Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU) › from 2015.10
RM3090E _57 Power Source / Network _008434 NETWORKING _0221950 CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU)  Check Bus 5 Lines for Short Circuit  


DESCRIPTION

There may be a short circuit between the bus 5 CAN main wires and/or CAN branch wires when the resistance between terminals 15 (CA5H) and 16 (CA5L) of the central gateway ECU is below 54 Ω.

Detection Item Trouble Area

*1: w/ Pre-crash Safety System

*2: w/ TOYOTA Parking Assist-sensor System (for 8 Sensor Type)

*3: w/ Panoramic View Monitor System

*4: w/ Blind Spot Monitor System

*5: w/ Parking Assist Monitor System (for Camera built-in ECU)

Resistance between terminals 15 (CA5H) and 16 (CA5L) of central gateway ECU is below 54 Ω.
·

Short in bus 5 CAN main wires

·

Short in bus 5 CAN branch wires

·

Central gateway ECU

·

Forward recognition camera*1

·

Millimeter wave radar sensor assembly*1

·

Driving support ECU assembly*1

·

Clearance warning ECU assembly*2

·

Parking assist ECU*3

·

Blind spot monitor sensor LH*4

·

Television camera assembly*5

·

No. 9 CAN junction connector

·

No. 10 CAN junction connector



WIRING DIAGRAM

C334605E02
5.958,0.542 6.406,0.75 0.448,0.208 10 false CA5H 5.969,1.313 6.417,1.521 0.448,0.208 10 false CA5L 5.635,0.542 5.854,0.75 0.219,0.208 10 false 15 5.635,1.021 5.854,1.229 0.219,0.208 10 false 16 4.333,1.031 4.552,1.24 0.219,0.208 10 false 14 4.375,0.552 4.531,0.75 0.156,0.198 10 false 4 2.906,0.542 3.063,0.74 0.156,0.198 10 false 1 2.865,1.031 3.083,1.24 0.219,0.208 10 false 11 2.865,3.167 3.083,3.375 0.219,0.208 10 false 12 2.865,5.531 3.083,5.74 0.219,0.208 10 false 13 2.927,2.635 3.083,2.833 0.156,0.198 10 false 2 2.938,5 3.094,5.198 0.156,0.198 10 false 3 1.563,0.563 1.719,0.76 0.156,0.198 10 false 5 1.542,1.031 1.76,1.24 0.219,0.208 10 false 11 1.563,2.667 1.719,2.865 0.156,0.198 10 false 3 1.563,3.208 1.719,3.406 0.156,0.198 10 false 2 1.573,5 1.792,5.208 0.219,0.208 10 false 10 1.604,5.531 1.823,5.74 0.219,0.208 10 false 11 1,0.677 1.448,0.885 0.448,0.208 10 false CA1P 1.01,1.156 1.458,1.365 0.448,0.208 10 false CA1N 1,2.781 1.448,2.99 0.448,0.208 10 false CA2H 1,3.313 1.448,3.521 0.448,0.208 10 false CA2L 0.99,5.125 1.438,5.333 0.448,0.208 10 false CA2H 1.01,5.625 1.458,5.833 0.448,0.208 10 false CA2L 5.458,7.115 6.958,7.365 1.5,0.25 10 false Central Gateway ECU 5.458,6.938 5.906,7.146 0.448,0.208 10 false G170 2.927,7.104 5.115,7.313 2.188,0.208 10 false No. 9 CAN Junction Connector 2.917,6.938 3.365,7.146 0.448,0.208 10 false G174 0.125,1.396 0.573,1.604 0.448,0.208 10 false Q17 0.135,1.573 2.104,1.781 1.969,0.208 10 false Forward Recognition Camera* 0.083,3.76 2.792,4.021 2.708,0.26 10 false Millimeter Wave Radar Sensor Assembly* 0.083,3.583 0.531,3.792 0.448,0.208 10 false Z6 0.063,6.094 2.771,6.354 2.708,0.26 10 false Driving Support ECU Assembly* 0.073,5.938 0.563,6.208 0.49,0.271 10 false G168 0.115,8.104 2.219,8.385 2.104,0.281 10 false *: w/ Pre-crash Safety System

C334606E02
5.49,6.49 6.104,6.688 0.615,0.198 10 false G170 5.5,6.656 7.146,6.906 1.646,0.25 10 false Central Gateway ECU 4.375,1.458 4.531,1.656 0.156,0.198 10 false 5 4.344,1.99 4.563,2.188 0.219,0.198 10 false 15 2.938,1.469 3.094,1.667 0.156,0.198 10 false 6 2.875,1.99 3.094,2.188 0.219,0.198 10 false 16 4.375,4.74 4.531,4.938 0.156,0.198 10 false 3 4.344,5.281 4.563,5.479 0.219,0.198 10 false 13 2.917,4.74 3.073,4.938 0.156,0.198 10 false 1 2.875,5.281 3.094,5.479 0.219,0.198 10 false 11 2.656,2.615 4.74,2.854 2.083,0.24 10 false No. 9 CAN Junction Connector 2.698,6.635 4.781,6.875 2.083,0.24 10 false No. 10 CAN Junction Connector 2.646,2.458 3.26,2.656 0.615,0.198 10 false G174 2.698,6.458 3.302,6.75 0.604,0.292 10 false N36 1.552,1.458 1.771,1.656 0.219,0.198 10 false 17 1.563,2 1.781,2.198 0.219,0.198 10 false 18 1.188,1.583 1.458,1.802 0.271,0.219 10 false R1 1.188,2.094 1.458,2.313 0.271,0.219 10 false R2 0.094,2.521 2.469,2.771 2.375,0.25 10 false Clearance Warning ECU Assembly*1 0.094,2.344 0.708,2.542 0.615,0.198 10 false G166 0.99,4.885 1.448,5.094 0.458,0.208 10 false CANH 0.99,5.406 1.448,5.615 0.458,0.208 10 false CANL 1.552,5.271 1.771,5.469 0.219,0.198 10 false 13 1.542,4.74 1.76,4.938 0.219,0.198 10 false 12 0.427,5.844 1.333,6.052 0.906,0.208 10 false a2 0.438,6.031 1.927,6.448 1.49,0.417 10 false Parking Assist ECU*2 0.188,7.573 4.542,7.885 4.354,0.313 10 false *1: w/ TOYOTA Parking Assist-sensor System (for 8 Sensor Type) 0.177,7.927 2.875,8.188 2.698,0.26 10 false *2: w/ Panoramic View Monitor System

C334607E02
5.604,5.521 7.073,5.76 1.469,0.24 10 false Central Gateway ECU 5.594,5.344 6.031,5.542 0.438,0.198 10 false G170 2.719,5.469 4.823,5.719 2.104,0.25 10 false No. 10 CAN Junction Connector 2.719,5.323 3.156,5.521 0.438,0.198 10 false N36 0.083,5.146 2.188,5.396 2.104,0.25 10 false Television Camera Assembly*2 0.083,2.323 2.188,2.573 2.104,0.25 10 false Blind Spot Monitor Sensor LH*1 0.083,2.167 0.521,2.365 0.438,0.198 10 false R1 0.094,4.969 0.531,5.281 0.438,0.313 10 false c2 2.917,1.188 3.073,1.385 0.156,0.198 10 false 4 2.927,4.073 3.083,4.271 0.156,0.198 10 false 5 4.365,4.104 4.521,4.302 0.156,0.198 10 false 2 2.865,1.719 3.094,1.938 0.229,0.219 10 false 14 2.875,4.563 3.104,4.781 0.229,0.219 10 false 15 4.323,4.563 4.552,4.781 0.229,0.219 10 false 12 1.552,1.219 1.708,1.417 0.156,0.198 10 false 2 1.542,1.75 1.698,1.948 0.156,0.198 10 false 7 5.688,4.115 5.844,4.313 0.156,0.198 10 false 9 5.635,4.573 5.865,4.792 0.229,0.219 10 false 24 1.563,4.104 1.719,4.302 0.156,0.198 10 false 4 1.573,4.594 1.729,4.792 0.156,0.198 10 false 1 5.969,4.094 6.479,4.292 0.51,0.198 10 false CAXH 5.99,4.844 6.5,5.042 0.51,0.198 10 false CAXL 0.99,4.24 1.448,4.448 0.458,0.208 10 false CANH 1,4.698 1.458,4.906 0.458,0.208 10 false CANL 1,1.313 1.458,1.521 0.458,0.208 10 false CA1P 1.01,1.865 1.469,2.073 0.458,0.208 10 false CA1N 0.177,6.583 2.344,6.813 2.167,0.229 10 false *1: w/ Blind Spot Monitor System 0.167,6.979 4.208,7.24 4.042,0.26 10 false *2: w/ Parking Assist Monitor System (for Camera built-in ECU)

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU)>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR SHORT IN CAN BUS WIRES (NO. 9 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) battery terminal.

C343209C19
4.771,0.792 5.271,1.042 0.5,0.25 2.531,0.135 2.719,0.135 2.719,0.135 3.198,0.854 true 2.375,0.333 2.563,0.333 2.563,0.333 3.01,0.854 true 2.125,1.125 2.313,1.125 2.313,1.125 2.604,1.01 true 2.208,0.51 2.396,0.51 2.396,0.51 2.833,0.865 true 2.115,0.729 2.302,0.729 2.302,0.729 2.615,0.885 true 2.24,1.302 2.427,1.302 2.427,1.302 2.813,1.031 true 2.406,1.469 2.594,1.469 2.594,1.469 3.01,1.021 true 2.583,1.656 2.771,1.656 2.771,1.656 3.198,1.042 true 4.052,0.135 3.844,0.135 3.844,0.135 3.448,0.844 true 4.281,0.333 4.073,0.333 4.073,0.333 3.781,0.865 true 4.094,1.646 3.885,1.646 3.885,1.646 3.427,1.01 true 4.229,1.448 4.021,1.448 4.021,1.448 3.75,1.021 true 0.135,0.094 0.448,0.292 0.313,0.198 10 false *a 1.948,0.052 2.521,0.26 0.573,0.208 10 false CANH*e 1.688,1.229 2.25,1.438 0.563,0.208 10 false CANL*c 4.833,0.844 5.292,1.042 0.458,0.198 10 false G174 1.781,0.26 2.354,0.469 0.573,0.208 10 false CANH*d 1.573,1.052 2.135,1.26 0.563,0.208 10 false CANL*b 1.542,0.646 2.115,0.854 0.573,0.208 10 false CANH*b 1.635,0.427 2.208,0.635 0.573,0.208 10 false CANH*c 1.865,1.385 2.427,1.594 0.563,0.208 10 false CANL*d 2.042,1.573 2.604,1.781 0.563,0.208 10 false CANL*e 4.094,0.042 4.667,0.25 0.573,0.208 10 false CANH*f 4.323,0.26 4.896,0.469 0.573,0.208 10 false CANH*g 4.271,1.375 4.833,1.583 0.563,0.208 10 false CANL*g 4.156,1.573 4.719,1.781 0.563,0.208 10 false CANL*f
*a Front view of wire harness connector
(to No. 9 CAN Junction Connector)
*b to Forward Recognition Camera (w/ Pre-crash Safety System)
*c to Millimeter Wave Radar Sensor Assembly (w/ Pre-crash Safety System) *d to Driving Support ECU Assembly (w/ Pre-crash Safety System)
*e to Central Gateway ECU *f to No. 10 CAN Junction Connector
*g to Clearance Warning ECU Assembly (w/ TOYOTA Parking Assist-sensor System [for 8 Sensor Type]) - -



b.

Disconnect the No. 9 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connect to

*1: w/ Pre-crash Safety System

*2: w/ TOYOTA Parking Assist-sensor System (for 8 Sensor Type)

G174-1 (CANH) - G174-11 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Forward recognition camera*1
G174-2 (CANH) - G174-12 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Millimeter wave radar sensor assembly*1
G174-3 (CANH) - G174-13 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Driving support ECU assembly*1
G174-4 (CANH) - G174-14 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Central gateway ECU
G174-5 (CANH) - G174-15 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 10 CAN junction connector
G174-6 (CANH) - G174-16 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Clearance warning ECU assembly*2



Result:
Result Proceed to
OK A
NG (No. 10 CAN junction connector CAN main wire) B
NG (Central gateway ECU CAN main wire) C
NG (ECU or sensor CAN branch wires) D



A

REPLACE NO. 9 CAN JUNCTION CONNECTOR

B

2.CONNECT CONNECTOR

C

6.CONNECT CONNECTOR

D

8.CHECK FOR SHORT IN CAN BUS WIRES (ECU, SENSOR)
2.CONNECT CONNECTOR
a.

Reconnect the G174 No. 9 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

3.CHECK FOR SHORT IN CAN BUS WIRES (NO. 10 CAN JUNCTION CONNECTOR)
3.CHECK FOR SHORT IN CAN BUS WIRES (NO. 10 CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 10 CAN junction connector.

C343209C20
4.771,0.792 5.271,1.042 0.5,0.25 2.531,0.135 2.719,0.135 2.719,0.135 3.198,0.854 true 2.375,0.333 2.563,0.333 2.563,0.333 3.01,0.854 true 2.125,1.125 2.313,1.125 2.313,1.125 2.604,1.01 true 2.208,0.51 2.396,0.51 2.396,0.51 2.833,0.865 true 2.115,0.729 2.302,0.729 2.302,0.729 2.615,0.885 true 2.24,1.302 2.427,1.302 2.427,1.302 2.813,1.031 true 2.406,1.469 2.594,1.469 2.594,1.469 3.01,1.021 true 2.583,1.656 2.771,1.656 2.771,1.656 3.198,1.042 true 4.052,0.135 3.844,0.135 3.844,0.135 3.448,0.844 true 4.094,1.646 3.885,1.646 3.885,1.646 3.427,1.01 true 0.135,0.094 0.448,0.292 0.313,0.198 10 false *a 1.948,0.052 2.521,0.26 0.573,0.208 10 false CANH*e 1.688,1.229 2.25,1.438 0.563,0.208 10 false CANL*c 4.906,0.844 5.438,1.219 0.531,0.375 10 false N36 1.781,0.26 2.354,0.469 0.573,0.208 10 false CANH*d 1.573,1.052 2.135,1.26 0.563,0.208 10 false CANL*b 1.542,0.646 2.115,0.854 0.573,0.208 10 false CANH*b 1.635,0.427 2.208,0.635 0.573,0.208 10 false CANH*c 1.865,1.385 2.427,1.594 0.563,0.208 10 false CANL*d 2.042,1.573 2.604,1.781 0.563,0.208 10 false CANL*e 4.094,0.042 4.667,0.25 0.573,0.208 10 false CANH*f 4.156,1.573 4.719,1.781 0.563,0.208 10 false CANL*f
*a Front view of wire harness connector
(to No. 10 CAN Junction Connector)
*b to Parking Assist ECU (w/ Panoramic View Monitor System)
*c to Central Gateway ECU *d to No. 9 CAN Junction Connector
*e to Blind Spot Monitor Sensor LH (w/ Blind Spot Monitor System) *f to Television Camera Assembly (w/ Parking Assist Monitor System [for Camera built-in ECU])



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connect to

*1: w/ Panoramic View Monitor System

*2: w/ Blind Spot Monitor System

*3: w/ Parking Assist Monitor System (for Camera built-in ECU)

N36-1 (CANH) - N36-11 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Parking assist ECU*1
N36-2 (CANH) - N36-12 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Central gateway ECU
N36-3 (CANH) - N36-13 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 9 CAN junction connector
N36-4 (CANH) - N36-14 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Blind spot monitor sensor LH*2
N36-5 (CANH) - N36-15 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Television camera assembly*3



Result:
Result Proceed to
OK A
NG (No. 9 CAN junction connector CAN main wire) B
NG (Central gateway ECU CAN main wire) C
NG (ECU or sensor CAN branch wires) D



A

REPLACE NO. 10 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 10 CAN JUNCTION CONNECTOR - NO. 9 CAN JUNCTION CONNECTOR)

C

4.CONNECT CONNECTOR

D

8.CHECK FOR SHORT IN CAN BUS WIRES (ECU, SENSOR)
4.CONNECT CONNECTOR
a.

Reconnect the N36 No. 10 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

5.CHECK FOR SHORT IN CAN BUS WIRES (CENTRAL GATEWAY ECU)
5.CHECK FOR SHORT IN CAN BUS WIRES (CENTRAL GATEWAY ECU)
a.
C326490C28
1.5,0.167 2.031,0.385 0.531,0.219 1.688,1.854 1.885,1.854 1.885,1.854 2.74,1 true 2.438,2.042 2.635,2.042 2.635,2.042 2.865,1.208 true 0.135,0.094 0.438,0.427 0.302,0.333 10 false *a 1.583,0.198 2.188,0.5 0.604,0.302 10 false G170 1.25,1.771 1.688,1.938 0.438,0.167 10 false CAXH 2.01,1.969 2.427,2.135 0.417,0.167 10 false CAXL
*a Front view of wire harness connector
(to Central Gateway ECU)


Disconnect the central gateway ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G170-9 (CAXH) - G170-24 (CAXL) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (CENTRAL GATEWAY ECU - NO. 10 CAN JUNCTION CONNECTOR)

6.CONNECT CONNECTOR
a.

Reconnect the G174 No. 9 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

7.CHECK FOR SHORT IN CAN BUS WIRES (CENTRAL GATEWAY ECU)
7.CHECK FOR SHORT IN CAN BUS WIRES (CENTRAL GATEWAY ECU)
a.
C326490C29
1.5,0.167 2.031,0.385 0.531,0.219 0.646,1.802 0.844,1.802 0.844,1.802 1.344,1.198 true 0.75,2.042 0.948,2.042 0.948,2.042 1.51,1.208 true 0.135,0.094 0.438,0.427 0.302,0.333 10 false *a 1.583,0.198 2.188,0.5 0.604,0.302 10 false G170 0.219,1.729 0.656,1.896 0.438,0.167 10 false CA5H 0.354,1.969 0.792,2.135 0.438,0.167 10 false CA5L
*a Front view of wire harness connector
(to Central Gateway ECU)


Disconnect the central gateway ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G170-15 (CA5H) - G170-16 (CA5L) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (CENTRAL GATEWAY ECU - NO. 9 CAN JUNCTION CONNECTOR)

8.CHECK FOR SHORT IN CAN BUS WIRES (ECU, SENSOR)
a.
C334654C04
1.469,0.26 1.969,0.51 0.5,0.25 2.406,1.844 2.24,1.844 2.24,1.844 1.927,1.125 true 2.323,2.031 2.156,2.031 2.156,2.031 1.844,1.135 true 0.115,0.052 0.469,0.365 0.354,0.313 10 false *a 1.552,0.281 2.031,0.594 0.479,0.313 10 false G170 2.458,1.76 3.042,1.99 0.583,0.229 10 false CA5H 2.354,1.958 2.958,2.135 0.604,0.177 10 false CA5L
*a Component with harness connected
(Central Gateway ECU)


Reconnect the CAN junction connector.


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the short circuited CAN branch wire is connected.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G170-15 (CA5H) - G170-16 (CA5L) Cable disconnected from negative (-) battery terminal 54 to 69 Ω


HINT:

If the resistance becomes normal (between 54 and 69 Ω) when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.



Result:
Proceed to
OK
NG



OK

REPLACE CORRESPONDING ECU OR SENSOR

NG

REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR CAN BRANCH WIRES OR CONNECTOR