1 (CANH) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Main body ECU (multiplex network body ECU)
G171-11 (CANL) - G14-4 (CG)
G171-2 (CANH) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Power steering ECU assembly
G171-12 (CANL) - G14-4 (CG)
G171-3 (CANH) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Brake actuator assembly (skid control ECU)
G171-13 (CANL) - G14-4 (CG)
G171-4 (CANH) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher No. 7 CAN junction connector
G171-14 (CANL) - G14-4 (CG)
G171-5 (CANH) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher ECM
G171-15 (CANL) - G14-4 (CG)
G171-9 (CANH) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Airbag sensor assembly
G171-19 (CANL) - G14-4 (CG)
G171-10 (CANH) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Air conditioning amplifier assembly
G171-20 (CANL) - G14-4 (CG)



Result:
Result Proceed to
OK A
NG (No. 7 CAN junction connector CAN main wire) B
NG (ECU or sensor CAN main or branch wires) C



A

REPLACE NO. 6 CAN JUNCTION CONNECTOR

B

2.CONNECT CONNECTOR

C

6.CHECK FOR SHORT TO GND IN CAN BUS WIRE (ECU, SENSOR)
2.CONNECT CONNECTOR
a.

Reconnect the G171 No. 6 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

3.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 7 CAN JUNCTION CONNECTOR)
3.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 7 CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 7 CAN junction connector.

C280369C29
3.125,1.385 3.646,1.698 0.521,0.313 5.302,0.781 5.719,1.052 0.417,0.271 1.76,1.458 1.271,0.625 1.271,0.625 1.135,0.625 true 1.781,1.646 1.448,2.375 1.448,2.375 1.26,2.375 true 2.698,2.688 2.521,2.688 2.521,2.688 2.156,1.635 true 2.865,0.208 2.646,0.208 2.646,0.208 2.156,1.458 true 3,0.458 2.781,0.458 2.781,0.458 2.344,1.438 true 3.167,2 2.99,2 2.99,2 2.74,1.625 true 3.135,0.708 2.917,0.708 2.917,0.708 2.542,1.448 true 3.26,0.979 3.042,0.979 3.042,0.979 2.74,1.479 true 2.906,2.458 2.729,2.458 2.729,2.458 2.333,1.625 true 3.021,2.219 2.844,2.219 2.844,2.219 2.521,1.635 true 1.042,1.625 0.896,1.917 0.896,1.917 0.708,1.917 true 1.021,1.458 0.823,1.167 0.823,1.167 0.688,1.167 true 1.552,1.448 0.979,0.896 0.979,0.896 0.844,0.896 true 1.573,1.625 1.198,2.167 1.198,2.167 1.01,2.167 true 5.438,1.292 4.896,0.979 4.896,0.979 4.76,0.979 true 0.104,0.167 0.75,0.323 0.646,0.156 10 false *a 4.271,0.25 4.583,0.406 0.313,0.156 10 false *b 0.125,1.073 0.708,1.302 0.583,0.229 10 false CANH*c 0.313,0.802 0.906,1 0.594,0.198 10 false CANH*d 2.906,0.146 3.49,0.365 0.583,0.219 10 false CANH*f 3.073,0.385 3.656,0.615 0.583,0.229 10 false CANH*g 3.063,2.146 3.688,2.354 0.625,0.208 10 false CANL*h 3.208,1.458 3.615,1.667 0.406,0.208 10 false G172 5.375,0.833 5.708,1.021 0.333,0.188 10 false G14 4.479,0.917 4.833,1.146 0.354,0.229 10 false CG 3.188,0.646 3.75,0.802 0.563,0.156 10 false CANH*h 2.948,2.375 3.646,2.573 0.698,0.198 10 false CANL*g 0.167,1.823 0.698,2.063 0.531,0.24 10 false CANL*c 0.75,2.281 1.396,2.448 0.646,0.167 10 false CANL*e 2.74,2.604 3.323,2.792 0.583,0.188 10 false CANL*f 0.583,0.51 1.177,0.75 0.594,0.24 10 false CANH*e 0.438,2.083 1,2.302 0.563,0.219 10 false CANL*d 3.302,0.906 3.865,1.063 0.563,0.156 10 false CANH*i 3.219,1.927 3.844,2.135 0.625,0.208 10 false CANL*i
*a Front view of wire harness connector
(to No. 7 CAN Junction Connector)
*b Front view of DLC3
*c to Combination Meter Assembly *d to Engine Stop and Start ECU (w/ Stop and Start System)
*e to Certification ECU (Smart Key ECU Assembly) (w/ Entry and Start System) *f to 4WD ECU Assembly (for 4WD/AWD)
*g to Central Gateway ECU *h to No. 6 CAN Junction Connector
*i to Spiral with Sensor Cable Sub-assembly (Steering Angle Sensor) - -



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connect to

*1: w/ Entry and Start System

*2: for 4WD/AWD

*3: w/ Stop and Start System

G172-1 (CANH) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Combination meter assembly
G172-11 (CANL) - G14-4 (CG)
G172-4 (CANH) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Engine stop and start ECU*3
G172-14 (CANL) - G14-4 (CG)
G172-5 (CANH) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Certification ECU (smart key ECU assembly)*1
G172-15 (CANL) - G14-4 (CG)
G172-6 (CANH) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher 4WD ECU assembly*2
G172-16 (CANL) - G14-4 (CG)
G172-7 (CANH) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Central gateway ECU
G172-17 (CANL) - G14-4 (CG)
G172-8 (CANH) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher No. 6 CAN junction connector
G172-18 (CANL) - G14-4 (CG)
G172-9 (CANH) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Spiral with sensor cable sub-assembly (steering angle sensor)
G172-19 (CANL) - G14-4 (CG)



Result:
Result Proceed to
OK A
NG (No. 6 CAN junction connector CAN main wire) B
NG (Central gateway ECU CAN branch wire) C
NG (ECU or sensor CAN main or branch wires) D



A

REPLACE NO. 7 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 7 CAN JUNCTION CONNECTOR - NO. 6 CAN JUNCTION CONNECTOR)

C

4.CONNECT CONNECTOR

D

6.CHECK FOR SHORT TO GND IN CAN BUS WIRE (ECU, SENSOR)
4.CONNECT CONNECTOR
a.

Reconnect the G172 No. 7 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

5.CHECK FOR SHORT TO GND IN CAN BUS WIRE (CENTRAL GATEWAY ECU)
5.CHECK FOR SHORT TO GND IN CAN BUS WIRE (CENTRAL GATEWAY ECU)
a.
C338146C23
1.458,2.573 1.979,2.802 0.521,0.229 0.708,0.458 1.219,0.677 0.51,0.219 2.219,4.135 2.031,4.135 2.031,4.135 1.594,3.302 true 2.104,0.5 1.917,0.5 1.917,0.5 1.656,1.438 true 2.458,2.208 2.271,2.208 2.271,2.208 1.792,1.51 true 0.094,0.208 0.406,0.365 0.313,0.156 10 false *a 0.135,2.49 0.448,2.646 0.313,0.156 10 false *b 1.583,2.604 1.938,2.792 0.354,0.188 10 false G14 0.792,0.479 1.302,0.708 0.51,0.229 10 false G170 2.313,4.063 2.844,4.313 0.531,0.25 10 false CG 2.177,0.417 2.635,0.635 0.458,0.219 10 false CA4L 2.531,2.115 2.938,2.333 0.406,0.219 10 false CA4H
*a Front view of wire harness connector
(to Central Gateway ECU)
*b Front view of DLC3


Disconnect the central gateway ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G170-18 (CA4H) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G170-17 (CA4L) - G14-4 (CG)



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (CENTRAL GATEWAY ECU - NO. 7 CAN JUNCTION CONNECTOR)

6.CHECK FOR SHORT TO GND IN CAN BUS WIRE (ECU, SENSOR)
a.
C334464C33
1.469,0.302 1.958,0.552 0.49,0.25 1.49,2.469 1.927,2.719 0.438,0.25 2.25,2.083 2.083,2.083 2.083,2.083 1.667,1.135 true 1.063,2.698 1.24,2.698 1.24,2.698 1.604,3.073 true 2.406,1.823 2.24,1.823 2.24,1.823 1.76,1.125 true 0.146,0.125 0.438,0.417 0.292,0.292 10 false *a 0.135,2.5 0.5,2.75 0.365,0.25 10 false *b 1.583,2.49 1.969,2.792 0.385,0.302 10 false G14 1.552,0.333 2.021,0.646 0.469,0.313 10 false G170 0.792,2.594 1.146,2.823 0.354,0.229 10 false CG 2.458,1.698 2.958,1.948 0.5,0.25 10 false CA4L 2.302,1.969 2.802,2.219 0.5,0.25 10 false CA4H
*a Component with harness connected
(Central Gateway ECU)
*b Front view of DLC3


Reconnect the CAN junction connector.


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the bus line shorted to GND is connected.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G170-18 (CA4H) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G170-17 (CA4L) - G14-4 (CG)


HINT:

If the resistance changes to 200 Ω or higher when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.



Result:
Proceed to
OK
NG



OK

REPLACE CORRESPONDING ECU OR SENSOR

NG

REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR CAN BUS WIRES OR CONNECTOR