Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for RHD without Central Gateway ECU) › 2015.10–2016.08
RM3090E _57 Power Source / Network _008434 NETWORKING _0221949 CAN COMMUNICATION SYSTEM(for RHD without Central Gateway ECU) U

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD without Central Gateway ECU)  TERMINALS OF ECU  


HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system.


NOTICE:
·

Before measuring the resistance, leave the vehicle for at least 1 minute and do not operate the ignition switch, any switches or any doors. If doors need to be opened in order to check connectors, open the doors and leave them open.

·

After turning the cable disconnected from negative (-) battery terminal, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION





JUNCTION CONNECTOR


a.

No. 6 CAN Junction Connector

C235392C42
4.385,1.25 4.875,1.49 0.49,0.24 3.656,1.302 3.083,0.458 3.083,0.458 2.833,0.458 true 3.573,1.333 2.906,0.719 2.906,0.719 2.677,0.719 true 3.438,1.313 2.906,1 2.906,1 2.656,1 true 3.448,1.458 2.917,1.875 2.917,1.875 2.667,1.875 true 3.563,1.458 3.083,2.083 3.083,2.083 2.833,2.083 true 3.646,1.49 3.25,2.25 3.25,2.25 3,2.25 true 4.5,0.969 4.313,0.969 4.313,0.969 4.031,1.313 true 4.396,0.667 4.208,0.667 4.208,0.667 3.938,1.313 true 4.26,0.417 4.073,0.417 4.073,0.417 3.833,1.313 true 4.51,1.844 4.323,1.844 4.323,1.844 4.031,1.448 true 4.313,2.063 4.125,2.063 4.125,2.063 3.917,1.479 true 4.25,2.396 4.063,2.396 4.063,2.396 3.833,1.469 true 3.75,1.469 3.438,2.448 3.438,2.448 3.188,2.448 true 3.729,1.313 3.354,0.198 3.354,0.198 3.104,0.198 true 0.083,0.052 1,0.25 0.917,0.198 10 false *a 2.104,0.896 3.021,1.094 0.917,0.198 10 false CANH*h 2.656,2.354 3.573,2.552 0.917,0.198 10 false CANL*e 2.135,1.76 3.052,1.958 0.917,0.198 10 false CANL*h 4.313,2.271 5.229,2.469 0.917,0.198 10 false CANL*d 4.448,1.271 5.365,1.469 0.917,0.198 10 false G188 4.563,0.865 5.479,1.063 0.917,0.198 10 false CANH*b 4.438,0.573 5.354,0.771 0.917,0.198 10 false CANH*c 4.302,0.313 5.219,0.51 0.917,0.198 10 false CANH*d 4.573,1.719 5.49,1.917 0.917,0.198 10 false CANL*b 4.365,1.948 5.281,2.146 0.917,0.198 10 false CANL*c 2.542,0.104 3.458,0.302 0.917,0.198 10 false CANH*e 2.313,1.948 3.229,2.146 0.917,0.198 10 false CANL*g 2.323,0.375 3.24,0.573 0.917,0.198 10 false CANH*f 2.146,0.625 3.063,0.823 0.917,0.198 10 false CANH*g 2.5,2.146 3.417,2.344 0.917,0.198 10 false CANL*f
*a Rear view of wire harness connector
(to No. 6 CAN Junction Connector)
*b for Main Body ECU (Multiplex Network Body ECU)
*c for Air Conditioning Amplifier Assembly *d for Brake Actuator Assembly (Skid Control ECU)
*e for No. 7 CAN Junction Connector *f for Engine Stop and Start ECU (w/ Stop and Start System)
*g for Airbag Sensor Assembly *h for ECM


No. 6 CAN Junction Connector Wiring Color Connect to

*: w/ Stop and Start System

G188-1 (CANH) G Main body ECU (multiplex network body ECU)
G188-12 (CANL) W
G188-2 (CANH) B Air conditioning amplifier assembly
G188-13 (CANL) W
G188-3 (CANH) GR Brake actuator assembly (skid control ECU)
G188-14 (CANL) W
G188-4 (CANH) V No. 7 CAN junction connector
G188-15 (CANL) W
G188-5 (CANH) LG Engine stop and start ECU*
G188-16 (CANL) W
G188-6 (CANH) BR Airbag sensor assembly
G188-17 (CANL) W
G188-7 (CANH) Y ECM
G188-18 (CANL) W


b.

No. 7 CAN Junction Connector

C235392C48
4.385,1.25 4.875,1.49 0.49,0.24 3.552,1.302 2.979,0.458 2.979,0.458 2.729,0.458 true 3.375,1.302 2.906,0.719 2.906,0.719 2.677,0.719 true 3.26,1.323 2.823,1.156 2.823,1.156 2.573,1.156 true 3.26,1.49 2.844,1.74 2.844,1.74 2.594,1.74 true 3.375,1.5 2.885,1.979 2.885,1.979 2.635,1.979 true 3.552,1.448 3.156,2.208 3.156,2.208 2.906,2.208 true 4.5,0.969 4.313,0.969 4.313,0.969 4.031,1.313 true 4.396,0.667 4.208,0.667 4.208,0.667 3.938,1.313 true 4.26,0.417 4.073,0.417 4.073,0.417 3.833,1.313 true 4.51,1.844 4.323,1.844 4.323,1.844 4.031,1.448 true 4.313,2.063 4.125,2.063 4.125,2.063 3.917,1.479 true 4.25,2.396 4.063,2.396 4.063,2.396 3.823,1.469 true 3.74,1.479 3.417,2.396 3.417,2.396 3.167,2.396 true 3.719,1.323 3.24,0.229 3.24,0.229 2.99,0.229 true 0.083,0.052 1,0.25 0.917,0.198 10 false *a 2.635,2.281 3.552,2.479 0.917,0.198 10 false CANL*e 2.063,1.625 2.979,1.823 0.917,0.198 10 false CANL*h 4.313,2.271 5.229,2.469 0.917,0.198 10 false CANL*d 4.448,1.271 5.365,1.469 0.917,0.198 10 false G189 4.563,0.865 5.479,1.063 0.917,0.198 10 false CANH*b 4.438,0.573 5.354,0.771 0.917,0.198 10 false CANH*c 4.302,0.313 5.219,0.51 0.917,0.198 10 false CANH*d 4.573,1.719 5.49,1.917 0.917,0.198 10 false CANL*b 4.365,1.948 5.281,2.146 0.917,0.198 10 false CANL*c 2.448,0.104 3.365,0.302 0.917,0.198 10 false CANH*e 2.094,1.844 3.01,2.042 0.917,0.198 10 false CANL*g 2.146,0.625 3.063,0.823 0.917,0.198 10 false CANH*g 2.417,2.094 3.333,2.292 0.917,0.198 10 false CANL*f 2.219,0.344 3.135,0.542 0.917,0.198 10 false CANH*f 2.031,1.021 2.948,1.219 0.917,0.198 10 false CANH*h
*a Rear view of wire harness connector
(to No. 7 CAN Junction Connector)
*b for Combination Meter Assembly
*c for Power Steering ECU Assembly *d for Radio and Display Receiver Assembly (w/ Audio and Visual System [for Radio and Display Type])
*e for Spiral with Sensor Cable Sub-assembly (Steering Angle Sensor) *f for 4WD ECU Assembly (for 4WD/AWD)
*g for No. 6 CAN Junction Connector *h for DLC3


No. 7 CAN Junction Connector Wiring Color Connect to

*1: w/ Audio and Visual System (for Radio and Display Type)

*2: for 4WD/AWD

G189-1 (CANH) G Combination meter assembly
G189-12 (CANL) W
G189-2 (CANH) LG Power steering ECU assembly
G189-13 (CANL) W
G189-3 (CANH) Y Radio and display receiver assembly*1
G189-14 (CANL) W
G189-4 (CANH) BE Spiral with sensor cable sub-assembly (steering angle sensor)
G189-15 (CANL) W
G189-6 (CANH) GR 4WD ECU assembly*2
G189-17 (CANL) W
G189-8 (CANH) V No. 6 CAN junction connector
G189-19 (CANL) W
G189-9 (CANH) BE DLC3
G189-20 (CANL) W



CHECK DLC3


a.
C253362C06
0.167,1 0.583,1.25 0.417,0.25 1.948,0.906 2.167,0.417 2.167,0.417 2.417,0.417 true 1.583,0.906 1.25,0.5 1.25,0.5 1,0.5 true 1.927,1.49 1.667,1.917 1.667,1.917 1.417,1.917 true 2.333,1.5 2.5,1.833 2.5,1.833 2.75,1.833 true 0.25,1.052 0.708,1.25 0.458,0.198 10 G14 0.75,0.417 1.208,0.615 0.458,0.198 10 CG 2.469,0.344 2.927,0.542 0.458,0.198 10 CANH 1.031,1.844 1.49,2.042 0.458,0.198 10 CANL 2.802,1.76 3.26,1.958 0.458,0.198 10 BAT 0.094,0.063 0.406,0.219 0.313,0.156 10 *a
*a Front view of DLC3


Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system.


NOTICE:
·

After turning the cable disconnected from negative (-) battery terminal, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION




b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G14-6 (CANH) - G14-14 (CANL) BE - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G14-6 (CANH) - G14-4 (CG) BE - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G14-14 (CANL) - G14-4 (CG) W - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G14-6 (CANH) - G14-16 (BAT) BE - L HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G14-14 (CANL) - G14-16 (BAT) W - L LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK ECM


a.

for 2AR-FE:

C228683E02
5.281,0.26 5.74,0.51 0.458,0.25 2.438,0.24 2.896,0.49 0.458,0.25 4.781,1.031 4.448,0.365 4.448,0.365 4.229,0.365 true 4.781,1.135 4.479,0.604 4.479,0.604 4.24,0.604 true 2.667,1.042 2.365,0.51 2.365,0.51 2.125,0.51 true 6.125,1.031 6.469,0.604 6.469,0.604 6.719,0.604 true 5.375,0.302 5.833,0.5 0.458,0.198 10 A62 2.552,0.292 3.01,0.49 0.458,0.198 10 B77 3.823,0.292 4.5,0.5 0.677,0.208 10 CANH 3.865,0.542 4.542,0.75 0.677,0.208 10 CANL 1.906,0.438 2.365,0.635 0.458,0.198 10 E1 6.76,0.521 7.156,0.677 0.396,0.156 10 BATT

i.

Disconnect the ECM connectors.

C229008C05
1.656,0.51 2.073,0.76 0.417,0.25 4.771,0.583 5.188,0.833 0.417,0.25 1.438,1.396 1,0.917 1,0.917 0.75,0.917 true 2.604,1.448 2.948,2.115 2.948,2.115 3.135,2.115 true 2.594,1.365 2.885,0.927 2.885,0.927 3.094,0.927 true 4.844,1.406 4.417,0.75 4.417,0.75 4.26,0.75 true 0.083,0.083 0.396,0.24 0.313,0.156 10 *a 0.344,0.844 0.75,1.083 0.406,0.24 10 BATT 3.135,0.844 3.635,1.094 0.5,0.25 10 CANH 1.729,0.552 2.135,0.792 0.406,0.24 10 A62 4.063,0.667 4.469,0.906 0.406,0.24 10 E1 4.833,0.625 5.24,0.865 0.406,0.24 10 B77 3.156,2.042 3.656,2.292 0.5,0.25 10 CANL
*a Front view of wire harness connector
(to ECM)
- -



ii.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A62-13 (CANH) - A62-26 (CANL) Y - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 108 to 132 Ω
A62-13 (CANH) - B77-16 (E1) Y - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
A62-26 (CANL) - B77-16 (E1) W - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
A62-13 (CANH) - A62-1 (BATT) Y - W HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A62-26 (CANL) - A62-1 (BATT) W - W LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



b.

for 3ZR-FAE, 3ZR-FE:

C228683C19
5.281,0.26 5.74,0.51 0.458,0.25 2.438,0.396 2.896,0.646 0.458,0.25 2.438,0.083 2.896,0.333 0.458,0.25 4.802,1.042 4.448,0.417 4.448,0.417 4.229,0.417 true 4.781,1.135 4.479,0.604 4.479,0.604 4.24,0.604 true 2.688,1.042 2.188,0.573 2.188,0.573 1.948,0.573 true 6.125,1.031 6.469,0.604 6.469,0.604 6.719,0.604 true 1.948,2.271 1.771,2.271 1.771,2.271 1.104,1.156 true 5.385,0.292 5.844,0.49 0.458,0.198 10 false A62 2.552,0.115 3.01,0.313 0.458,0.198 10 false B93 3.781,0.292 4.458,0.5 0.677,0.208 10 false CANH 3.854,0.521 4.531,0.729 0.677,0.208 10 false CANL 1.583,0.458 2.427,0.635 0.844,0.177 10 false E1*D 6.76,0.49 7.156,0.646 0.396,0.156 10 false BATT 2.01,2.156 3.708,2.354 1.698,0.198 10 false E1*A, *B, *C 2.542,0.406 3,0.604 0.458,0.198 10 false B75 2.938,0.417 3.396,0.615 0.458,0.198 10 false *D 2.948,0.115 3.625,0.417 0.677,0.302 10 false *A, *B, *C
*A for 3ZR-FAE *B for 3ZR-FE, Manual Transaxle System
*C for 3ZR-FE, CVT (K114) *D for 3ZR-FE, CVT (K111)
*a Front view of wire harness connector
(to ECM)
- -


i.

Disconnect the ECM connectors.

C229008C52
1.656,0.51 2.073,0.76 0.417,0.25 4.771,0.583 5.188,0.833 0.417,0.25 4.771,0.25 5.188,0.5 0.417,0.25 1.438,1.396 1,0.917 1,0.917 0.75,0.917 true 2.615,1.448 2.896,1.646 2.896,1.646 3.083,1.646 true 2.615,1.375 2.865,1.125 2.865,1.125 3.073,1.125 true 4.844,1.406 4.417,0.75 4.417,0.75 4.26,0.75 true 5.958,1.51 5.563,2.313 5.563,2.313 5.406,2.313 true 0.083,0.083 0.396,0.24 0.313,0.156 10 false *a 0.354,0.833 0.76,1.073 0.406,0.24 10 false BATT 3.115,1.031 3.688,1.281 0.573,0.25 10 false CANH 1.74,0.542 2.146,0.781 0.406,0.24 10 false A62 3.875,0.656 4.635,0.865 0.76,0.208 10 false E1*D 4.865,0.604 5.271,0.844 0.406,0.24 10 false B75 3.135,1.542 3.76,1.792 0.625,0.25 10 false CANL 4.542,2.208 5.781,2.417 1.24,0.208 10 false E1*A, *B, *C 5.26,0.604 5.667,0.844 0.406,0.24 10 false *D 4.854,0.271 5.26,0.51 0.406,0.24 10 false B93 5.26,0.281 6.01,0.542 0.75,0.26 10 false *A, *B, *C
*A for 3ZR-FAE *B for 3ZR-FE, Manual Transaxle System
*C for 3ZR-FE, CVT (K114) *D for 3ZR-FE, CVT (K111)
*a Front view of wire harness connector
(to ECM)
- -



ii.

Measure the resistance according to the value(s) in the table below.

for 3ZR-FAE
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A62-13 (CANH) - A62-26 (CANL) Y - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 108 to 132 Ω
A62-13 (CANH) - B93-59 (E1) Y - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
A62-26 (CANL) - B93-59 (E1) W - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
A62-13 (CANH) - A62-1 (BATT) Y - W HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A62-26 (CANL) - A62-1 (BATT) W - W LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

for 3ZR-FE, Manual Transaxle System
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A62-13 (CANH) - A62-26 (CANL) Y - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 108 to 132 Ω
A62-13 (CANH) - B93-59 (E1) Y - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
A62-26 (CANL) - B93-59 (E1) W - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
A62-13 (CANH) - A62-1 (BATT) Y - W HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A62-26 (CANL) - A62-1 (BATT) W - W LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

for 3ZR-FE, CVT (K114)
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A62-13 (CANH) - A62-26 (CANL) Y - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 108 to 132 Ω
A62-13 (CANH) - B93-59 (E1) Y - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
A62-26 (CANL) - B93-59 (E1) W - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
A62-13 (CANH) - A62-1 (BATT) Y - W HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A62-26 (CANL) - A62-1 (BATT) W - W LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

for 3ZR-FE, CVT (K111)
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A62-13 (CANH) - A62-26 (CANL) Y - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 108 to 132 Ω
A62-13 (CANH) - B75-16 (E1) Y - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
A62-26 (CANL) - B75-16 (E1) W - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
A62-13 (CANH) - A62-1 (BATT) Y - W HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A62-26 (CANL) - A62-1 (BATT) W - W LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



c.

for 2WW:

C228683C18
5.281,0.26 5.74,0.51 0.458,0.25 4.885,1.146 4.615,0.333 4.615,0.333 4.396,0.333 true 4.781,1.135 4.365,0.604 4.365,0.604 4.24,0.604 true 5.99,1.146 6.469,0.604 6.469,0.604 6.719,0.604 true 5.781,1.052 6.125,0.344 6.125,0.344 6.375,0.344 true 5.385,0.292 5.844,0.49 0.458,0.198 10 false A62 3.823,0.51 4.5,0.719 0.677,0.208 10 false CANH 3.99,0.24 4.667,0.448 0.677,0.208 10 false CANL 6.438,0.229 6.896,0.427 0.458,0.198 10 false E1 6.76,0.49 7.156,0.646 0.396,0.156 10 false BATT

i.
C300832C23
1.448,0.302 1.865,0.583 0.417,0.281 2.219,1.323 2.5,0.615 2.5,0.615 2.646,0.615 true 2.302,1.323 2.677,1.052 2.677,1.052 2.823,1.052 true 0.938,0.604 1.115,0.604 1.115,0.604 1.427,1.26 true 0.479,0.833 0.656,0.833 0.656,0.833 1.219,1.344 true 0.188,0.135 0.5,0.333 0.313,0.198 10 false *a 2.875,0.948 3.333,1.104 0.458,0.156 10 false CANH 2.688,0.531 3.156,0.688 0.469,0.156 10 false CANL 1.542,0.344 1.875,0.49 0.333,0.146 10 false A62 0.719,0.49 1.031,0.688 0.313,0.198 10 false E1 0.125,0.74 0.542,0.958 0.417,0.219 10 false BATT
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


ii.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A62-26 (CANH) - A62-25 (CANL) Y - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 108 to 132 Ω
A62-26 (CANH) - A62-4 (E1) Y - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
A62-25 (CANL) - A62-4 (E1) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
A62-26 (CANH) - A62-15 (BATT) Y - W HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A62-25 (CANL) - A62-15 (BATT) W - W LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



d.

for 2AD-FTV, 2AD-FHV, 2AD-CCo, 2AD-DPF:

C159489E30
2.344,0.385 2.76,0.656 0.417,0.271 4.781,0.458 5.198,0.729 0.417,0.271 5.094,1.073 5.563,0.469 5.563,0.469 5.729,0.469 true 5.781,1.188 6.229,1.438 6.229,1.438 6.417,1.438 true 5.24,1.073 5.75,0.667 5.75,0.667 5.917,0.667 true 1.219,1.99 1,2.156 1,2.156 0.74,2.156 true 4.885,0.49 5.354,0.688 0.469,0.198 10 false A61 2.438,0.438 2.906,0.635 0.469,0.198 10 false B76 5.958,0.552 6.656,0.75 0.698,0.198 10 false CANL 5.771,0.365 6.469,0.563 0.698,0.198 10 false CANH 6.479,1.365 7.021,1.563 0.542,0.198 10 false BATT 0.542,2.063 1.083,2.26 0.542,0.198 10 false E1

i.

Disconnect the ECM connectors.

C234869C12
0.323,1.354 0.792,1.625 0.469,0.271 4.542,0.51 5.01,0.781 0.469,0.271 1.458,0.833 1.677,0.833 1.677,0.833 1.958,1.188 true 2.917,0.823 2.781,0.823 2.781,0.823 2.438,1.208 true 6.125,2.188 5.823,2.188 5.823,2.188 5.667,1.813 true 2.75,0.531 2.615,0.531 2.615,0.531 2.344,1.208 true 0.448,1.396 0.74,1.573 0.292,0.177 10 false A61 0.125,0.073 0.417,0.25 0.292,0.177 10 false *a 1.104,0.74 1.531,0.906 0.427,0.167 10 false BATT 2.958,0.719 3.823,0.885 0.865,0.167 10 false CANH 6.177,2.073 7.042,2.24 0.865,0.167 10 false E1 4.656,0.531 4.99,0.708 0.333,0.177 10 false B76 2.802,0.417 3.667,0.583 0.865,0.167 10 false CANL
*a Front view of wire harness connector
(to ECM)
- -



ii.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A61-7 (CANH) - A61-6 (CANL) Y - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 108 to 132 Ω
A61-7 (CANH) - B76-109 (E1) Y - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
A61-6 (CANL) - B76-109 (E1) W - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
A61-7 (CANH) - A61-2 (BATT) Y - W HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A61-6 (CANL) - A61-2 (BATT) W - W LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY


C278790C08
2.51,5.542 2.927,5.792 0.417,0.25 3.333,7.385 3.75,7.635 0.417,0.25 1.302,3.656 1.719,3.906 0.417,0.25 3.875,5.792 4.167,6.25 4.167,6.25 4.333,6.25 true 3.167,6.198 3.417,6.198 3.417,6.198 3.781,5.781 true 3.49,8.188 3.833,8.583 3.833,8.583 4,8.583 true 3,8.583 3.167,8.583 3.167,8.583 3.396,8.177 true 1.25,4.844 1.5,4.844 false 1.25,7.042 1.5,7.042 false 2.417,3.417 2.583,3.417 2.583,3.417 3,3.781 true 5.333,3.417 5.167,3.417 5.167,3.417 4.771,3.771 true 0.25,4.26 0.917,4.417 0.667,0.156 10 false *A 0.25,6.604 0.563,6.76 0.313,0.156 10 false *B 2.708,6.115 3.354,6.354 0.646,0.24 10 false CANH 1.083,4.76 1.396,4.917 0.313,0.156 10 false *1 4.396,6.167 5.042,6.406 0.646,0.24 10 false CANL 2.583,5.583 2.896,5.74 0.313,0.156 10 false G78 3.417,7.427 3.729,7.583 0.313,0.156 10 false G78 4.063,8.51 4.708,8.75 0.646,0.24 10 false CANL 2.573,8.5 3.219,8.75 0.646,0.25 10 false CANH 1.073,6.969 1.385,7.125 0.313,0.156 10 false *1 1.469,3.698 2.135,3.854 0.667,0.156 10 false A 2,3.344 2.646,3.583 0.646,0.24 10 false GND1 5.417,3.344 6.063,3.583 0.646,0.24 10 false BECU 2.667,1.667 3.333,1.823 0.667,0.156 10 false A
*A Main Body ECU (Multiplex Network Body ECU) with 1 Connector *B Main Body ECU (Multiplex Network Body ECU) with 3 Connectors
*1 Main Body ECU (Multiplex Network Body ECU) - -


a.

Remove the main body ECU (multiplex network body ECU).

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL

C334662C01
1.458,0.104 1.958,0.385 0.5,0.281 5.354,0.458 5.854,0.74 0.5,0.281 2.271,1.604 2.115,1.604 2.115,1.604 1.635,0.969 true 2.427,1.375 2.271,1.375 2.271,1.375 1.677,0.969 true 6.385,0.719 6.5,0.719 6.5,0.719 6.646,1.021 true 4.844,0.74 4.958,0.74 4.958,0.74 5.281,1.021 true 0.135,0.083 0.448,0.24 0.313,0.156 10 false *a 4.271,0.094 4.583,0.25 0.313,0.156 10 false *b 1.573,0.167 2.031,0.365 0.458,0.198 10 false G78 5.573,0.51 6.031,0.708 0.458,0.198 10 false A 2.365,1.521 2.979,1.719 0.615,0.198 10 false CANH 2.51,1.292 3.125,1.49 0.615,0.198 10 false CANL 4.417,0.667 5.031,0.865 0.615,0.198 10 false GND1 5.958,0.656 6.573,0.854 0.615,0.198 10 false BECU
*a Rear view of wire harness connector
(to Main Body ECU [Multiplex Network Body ECU])
*b Front view of wire harness connector
(to Main Body ECU [Multiplex Network Body ECU])



b.

Reconnect the instrument panel junction block assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G78-14 (CANH) - G78-13 (CANL) G - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G78-14 (CANH) - A-11 (GND1) G - None HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G78-13 (CANL) - A-11 (GND1) W - None LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G78-14 (CANH) - A-30 (BECU) G - None HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G78-13 (CANL) - A-30 (BECU) W - None LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK COMBINATION METER ASSEMBLY


E161130E26
3.344,0.26 3.823,0.542 0.479,0.281 4.719,1.208 4.885,1.563 4.885,1.563 4.969,1.563 true 2.438,1.229 2.188,1.427 2.188,1.427 2.063,1.427 true 3.375,1.208 3.146,1.646 3.146,1.646 3.021,1.646 true 3.51,1.208 3.698,1.615 3.698,1.615 3.885,1.615 true 3.438,0.323 3.719,0.49 0.281,0.167 10 G16 5.01,1.479 5.271,1.667 0.26,0.188 10 ET 1.906,1.344 2.042,1.531 0.135,0.188 10 B 2.604,1.563 3.021,1.729 0.417,0.167 10 CANH 3.927,1.531 4.354,1.688 0.427,0.156 10 CANL

a.
C240157C07
1.531,0.146 1.969,0.458 0.438,0.313 1.719,1.219 2.26,1.76 2.26,1.76 2.49,1.76 true 1.635,1.219 1.375,1.844 1.375,1.844 1.135,1.844 true 0.979,1.219 0.781,1.083 0.781,1.083 0.604,1.083 true 2.865,1.448 2.708,1.448 2.708,1.448 2.563,1.229 true 0.073,0.083 0.385,0.24 0.313,0.156 10 *a 1.625,0.229 2.083,0.427 0.458,0.198 10 G16 0.719,1.75 1.177,1.948 0.458,0.198 10 CANH 2.531,1.667 3.01,1.865 0.479,0.198 10 CANL 2.917,1.385 3.219,1.656 0.302,0.271 10 ET 0.49,1.021 0.854,1.281 0.365,0.26 10 B
*a Rear view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G16-32 (CANH) - G16-31 (CANL) G - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 108 to 132 Ω
G16-32 (CANH) - G16-21 (ET) G - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G16-31 (CANL) - G16-21 (ET) W - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G16-32 (CANH) - G16-40 (B) G - Y HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G16-31 (CANL) - G16-40 (B) W - Y LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK AIRBAG SENSOR ASSEMBLY


C184818E01
3.177,0.417 3.573,0.677 0.396,0.26 3.656,1.333 3.917,0.729 3.917,0.729 4.135,0.729 true 3.781,1.594 4.021,2.052 4.021,2.052 4.24,2.052 true 2.865,2.115 3.073,2.115 3.073,2.115 3.417,1.594 true 3.24,0.448 3.698,0.646 0.458,0.198 10 G92 4.177,0.625 4.813,0.917 0.635,0.292 10 CANH 4.281,1.948 4.917,2.24 0.635,0.292 10 CANL 2.656,2.021 3.292,2.313 0.635,0.292 10 E1

a.
C227529C03
0.375,2.521 0.771,2.781 0.396,0.26 0.365,0.948 0.76,1.208 0.396,0.26 2.198,2.896 2.333,3.115 2.333,3.115 2.552,3.115 true 2.115,1.323 2.313,1.677 2.313,1.677 2.552,1.677 true 2.021,1.01 2.438,0.656 2.438,0.656 2.688,0.656 true 1.208,1.677 1.438,1.677 1.438,1.677 1.76,1.323 true 0.177,0.073 0.427,0.271 0.25,0.198 10 *a 0.198,2.083 0.51,2.24 0.313,0.156 10 *b 0.438,2.573 0.781,2.781 0.344,0.208 10 G14 0.417,1 0.76,1.208 0.344,0.208 10 G92 2.75,0.583 3.292,0.792 0.542,0.208 10 CANH 2.604,1.604 3.146,1.813 0.542,0.208 10 CANL 2.604,3.042 3.146,3.25 0.542,0.208 10 BAT 1,1.604 1.542,1.813 0.542,0.208 10 E1
*a Rear view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of DLC3


Disconnect the airbag sensor assembly connector.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G92-13 (CANH) - G92-22 (CANL) BR - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G92-13 (CANH) - G92-25 (E1) BR - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G92-22 (CANL) - G92-25 (E1) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G92-13 (CANH) - G14-16 (BAT) BR - L HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G92-22 (CANL) - G14-16 (BAT) W - L LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)


C306841E06
3.271,0.188 3.844,0.427 0.573,0.24 1.552,0.781 1.698,0.781 1.698,0.781 2.125,1.115 true 2.271,0.385 2.417,0.385 2.417,0.385 2.927,1.104 true 2.083,2.396 2.281,2.396 2.281,2.396 2.896,1.385 true 4.958,1.104 5.344,0.792 5.344,0.792 5.542,0.792 true 3.417,0.198 3.729,0.396 0.313,0.198 10 false A80 5.604,0.688 6.135,0.927 0.531,0.24 10 false GND1 1.896,0.281 2.427,0.521 0.531,0.24 10 false CANL 1.646,2.302 2.177,2.542 0.531,0.24 10 false CANH 1.302,0.656 1.833,0.896 0.531,0.24 10 false BM

a.
C321017C27
0.094,0.969 0.531,1.198 0.438,0.229 2.49,0.958 2.781,0.49 2.781,0.49 2.979,0.49 true 2.073,1.094 1.865,1.865 1.865,1.865 1.677,1.865 true 2.073,0.979 1.813,0.354 1.813,0.354 1.656,0.354 true 0.896,0.948 0.635,0.542 0.635,0.542 0.479,0.542 true 0.125,0.104 0.438,0.302 0.313,0.198 10 false *a 3.042,0.375 3.333,0.656 0.292,0.281 10 false BM 0.177,0.99 0.635,1.188 0.458,0.198 10 false A80 1.229,1.76 1.844,1.958 0.615,0.198 10 false CANH 1.229,0.25 1.844,0.448 0.615,0.198 10 false CANL 0.083,0.417 0.698,0.615 0.615,0.198 10 false GND1
*a Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU])


Disconnect the brake actuator assembly (skid control ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A80-22 (CANH) - A80-10 (CANL) B - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
A80-22 (CANH) - A80-1 (GND1) B - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
A80-10 (CANL) - A80-1 (GND1) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
A80-22 (CANH) - A80-13 (BM) B - B HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A80-10 (CANL) - A80-13 (BM) W - B LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY (STEERING ANGLE SENSOR)


C228050E03
1.458,0.365 1.885,0.646 0.427,0.281 1.906,1.354 2.188,1.719 2.188,1.719 2.5,1.719 true 1.74,1.354 1.563,1.844 1.563,1.844 1.281,1.844 true 2.125,1.313 2.458,0.99 2.458,0.99 2.771,0.99 true 1.323,1.333 1.021,1.031 1.021,1.031 0.74,1.031 true 1.531,0.427 1.854,0.615 0.323,0.188 10 G12 2.833,0.896 3.24,1.052 0.406,0.156 10 ESS 2.552,1.635 3.052,1.844 0.5,0.208 10 CANL 0.875,1.76 1.375,1.969 0.5,0.208 10 CANH 0.438,0.958 0.938,1.167 0.5,0.208 10 BAT

a.
C277459C04
1.521,0.188 1.938,0.438 0.417,0.25 1.094,1.844 1.344,1.844 1.344,1.844 1.521,1.396 true 2.563,0.875 2.333,0.875 2.333,0.875 2.115,1.24 true 2.24,1.844 1.99,1.844 1.99,1.844 1.75,1.396 true 0.771,0.906 1.021,0.906 1.021,0.906 1.344,1.219 true 0.083,0.052 0.396,0.208 0.313,0.156 10 false *a 2.625,0.781 3.104,0.938 0.479,0.156 10 false BAT 0.458,0.823 0.938,0.979 0.479,0.156 10 false ESS 1.594,0.219 2.073,0.375 0.479,0.156 10 false G12 2.302,1.75 2.781,1.906 0.479,0.156 10 false CANH 0.688,1.76 1.167,1.917 0.479,0.156 10 false CANL
*a Front view of wire harness connector
(to Spiral with Sensor Cable Sub-assembly [Steering Angle Sensor])


Disconnect the spiral with sensor cable sub-assembly (steering angle sensor) connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G12-3 (CANH) - G12-2 (CANL) BE - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G12-3 (CANH) - G12-1 (ESS) BE - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G12-2 (CANL) - G12-1 (ESS) W - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G12-3 (CANH) - G12-5 (BAT) BE - SB HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G12-2 (CANL) - G12-5 (BAT) W - SB LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY (w/ Audio and Visual System [for Radio and Display Type])


C297912E01
4.917,0.094 5.385,0.385 0.469,0.292 1.417,0.125 1.885,0.417 0.469,0.292 0.896,0.469 1.052,0.469 1.052,0.469 1.26,0.698 true 1.729,0.927 1.99,1.292 1.99,1.292 2.156,1.292 true 4.99,0.802 5.292,1.333 5.292,1.333 5.458,1.333 true 4.448,1.375 4.594,1.375 4.594,1.375 4.885,0.802 true 1.479,0.177 2.094,0.375 0.615,0.198 10 false G141 4.979,0.146 5.594,0.344 0.615,0.198 10 false G143 5.5,1.229 6.115,1.427 0.615,0.198 10 false CANH 4.042,1.26 4.656,1.458 0.615,0.198 10 false CANL 2.208,1.188 2.823,1.385 0.615,0.198 10 false GND1 0.594,0.365 1.208,0.563 0.615,0.198 10 false +B1

a.
C277477C07
1.469,0.26 1.906,0.5 0.438,0.24 1.51,1.844 1.948,2.083 0.438,0.24 2.115,1.49 1.865,1.49 1.865,1.49 1.677,1.156 true 2.625,0.708 2.375,0.708 2.375,0.708 2.177,0.865 true 2.542,3.146 2.292,3.146 2.292,3.146 2.021,2.656 true 1.906,2.656 1.677,3.146 1.677,3.146 1.417,3.146 true 2.156,1.406 2.698,1.635 0.542,0.229 10 false GND1 0.125,0.135 0.583,0.333 0.458,0.198 10 false *a 1.51,0.302 1.969,0.5 0.458,0.198 10 false G141 1.542,1.885 2,2.083 0.458,0.198 10 false G143 2.667,0.625 3.208,0.854 0.542,0.229 10 false +B1 2.594,3.063 3.135,3.292 0.542,0.229 10 false CANL 1,3.073 1.542,3.302 0.542,0.229 10 false CANH
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)


Disconnect the radio and display receiver assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G143-9 (CANH) - G143-10 (CANL) Y - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G143-9 (CANH) - G141-7 (GND1) Y - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G143-10 (CANL) - G141-7 (GND1) W - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G143-9 (CANH) - G141-4 (+B1) Y - SB HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G143-10 (CANL) - G141-4 (+B1) W - SB LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK 4WD ECU ASSEMBLY (for 4WD/AWD)


C270073E03
3.385,0.135 3.813,0.438 0.427,0.302 4.667,1.531 5.146,2.646 5.146,2.646 5.385,2.646 true 4.865,1.531 5.344,2.396 5.344,2.396 5.552,2.396 true 1.677,0.313 1.906,0.313 1.906,0.313 2.427,1.156 true 3.469,0.208 3.938,0.375 0.469,0.167 10 G86 5.594,2.323 6.063,2.49 0.469,0.167 10 CANL 5.438,2.563 5.906,2.729 0.469,0.167 10 CANH 1.344,0.25 1.813,0.417 0.469,0.167 10 GND

a.
C251150C05
0.417,2.51 0.823,2.792 0.406,0.281 0.438,0.927 0.844,1.208 0.406,0.281 2.208,2.833 2.417,3.021 2.417,3.021 2.594,3.021 true 2.229,1.094 2.438,1.281 2.438,1.281 2.615,1.281 true 2.167,1.094 2.333,1.563 2.333,1.563 2.51,1.563 true 0.875,0.688 1.094,0.688 1.094,0.688 1.229,0.948 true 0.083,0.094 0.396,0.25 0.313,0.156 10 *a 0.104,2.083 0.417,2.24 0.313,0.156 10 *b 0.479,2.563 0.854,2.771 0.375,0.208 10 G14 2.656,2.938 3.031,3.146 0.375,0.208 10 BAT 2.563,1.49 3.042,1.76 0.479,0.271 10 CANH 2.667,1.198 3.146,1.469 0.479,0.271 10 CANL 0.51,0.99 0.885,1.198 0.375,0.208 10 G86 0.552,0.635 1.031,0.906 0.479,0.271 10 GND
*a Rear view of wire harness connector
(to 4WD ECU Assembly)
*b Front view of DLC3


Disconnect the 4WD ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G86-6 (CANH) - G86-5 (CANL) GR - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G86-6 (CANH) - G86-4 (GND) GR - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G86-5 (CANL) - G86-4 (GND) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G86-6 (CANH) - G14-16 (BAT) GR - L HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G86-5 (CANL) - G14-16 (BAT) W - L LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK ENGINE STOP AND START ECU (w/ Stop and Start System)


C347359E02
1.469,0.542 1.948,0.781 0.479,0.24 4.969,0.531 5.448,0.771 0.479,0.24 0.615,2.125 0.76,2.125 0.76,2.125 1.26,1.594 true 2.677,2.125 2.51,2.125 2.51,2.125 2.24,1.573 true 6.302,2.083 6.135,2.083 6.135,2.083 5.865,1.531 true 5.115,2.125 5.26,2.125 5.26,2.125 5.771,1.531 true 1.594,0.552 2.052,0.75 0.458,0.198 10 false A86 5.063,0.563 5.521,0.76 0.458,0.198 10 false G87 2.719,2.01 3.177,2.208 0.458,0.198 10 false BIN1 0.188,2.01 0.646,2.208 0.458,0.198 10 false GND1 6.333,1.99 6.792,2.188 0.458,0.198 10 false CANH 4.708,2.021 5.167,2.219 0.458,0.198 10 false CANL

a.
C347360C02
0.146,2.427 0.563,2.635 0.417,0.208 0.365,0.781 0.781,0.99 0.417,0.208 0.677,1.5 0.833,1.5 0.833,1.5 1.125,1.177 true 0.49,3.052 0.646,3.052 0.646,3.052 0.938,2.729 true 0.802,3.26 0.958,3.26 0.958,3.26 1.042,2.708 true 2.656,1.583 2.469,1.583 2.469,1.583 2.24,1.219 true 0.125,0.146 0.438,0.302 0.313,0.156 10 false *a 0.438,0.792 0.75,0.948 0.313,0.156 10 false A86 0.229,2.438 0.542,2.594 0.313,0.156 10 false G87 0.333,1.396 0.792,1.604 0.458,0.208 10 false BIN1 2.708,1.479 3.167,1.688 0.458,0.208 10 false GND1 0.063,2.958 0.521,3.167 0.458,0.208 10 false CANH 0.396,3.167 0.854,3.375 0.458,0.208 10 false CANL
*a Front view of wire harness connector
(to Engine Stop and Start ECU)


Disconnect the engine stop and start ECU connectors.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G87-13 (CANH) - G87-14 (CANL) LG - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G87-13 (CANH) - A86-8 (GND1) LG - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G87-14 (CANL) - A86-8 (GND1) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G87-13 (CANH) - A86-3 (BIN1) LG - L HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G87-14 (CANL) - A86-3 (BIN1) W - L LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY


E219842E08
3.396,0.208 3.813,0.469 0.417,0.26 1.969,0.438 2.198,0.438 2.198,0.438 2.615,0.865 true 2.333,0.229 2.563,0.229 2.563,0.229 2.76,0.844 true 2.229,1.354 2.396,1.354 2.396,1.354 2.698,1.031 true 3.469,0.26 3.927,0.458 0.458,0.198 10 G80 1.896,0.146 2.375,0.344 0.479,0.198 10 CANH 1.573,0.354 2.052,0.552 0.479,0.198 10 CANL 1.896,1.271 2.375,1.469 0.479,0.198 10 GND

a.
C279367C02
1.479,0.167 1.906,0.406 0.427,0.24 0.385,2.563 0.813,2.802 0.427,0.24 2.594,3.073 2.396,3.073 2.396,3.073 2.208,2.813 true 1.094,1.021 0.896,0.76 0.896,0.76 0.708,0.76 true 1.177,1.01 0.969,0.49 0.969,0.49 0.781,0.49 true 1.135,1.135 0.927,1.5 0.927,1.5 0.74,1.5 true 0.073,0.052 0.385,0.208 0.313,0.156 10 *a 0.115,1.948 0.427,2.104 0.313,0.156 10 *b 0.458,2.594 0.854,2.813 0.396,0.219 10 G14 1.552,0.208 1.948,0.427 0.396,0.219 10 G80 2.656,2.99 3.052,3.208 0.396,0.219 10 BAT 0.396,1.406 0.792,1.625 0.396,0.219 10 GND 0.333,0.677 0.802,0.896 0.469,0.219 10 CANL 0.365,0.406 0.833,0.625 0.469,0.219 10 CANH
*a Rear view of wire harness connector
(to Air Conditioning Amplifier Assembly)
*b Front view of DLC3


Disconnect the air conditioning amplifier assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G80-8 (CANH) - G80-9 (CANL) B - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G80-8 (CANH) - G80-23 (GND) B - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G80-9 (CANL) - G80-23 (GND) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G80-8 (CANH) - G14-16 (BAT) B - L HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G80-9 (CANL) - G14-16 (BAT) W - L LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK POWER STEERING ECU ASSEMBLY


C239855E06
3.781,1.781 4.188,2.021 0.406,0.24 3.656,0.271 4.063,0.51 0.406,0.24 1.854,0.896 2.188,1.094 0.333,0.198 0.896,1.323 1.229,1.521 0.333,0.198 2.021,0.896 2.021,0.781 false 1.042,1.313 1.042,1.135 true 3.385,2.406 3.594,2.406 3.594,2.406 3.823,2.573 true 3.406,3.125 3.615,3.125 3.615,3.125 3.844,2.729 true 3.156,1.563 3.375,1.563 3.375,1.563 3.563,1.052 true 4.698,1.521 4.438,1.521 4.438,1.521 4.198,1.052 true 0.969,1.344 1.281,1.542 0.313,0.198 10 h1 1.938,0.917 2.25,1.115 0.313,0.198 10 h2 3.771,0.313 4.083,0.51 0.313,0.198 10 h2 3.917,1.833 4.229,2.031 0.313,0.198 10 h1 2.948,2.344 3.5,2.521 0.552,0.177 10 CANH 2.979,3.052 3.531,3.229 0.552,0.177 10 CANL 2.729,1.49 3.281,1.667 0.552,0.177 10 PGND 4.75,1.448 5.302,1.625 0.552,0.177 10 PIG

a.
C279366C01
0.354,2.479 0.719,2.74 0.365,0.26 0.458,0.969 0.823,1.229 0.365,0.26 1.969,0.938 2.25,0.74 2.25,0.74 2.469,0.74 true 1.969,1.25 2.208,1.521 2.208,1.521 2.427,1.521 true 2.156,2.615 2.438,2.417 2.438,2.417 2.656,2.417 true 0.844,2.271 1.094,2.271 1.094,2.271 1.323,2.542 true 0.094,0.073 0.406,0.229 0.313,0.156 10 *a 0.563,1.01 0.875,1.167 0.313,0.156 10 h1 0.469,2.531 0.781,2.688 0.313,0.156 10 h2 2.521,0.646 3.01,0.854 0.49,0.208 10 CANH 2.469,1.427 2.958,1.635 0.49,0.208 10 CANL 2.708,2.333 3.198,2.542 0.49,0.208 10 PGND 0.573,2.188 1.063,2.396 0.49,0.208 10 PIG
*a Front view of wire harness connector
(to Power Steering ECU Assembly)


Disconnect the power steering ECU assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
h1-4 (CANH) - h1-8 (CANL) W - B HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
h1-4 (CANH) - h2-2 (PGND) W - R HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
h1-8 (CANL) - h2-2 (PGND) B - R LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
h1-4 (CANH) - h2-1 (PIG) W - R HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
h1-8 (CANL) - h2-1 (PIG) B - R LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher