Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio Receiver Type) › from 2015.10
RM3090E _56 Audio / Visual / Telematics _008775 AUDIO / VIDEO _0048747 AUDIO AND VISUAL SYSTEM(for Radio Receiver Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio Receiver Type)  Radio Broadcast cannot be Received or Poor Reception  


PROCEDURE

1.CHECK RADIO RECEIVER ASSEMBLY
a.

Check the radio automatic station search function by activating it.


Result:
Proceed to
Automatic station search function does not stop
Automatic station search function stops on a station



Automatic station search function does not stop

2.CHECK OPTIONAL COMPONENTS

Automatic station search function stops on a station

2.CHECK OPTIONAL COMPONENTS
a.

Check if any optional components that may decrease reception capacity, such as sunshade film or a telephone antenna, are installed.

NOTICE:

Do not remove optional components without the permission of the customer.



Result:
Proceed to
Optional components are not installed
Optional components are installed



Optional components are not installed

3.CHECK RADIO RECEIVER ASSEMBLY

Optional components are installed

REMOVE OPTIONAL COMPONENTS AND CHECK AGAIN (SEE NOTICE ABOVE)

3.CHECK RADIO RECEIVER ASSEMBLY
a.
E187251

Remove the antenna connector from the radio receiver assembly.


b.

Turn the ignition switch ACC with the radio receiver assembly connector connected.


c.

Turn the radio on and tune into AM mode.


d.

Place a screwdriver, thin wire or other metal object on the radio receiver assembly antenna jack and check that noise can be heard from the speakers.


Result:
Proceed to
Noise can be heard from the speakers
Noise cannot be heard from the speakers



Noise can be heard from the speakers

4.INSPECT RADIO RECEIVER ASSEMBLY

Noise cannot be heard from the speakers

REPLACE RADIO RECEIVER ASSEMBLY

4.INSPECT RADIO RECEIVER ASSEMBLY
a.

Disconnect the RA radio receiver assembly connector.


b.
E188455E31
1.552,1.104 1.146,1.479 true 0.844,1.51 1.24,1.677 0.396,0.167 10 ANT+

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
5 (ANT+) - Body ground Ignition switch ACC
Radio switch on and FM or AM selected
11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK ANTENNA CORD SUB-ASSEMBLY

NG

REPLACE RADIO RECEIVER ASSEMBLY

5.CHECK ANTENNA CORD SUB-ASSEMBLY
a.
E288797C02
0.521,2.271 0.958,2.521 0.438,0.25 2.063,2.51 2.375,2.208 2.375,2.208 2.583,2.208 true 1.583,2.833 1.135,2.979 1.135,2.979 0.885,2.979 true 0.229,0.073 0.542,0.229 0.313,0.156 10 false *a 0.271,1.542 0.583,1.698 0.313,0.156 10 false *b 0.635,2.323 0.948,2.479 0.313,0.156 10 false RA 2.646,2.115 3.125,2.302 0.479,0.188 10 false ANT+ 0.5,2.896 0.979,3.083 0.479,0.188 10 false MAIN
*a Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly)
*b Front view of wire harness connector
(to Radio Receiver Assembly)


Disconnect the antenna connector from the No. 2 antenna cord sub-assembly.


b.

Disconnect the antenna connector from the radio receiver assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 - RA-3 (MAIN) Always Below 1 Ω
3 - RA-5 (ANT+) Always Below 1 Ω
2 - Body ground Always 10 kΩ or higher
3 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK NO. 2 ANTENNA CORD SUB-ASSEMBLY

NG

6.CHECK NO. 2 ANTENNA CORD SUB-ASSEMBLY
a.
E288795C02
0.26,0.104 0.573,0.26 0.313,0.156 10 false *a 0.271,1.677 0.583,1.833 0.313,0.156 10 false *b
*a Front view of wire harness connector
(to No. 3 Antenna Cord Sub-assembly)
*b Front view of wire harness connector
(to Antenna Cord Sub-assembly)


Disconnect the antenna connector from the No. 3 antenna cord sub-assembly.


b.

Disconnect the antenna connector from the antenna cord sub-assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 Always Below 1 Ω
3 - 3 Always Below 1 Ω
1 - Body ground Always 10 kΩ or higher
3 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK NO. 3 ANTENNA CORD SUB-ASSEMBLY

NG

7.CHECK NO. 3 ANTENNA CORD SUB-ASSEMBLY
a.
E333809C01
0.104,0.052 0.417,0.208 0.313,0.156 10 false *a 0.156,1.656 0.469,1.813 0.313,0.156 10 false *b
*a Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly)
*b Front view of wire harness connector
(to No. 1 Amplifier Antenna Assembly)


Disconnect the antenna connector from the No. 2 antenna cord sub-assembly.


b.

Disconnect the antenna connector from the No. 1 amplifier antenna assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 Always Below 1 Ω
3 - 1 Always Below 1 Ω
1 - Body ground Always 10 kΩ or higher
3 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.CHECK NO. 1 AMPLIFIER ANTENNA ASSEMBLY

NG

8.CHECK NO. 1 AMPLIFIER ANTENNA ASSEMBLY
a.

Replace the No. 1 amplifier antenna assembly and check if radio broadcasts can be received normally.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AMPLIFIER ANTENNA>REMOVAL


Result:
Proceed to
Radio broadcasts can be received normally
Radio broadcasts cannot be received normally



Radio broadcasts can be received normally

END (NO. 1 AMPLIFIER ANTENNA ASSEMBLY IS DEFECTIVE)

Radio broadcasts cannot be received normally

REPLACE RADIO RECEIVER ASSEMBLY