Home › Drivetrain › U760F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM › from 2015.10
RM3090E _52 Drivetrain _008753 U760F AUTOMATIC TRANSMISSION / TRANSAXLE _0058021 AUTOMATIC TRANSAXLE SYSTEM C

U760F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P0705  Transmission Range Sensor Circuit Malfunction (PRNDL Input)  


DESCRIPTION

The park/neutral position switch assembly detects the shift lever position and sends signals to the ECM.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0705 Transmission Range Sensor Circuit Malfunction (PRNDL Input) One of the following conditions (A) through (C) is met (2-trip detection logic)
(A) Either of the following conditions 1, 2 or 3 is met:
1. Any 2 or more signals of the following are ON simultaneously:
·

P input signal is ON.

·

R input signal is ON.

·

D input signal is ON.


2. Any 2 or more signals of the following are ON simultaneously:
·

N input signal is ON.

·

R input signal is ON.

·

D input signal is ON.


3. Any 2 or more signals of the following are ON simultaneously:
·

NSW input signal is ON.

·

R input signal is ON.

·

D input signal is ON.


(B) All switches are OFF simultaneously for P, N, NSW, R and D.
(C) When any of following conditions is met for 2.0 sec. or more in the S position:
·

P input signal is ON.

·

N input signal is ON.

·

NSW input signal is ON.

·

R input signal is ON.


·

Open or short in park/neutral position switch assembly circuit

·

Park/neutral position switch assembly

·

Transmission control switch (transmission floor shift assembly)

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

These DTCs indicate a problem with the park/neutral position switch assembly and the wire harness in the park/neutral position switch assembly circuit.

The park/neutral position switch assembly detects the shift lever position and sends signals to the ECM.

For safety, the park/neutral position switch assembly detects the shift lever position so that the engine can be started only when the shift lever is in P or N.

The park/neutral position switch assembly sends a signal to the ECM according to the shift lever position (P, N, NSW, R, D or S). The ECM determines that there is a problem with the switch or related parts if it receives more than 1 position signal simultaneously. The ECM will turn on the MIL and store the DTC.

WIRING DIAGRAM

C277058C01
2.333,5.875 4.354,6.156 2.021,0.281 10 false Transmission Control Switch 2.323,5.688 2.781,5.885 0.458,0.198 10 false G36 0.208,5.167 1.958,5.448 1.75,0.281 10 false from ECU-IG NO. 1 Fuse 0.51,2.688 1.896,2.927 1.385,0.24 10 false from GAUGE Fuse 0.135,1.167 1.865,1.396 1.729,0.229 10 false to ST*1, ST NO. 1*2 Relay 2.313,4.292 4.313,4.563 2,0.271 10 false Park/Neutral Position Switch 2.302,4.094 2.76,4.292 0.458,0.198 10 false B101 2.792,1.063 3.125,1.281 0.333,0.219 10 false L 2.563,1.323 2.896,1.542 0.333,0.219 10 false 9 3.552,1.063 3.885,1.281 0.333,0.219 10 false B 3.792,1.313 4.125,1.531 0.333,0.219 10 false 4 3.5,1.656 3.844,1.875 0.344,0.219 10 false DL 3.781,1.917 4.115,2.135 0.333,0.219 10 false 7 3.5,2.26 3.844,2.479 0.344,0.219 10 false NL 3.792,2.521 4.125,2.74 0.333,0.219 10 false 8 3.5,2.865 3.844,3.083 0.344,0.219 10 false RL 3.781,3.125 4.115,3.344 0.333,0.219 10 false 2 3.479,3.469 3.823,3.688 0.344,0.219 10 false PL 3.792,3.719 4.125,3.938 0.333,0.219 10 false 3 2.781,2.552 3.115,2.771 0.333,0.219 10 false RB 2.563,2.833 2.896,3.052 0.333,0.219 10 false 1 5.25,1.188 5.625,1.396 0.375,0.208 10 false B77 5.625,1.198 6.083,1.396 0.458,0.198 10 false NSW 5.313,0.969 5.563,1.198 0.25,0.229 10 false 63 5.313,1.573 5.563,1.802 0.25,0.229 10 false 67 5.25,1.781 5.646,2.01 0.396,0.229 10 false B77 5.635,1.792 6.094,1.99 0.458,0.198 10 false D 5.26,2.385 5.635,2.604 0.375,0.219 10 false B77 5.271,2.99 5.615,3.208 0.344,0.219 10 false B77 5.26,3.583 5.615,3.823 0.354,0.24 10 false B77 5.25,5.177 5.615,5.406 0.365,0.229 10 false A62 5.313,2.177 5.563,2.406 0.25,0.229 10 false 71 5.302,2.771 5.552,3 0.25,0.229 10 false 66 5.313,3.375 5.563,3.604 0.25,0.229 10 false 70 5.313,4.979 5.563,5.208 0.25,0.229 10 false 27 5.646,2.385 6.104,2.583 0.458,0.198 10 false N 5.635,2.979 6.094,3.177 0.458,0.198 10 false R 5.635,3.583 6.094,3.781 0.458,0.198 10 false P 5.615,5.167 6.073,5.365 0.458,0.198 10 false S 3.563,5.063 3.938,5.24 0.375,0.177 10 false S 2.792,5.063 3.167,5.24 0.375,0.177 10 false IG 3.781,5.302 4.115,5.521 0.333,0.219 10 false 5 2.583,5.313 2.917,5.531 0.333,0.219 10 false 4 5.792,5.896 6.24,6.135 0.448,0.24 10 false ECM 0.104,6.26 3.625,6.458 3.521,0.198 10 false *1: w/ Canister Pump Module 0.104,6.521 3.625,6.719 3.521,0.198 10 false *2: w/o Canister Pump Module

CAUTION / NOTICE / HINT

NOTICE:

Perform registration and/or initialization when parts related to the automatic transaxle are replaced.

Click hereDrivetrain>U760F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>PRECAUTION


DATA LIST


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List.


g.

According to the display on the GTS, read the Data List.

Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Neutral Position SW Signal PNP switch status ON or OFF
·

ON: Shift lever in P or N

·

OFF: Shift lever not in P or N


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
Shift SW Status (P Range) PNP switch status ON or OFF
·

ON: Shift lever in P

·

OFF: Shift lever not in P


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
Shift SW Status (R Range) PNP switch status ON or OFF
·

ON: Shift lever in R

·

OFF: Shift lever not in R


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
Shift SW Status (N Range) PNP switch status ON or OFF
·

ON: Shift lever in N

·

OFF: Shift lever not in N


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
Sports Mode Selection SW Sport mode select switch status ON or OFF
·

ON: Shift lever in S, "+" or "-"

·

OFF: Shift lever not in S, "+" or "-"


-
Shift SW Status (D Range) PNP switch status ON or OFF
·

ON: Shift lever in D or S

·

OFF: Shift lever not in D or S


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
Powertrain > Engine and ECT > Data List
Tester Display
Neutral Position SW Signal
Shift SW Status (P Range)
Shift SW Status (R Range)
Shift SW Status (N Range)
Sports Mode Selection SW
Shift SW Status (D Range)
50003 234 147,125,126,127,133,128


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (ECU-IG NO. 1 FUSE - PARK/NEUTRAL POSITION SWITCH)
a.

Disconnect the park/neutral position switch connector.


b.
C330140C12
0.438,0.958 0.885,1.24 0.448,0.281 1.625,1 2.021,0.396 true 2.073,0.313 2.385,0.51 0.313,0.198 10 false RB 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a 0.5,1.021 0.969,1.219 0.469,0.198 10 false B101
*a Front view of wire harness connector
(to Park/Neutral Position Switch Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B101-1 (RB) - Body ground Ignition switch ON 11 to 14 V
B101-1 (RB) - Body ground Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (NSW TERMINAL VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (NSW TERMINAL VOLTAGE)
a.

Disconnect the park/neutral position switch connector.


b.
C330140C13
0.438,0.958 0.885,1.24 0.448,0.281 2.031,1 2.292,0.396 true 2.354,0.313 2.667,0.51 0.313,0.198 10 false B 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a 0.5,1.021 0.969,1.219 0.469,0.198 10 false B101
*a Front view of wire harness connector
(to Park/Neutral Position Switch Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B101-4 (B) - Body ground Ignition switch ON 11 to 14 V
B101-4 (B) - Body ground Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

3.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

NG

7.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)
3.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.

Disconnect the park/neutral position switch connector.


b.
C197712C16
1.271,0.938 0.833,0.427 true 1.583,0.938 1.646,0.438 true 1.833,0.938 2.115,0.427 true 1.333,1.302 0.948,1.719 true 1.698,1.292 2.042,1.76 true 1.406,0.938 1.25,0.427 true 1.469,1.302 1.417,1.719 true 0.073,0.073 0.333,0.25 0.26,0.177 10 *a 0.656,0.333 0.875,0.542 0.219,0.208 10 B 1.698,0.333 1.948,0.531 0.25,0.198 10 RL 2.167,0.333 2.448,0.531 0.281,0.198 10 RB 2.094,1.667 2.323,1.865 0.229,0.198 10 DL 0.813,1.667 1.042,1.865 0.229,0.198 10 L 1.031,0.333 1.281,0.531 0.25,0.198 10 PL 1.208,1.667 1.438,1.865 0.229,0.198 10 NL
*a Component without harness connected
(Park/Neutral Position Switch Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
·

1 (RB) - 3 (PL)

·

4 (B) - 9 (L)


Shift lever in P Below 1 Ω
1 (RB) - 2 (RL) Shift lever in R Below 1 Ω
·

1 (RB) - 8 (NL)

·

4 (B) - 9 (L)


Shift lever in N Below 1 Ω
1 (RB) - 7 (DL)
·

Shift lever in D

·

Shift lever in S, "+" or "-"


Below 1 Ω
·

1 (RB) - 3 (PL)

·

4 (B) - 9 (L)


Shift lever not in P 10 kΩ or higher
1 (RB) - 2 (RL) Shift lever not in R 10 kΩ or higher
·

1 (RB) - 8 (NL)

·

4 (B) - 9 (L)


Shift lever not in N 10 kΩ or higher
1 (RB) - 7 (DL)
·

Shift lever not in D

·

Shift lever not in S, "+" or "-"


10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (ECU-IG NO. 1 FUSE - TRANSMISSION CONTROL SWITCH)

NG

4.CHECK HARNESS AND CONNECTOR (ECU-IG NO. 1 FUSE - TRANSMISSION CONTROL SWITCH)
a.

Disconnect the transmission control switch connector.


b.
C267936C06
0.229,0.979 0.583,1.24 0.354,0.26 2.646,1.875 2,1.406 true 2.719,1.802 3.031,2 0.313,0.198 10 false IG 0.271,1.031 0.583,1.229 0.313,0.198 10 false G36 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Transmission Control Switch)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G36-4 (IG) - Body ground Ignition switch ON 11 to 14 V
G36-4 (IG) - Body ground Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

5.INSPECT TRANSMISSION CONTROL SWITCH (TRANSMISSION FLOOR SHIFT ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT TRANSMISSION CONTROL SWITCH (TRANSMISSION FLOOR SHIFT ASSEMBLY)
a.

Disconnect the transmission control switch connector.


b.
C277025C03
0.802,1.802 1.219,1.385 true 1.427,1.781 1.479,1.396 true 1.354,1.833 1.667,2.031 0.313,0.198 10 IG 0.74,1.823 1.052,2.021 0.313,0.198 10 S 0.104,0.104 0.417,0.302 0.313,0.198 10 *a
*a Component without harness connected
(Transmission Control Switch)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (IG) - 5 (S) Shift lever in S, "+" or "-" Below 1 Ω
4 (IG) - 5 (S) Shift lever not in S, "+"or "-" 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH, TRANSMISSION CONTROL SWITCH - ECM)

NG

REPLACE TRANSMISSION FLOOR SHIFT ASSEMBLY

6.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH, TRANSMISSION CONTROL SWITCH - ECM)
a.

Disconnect the ECM connectors.


b.
C278714C01
1.479,0.25 1.833,0.49 0.354,0.24 1.479,2.26 1.833,2.5 0.354,0.24 0.354,1.708 0.635,1.104 true 0.75,1.938 0.708,1.104 true 2.625,4.188 2.406,3.344 true 1.583,1.917 1.031,1.104 true 1.135,1.698 0.969,1.104 true 1.542,0.292 2,0.49 0.458,0.198 10 false B77 1.542,2.302 2,2.5 0.458,0.198 10 false A62 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a 1,1.729 1.49,1.927 0.49,0.198 10 false 70 (P) 0.156,1.729 0.646,1.927 0.49,0.198 10 false 66 (R) 1.448,1.969 1.938,2.167 0.49,0.198 10 false 71 (N) 0.573,1.969 1.063,2.167 0.49,0.198 10 false 67 (D) 2.479,4.24 2.969,4.438 0.49,0.198 10 false 27 (S)
*a Front view of wire harness connector
(to ECM)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
B77-70 (P) - Body ground
·

Ignition switch ON

·

Shift lever in P


11 to 14 V
B77-66 (R) - Body ground
·

Ignition switch ON

·

Shift lever in R


11 to 14 V*
B77-71 (N) - Body ground
·

Ignition switch ON

·

Shift lever in N


11 to 14 V
B77-67 (D) - Body ground
·

Ignition switch ON

·

Shift lever in D


11 to 14 V
A62-27 (S) - Body ground
·

Ignition switch ON

·

Shift lever in S, "+"or "-"


11 to 14 V
B77-70 (P) - Body ground
·

Ignition switch ON

·

Shift lever not in P


Below 1 V
B77-66 (R) - Body ground
·

Ignition switch ON

·

Shift lever not in R


Below 1 V
B77-71 (N) - Body ground
·

Ignition switch ON

·

Shift lever not in N


Below 1 V
B77-67 (D) - Body ground
·

Ignition switch ON

·

Shift lever not in D


Below 1 V
A62-27 (S) - Body ground
·

Ignition switch ON

·

Shift lever not in S, "+" or "-"


Below 1 V


HINT:

*: The voltage will drop slightly due to the illumination of the back-up light.



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)
a.

Disconnect the B101 park/neutral position switch connector.


b.

Disconnect the B77 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B101-4 (B) - B77-63 (NSW) Always Below 1 Ω
B101-4 (B) - Body ground Always 10 kΩ or higher
B77-63 (NSW) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR