Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU) › 2015.10–2016.08
RM3090E _57 Power Source / Network _008434 NETWORKING _0221950 CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU)  Open in Bus 3 Main Bus Line  


DESCRIPTION

There may be an open circuit in one of the bus 3 CAN main wires when the resistance between terminals 6 (CA3H) and 21 (CA3L) of the central gateway ECU is 70 Ω or higher.

Symptom Trouble Area
Resistance between terminals 6 (CA3H) and 21 (CA3L) of central gateway ECU is 70 Ω or higher.
·

CAN main wire or connector

·

Central gateway ECU

·

No. 8 CAN junction connector



This malfunction is not related to the lines of a bus 3 branch or to ECUs or sensors connected to a bus 3 branch.

WIRING DIAGRAM

C334602E03
5.115,3.823 6.688,4.156 1.573,0.333 10 false Central Gateway ECU 5.094,3.625 5.594,3.938 0.5,0.313 10 false G170 0.219,3.698 2.219,3.958 2,0.26 10 false No. 8 CAN Junction Connector 0.219,3.542 0.719,3.865 0.5,0.323 10 false G173 5.677,0.583 6.177,0.771 0.5,0.188 10 false CA3H 5.688,1.281 6.188,1.469 0.5,0.188 10 false CA3L 5.688,2.563 6.188,2.75 0.5,0.188 10 false CAYH 5.698,3.333 6.198,3.521 0.5,0.188 10 false CAYL 5.344,2.552 5.573,2.75 0.229,0.198 10 false 19 5.344,3.021 5.573,3.219 0.229,0.198 10 false 20 5.344,1 5.573,1.198 0.229,0.198 10 false 21 5.406,0.542 5.573,0.74 0.167,0.198 10 false 6 1.802,2.552 1.969,2.75 0.167,0.198 10 false 4 1.771,3.021 2,3.219 0.229,0.198 10 false 15 1.813,0.563 1.979,0.76 0.167,0.198 10 false 3 1.781,1 2.01,1.198 0.229,0.198 10 false 14

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU)>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (NO. 8 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU)
a.

Disconnect the cable from the negative (-) battery terminal.

C311975C68
1.313,1.781 1.823,2.052 0.51,0.271 2.073,3.073 2.375,3.073 2.375,3.073 3.042,2.188 true 2.01,0.917 2.313,0.917 2.313,0.917 3.01,1.927 true 2.146,0.656 2.448,0.656 2.448,0.656 3.198,1.958 true 2.281,3.375 2.583,3.375 2.583,3.375 3.229,2.188 true 1.385,1.833 2,2.188 0.615,0.354 10 false G173 0.219,0.146 0.531,0.344 0.313,0.198 10 false *a 1.573,0.833 2.021,1.073 0.448,0.24 10 false CANH 1.656,3 2.083,3.25 0.427,0.25 10 false CANL 1.729,0.583 2.177,0.823 0.448,0.24 10 false CANH 1.875,3.292 2.302,3.542 0.427,0.25 10 false CANL
*a Front view of wire harness connector
(to No. 8 CAN Junction Connector)
- -



b.

Disconnect the No. 8 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G173-3 (CANH) - G173-14 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω
G173-4 (CANH) - G173-15 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE NO. 8 CAN JUNCTION CONNECTOR

NG

2.CONNECT CONNECTOR
2.CONNECT CONNECTOR
a.

Reconnect the G173 No. 8 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

3.CHECK FOR OPEN IN CAN BUS WIRE (CENTRAL GATEWAY ECU)
3.CHECK FOR OPEN IN CAN BUS WIRE (CENTRAL GATEWAY ECU)
a.
C326490C27
1.5,0.167 2.031,0.385 0.531,0.219 2.771,1.917 2.573,1.917 2.573,1.917 2.188,1.208 true 2.729,0.281 2.542,0.281 2.542,0.281 2.313,0.948 true 1.458,1.813 1.656,1.813 1.656,1.813 1.896,1.198 true 1.625,2.042 1.823,2.042 1.823,2.042 2.052,1.208 true 0.135,0.094 0.438,0.427 0.302,0.333 10 false *a 1.583,0.198 2.188,0.5 0.604,0.302 10 false G170 2.802,0.229 3.229,0.531 0.427,0.302 10 false CA3H 2.823,1.844 3.313,2.083 0.49,0.24 10 false CA3L 1.031,1.729 1.469,1.896 0.438,0.167 10 false CAYH 1.198,1.969 1.635,2.135 0.438,0.167 10 false CAYL
*a Front view of wire harness connector
(to Central Gateway ECU)


Disconnect the central gateway ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G170-6 (CA3H) - G170-21 (CA3L) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G170-19 (CAYH) - G170-20 (CAYL) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (CENTRAL GATEWAY ECU - NO. 8 CAN JUNCTION CONNECTOR)