| Detection Item | Symptom | Trouble Area |
|---|---|---|
| Engine Stop and Start ECU Communication Stop Mode | Either condition is met:
|
·
Power source or inside engine stop and start ECU ·
Engine stop and start ECU CAN branch wire or connector ·
Engine stop and start ECU |
Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.
Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
Inspect the fuses for circuits related to this system before performing the following procedure.
DTC check procedure: Turn the ignition switch to ON and wait at least 60 seconds.
After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.
Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.
| *a | Rear view of wire harness connector
(to Engine Stop and Start ECU) |
Disconnect the cable from the negative (-) battery terminal.
Disconnect the engine stop and start ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G87-13 (CANH) - G87-14 (CANL) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the cable to the negative (-) battery terminal.
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
| *a | Front view of wire harness connector
(to Engine Stop and Start ECU) |
- | - |
Disconnect the engine stop and start ECU connectors.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A86-3 (BIN1) - Body ground | Always | 9.5 to 14 V |
| A86-1 (BIN2) - Body ground | Always | 9.5 to 14 V |
| A66-1 (+B) - Body ground | Ignition switch ON | 9.5 to 14 V |
| G87-21 (IG1) - Body ground | Ignition switch ON | 9.5 to 14 V |
| G87-18 (IG2) - Body ground | Ignition switch ON | 9.5 to 14 V |
| G87-19 (ACC) - Body ground | Ignition switch ACC | 9.5 to 14 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A66-6 (DGND) - Body ground | Always | Below 1 Ω |
| A86-8 (GND1) - Body ground | Always | Below 1 Ω |
| A86-2 (GND2) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG