Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for RHD without Central Gateway ECU) › from 2015.10
RM3090E _57 Power Source / Network _008434 NETWORKING _0221949 CAN COMMUNICATION SYSTEM(for RHD without Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD without Central Gateway ECU)  Air Conditioning Amplifier Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Air Conditioning Amplifier Communication Stop Mode Either condition is met:
·

"Air Conditioning Amplifier" is not displayed on "CAN Bus Check".

(Click here)

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Air Conditioning Amplifier Communication Stop Mode" in "DTC Combination Table".

(Click here)


·

Power source or inside air conditioning amplifier assembly

·

Air conditioning amplifier assembly CAN branch wire or connector

·

Air conditioning amplifier assembly



WIRING DIAGRAM

C277463E07
5.26,3.917 6.833,4.25 1.573,0.333 10 false G80 5.26,4.083 6.833,4.417 1.573,0.333 10 false Air Conditioning Amplifier Assembly 5.667,3.292 6.833,3.458 1.167,0.167 10 false GND 5.667,2.458 6.833,2.625 1.167,0.167 10 false IG+ 5.656,0.958 6.823,1.125 1.167,0.167 10 false CANH 5.667,1.552 6.833,1.719 1.167,0.167 10 false CANL 5.417,1.417 6.583,1.583 1.167,0.167 10 false 9 5.417,0.844 6.583,1.01 1.167,0.167 10 false 8 5.438,2.333 6.604,2.5 1.167,0.167 10 false 1 5.396,3.156 6.563,3.323 1.167,0.167 10 false 23 1.688,0.875 2.854,1.042 1.167,0.167 10 false 2 1.708,1.438 2.875,1.604 1.167,0.167 10 false 13 0.323,1.896 1.49,2.063 1.167,0.167 10 false G188 0.333,2.083 2.833,2.25 2.5,0.167 10 false No. 6 CAN Junction Connector 1.719,2.427 4.219,2.615 2.5,0.188 10 false from IG1 NO.1 Relay 4.115,2.313 4.698,2.563 0.583,0.25 10 false HTR-IG

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD without Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

DTC check procedure: Turn the ignition switch to ON and wait at least 11.6 seconds.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD without Central Gateway ECU)>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (AIR CONDITIONING AMPLIFIER ASSEMBLY CAN BRANCH WIRE)
a.
C334663C01
1.406,0.552 1.917,0.906 0.51,0.354 1.156,1.667 1.01,0.844 1.01,0.844 0.875,0.844 true 1.042,1.656 0.635,1.188 0.635,1.188 0.5,1.188 true 0.115,0.146 0.427,0.302 0.313,0.156 10 false *a 1.542,0.646 2,0.844 0.458,0.198 10 false G80 0.427,0.76 1.042,0.958 0.615,0.198 10 false CANH 0.083,1.125 0.698,1.323 0.615,0.198 10 false CANL
*a Rear view of wire harness connector
(to Air Conditioning Amplifier Assembly)


Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the air conditioning amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G80-8 (CANH) - G80-9 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY CAN BRANCH WIRE OR CONNECTOR (CANH, CANL)

2.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - BATTERY AND BODY GROUND)
a.
C334663C02
1.406,0.552 1.917,0.906 0.51,0.354 2.458,1.646 2.656,1.031 2.656,1.031 2.833,1.031 true 1.094,1.802 0.646,2.531 0.646,2.531 0.51,2.531 true 0.115,0.146 0.427,0.302 0.313,0.156 10 false *a 1.542,0.646 2,0.844 0.458,0.198 10 false G80 2.917,0.958 3.292,1.24 0.375,0.281 10 false IG+ 0.135,2.458 0.75,2.656 0.615,0.198 10 false GND
*a Rear view of wire harness connector
(to Air Conditioning Amplifier Assembly)


Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G80-1 (IG+) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G80-23 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR