The driving support ECU assembly will store this DTC when no signals can be received from the ECUs that have been memorized as those that are connected to local bus.
When the driving support ECU assembly receives a response signal from the ECUs connected to local bus, the driving support ECU assembly recognizes and memorizes that the ECU is connected to local bus. Based on this memorized data, the driving support ECU assembly monitors for malfunctions in the ECUs connected to local bus when communicating with those ECUs. If the driving support ECU assembly cannot receive response signals from the ECUs that have been memorized as those connected to local bus, the driving support ECU assembly determines that a malfunction exists.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from |
|---|---|---|---|---|
| U1002 | Lost Communication with Gateway Module (Sensor Bus) | Driving support ECU assembly cannot receive signals from all ECUs that have been memorized as those connected to local bus. | ·
Open or short in local bus CAN main wire or connector ·
Open or short in local bus CAN branch wire or connector ·
Driving support ECU assembly ·
Millimeter wave radar sensor assembly ·
Forward recognition camera ·
No. 8 CAN junction connector |
Driving support ECU assembly |
For vehicles with a pre-crash safety system.
Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.
Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
DTC check procedure: Turn the ignition switch to ON and wait at least 20 seconds.
After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.
Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.
| *a | Component with harness connected
(Driving Support ECU Assembly) |
| *b | Front view of DLC3 |
Disconnect the cable from the negative (-) battery terminal.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Resistance: Malfunction |
|---|---|---|---|
| G168-8 (CA1P) - G168-9 (CA1N) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω | Below 53 Ω: Short in line |
| G168-8 (CA1P) - G168-9 (CA1N) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω | Higher than 70 Ω: Open in CAN main bus line |
| G168-8 (CA1P) - G14-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: +B short |
| G168-9 (CA1N) - G14-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: +B short |
| G168-8 (CA1P) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: Ground short |
| G168-9 (CA1N) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: Ground short |
| Result | Proceed to |
|---|---|
| OK | A |
| NG
- Open in CAN main wire |
B |
| NG
- Short in CAN bus wire |
C |
| NG
- +B short - Ground short |
D |
A
B
C
D
Clear the DTCs.
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC U1002 is output from driving support ECU assembly | A |
| Other DTC is output | B |
A
B
| *a | Rear view of wire harness connector
(to No. 8 CAN Junction Connector) |
| *b | to Forward Recognition Camera |
| *c | to Millimeter Wave Radar Sensor Assembly |
Disconnect the No. 8 CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G173-6 (CANH) - G173-17 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| G173-7 (CANH) - G173-18 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (to forward recognition camera CAN main wire) | B |
| NG (to millimeter wave radar sensor assembly CAN main wire) | C |
A
B
C
Reconnect the G173 No. 8 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Front view of wire harness connector
(to Forward Recognition Camera) |
Disconnect the forward recognition camera connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Q17-6 (CANH) - Q17-12 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the G173 No. 8 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly) |
Disconnect the millimeter wave radar sensor assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Z6-5 (CA1P) - Z6-6 (CA1N) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Rear view of wire harness connector
(to No. 8 CAN Junction Connector) |
| *b | to Driving Support ECU Assembly |
| *c | to Forward Recognition Camera |
| *d | to Millimeter Wave Radar Sensor Assembly |
Disconnect the No. 8 CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G173-5 (CANH) - G173-16 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G173-6 (CANH) - G173-17 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| G173-7 (CANH) - G173-18 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (to forward recognition camera CAN main wire) | B |
| NG (to millimeter wave radar sensor assembly CAN main wire) | C |
| NG (to driving support ECU assembly CAN branch wire) | D |
A
B
C
D
Reconnect the G173 No. 8 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Front view of wire harness connector
(to Forward Recognition Camera) |
Disconnect the forward recognition camera connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Q17-6 (CANH) - Q17-12 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the G173 No. 8 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly) |
Disconnect the millimeter wave radar sensor assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Z6-5 (CA1P) - Z6-6 (CA1N) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the G173 No. 8 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Front view of wire harness connector
(to Driving Support ECU Assembly) |
Disconnect the driving support ECU assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G168-8 (CA1P) - G168-9 (CA1N) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the No. 8 CAN junction connector.
| *a | Rear view of wire harness connector
(to No. 8 CAN Junction Connector) |
*b | Front view of DLC3 |
| *c | to Driving Support ECU Assembly | *d | to Forward Recognition Camera |
| *e | to Millimeter Wave Radar Sensor Assembly | - | - |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G173-5 (CANH) - G14-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| G173-16 (CANL) - G14-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| G173-5 (CANH) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G173-16 (CANL) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G173-6 (CANH) - G14-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| G173-17 (CANL) - G14-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| G173-6 (CANH) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G173-17 (CANL) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G173-7 (CANH) - G14-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| G173-18 (CANL) - G14-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| G173-7 (CANH) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G173-18 (CANL) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (to forward recognition camera CAN main wire) | B |
| NG (to millimeter wave radar sensor assembly CAN main wire) | C |
| NG (to driving support ECU assembly CAN branch wire) | D |
A
B
C
D
Reconnect the G173 No. 8 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Front view of wire harness connector
(to Forward Recognition Camera) |
| *b | Front view of DLC3 |
Disconnect the forward recognition camera connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Q17-6 (CANH) - G14-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| Q17-12 (CANL) - G14-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| Q17-6 (CANH) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Q14-12 (CANL) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the G173 No. 8 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly) |
| *b | Front view of DLC3 |
Disconnect the millimeter wave radar sensor assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Z6-5 (CA1P) - G14-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| Z6-6 (CA1N) - G14-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| Z6-5 (CA1P) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Z6-6 (CA1N) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the G173 No. 8 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Front view of wire harness connector
(to Driving Support ECU Assembly) |
| *b | Front view of DLC3 |
Disconnect the driving support ECU assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G168-8 (CA1P) - G14-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| G168-9 (CA1N) - G14-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| G168-8 (CA1P) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G168-9 (CA1N) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG