Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio and Display Type) › from 2015.10
RM3090E _56 Audio / Visual / Telematics _008775 AUDIO / VIDEO _0048748 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  Radio Broadcast cannot be Received or Poor Reception  


WIRING DIAGRAM

E334245E11
2.292,1.156 2.448,1.354 0.156,0.198 10 false 2 2.281,1.448 2.625,1.646 0.344,0.198 10 false 1 2.917,1.188 3.26,1.385 0.344,0.198 10 false 1 3.615,1.188 3.958,1.385 0.344,0.198 10 false 1 4.146,1.198 4.302,1.396 0.156,0.198 10 false 2 4.854,1.188 5.01,1.385 0.156,0.198 10 false 2 5.417,1.219 5.573,1.417 0.156,0.198 10 false 3 2.927,1.469 3.271,1.667 0.344,0.198 10 false 3 3.604,1.49 3.948,1.688 0.344,0.198 10 false 3 4.156,1.479 4.5,1.677 0.344,0.198 10 false 3 4.854,1.469 5.198,1.667 0.344,0.198 10 false 3 5.417,1.469 5.76,1.667 0.344,0.198 10 false 5 5.99,1.219 6.51,1.417 0.521,0.198 10 false MAIN 5.979,1.625 6.5,1.823 0.521,0.198 10 false ANT+ 5.854,2.854 6.375,3.052 0.521,0.198 10 false RA 5.854,3.021 7.031,3.583 1.177,0.563 10 false Radio and Display Receiver Assembly 4.76,2.281 5.656,2.635 0.896,0.354 10 false Antenna Cord Sub-assembly 3.396,2.292 4.635,2.635 1.24,0.344 10 false No. 2 Antenna Cord Sub-assembly 2.042,2.292 3.281,2.635 1.24,0.344 10 false No. 3 Antenna Cord Sub-assembly 0.094,1.979 1.573,2.542 1.479,0.563 10 false No. 1 Amplifier Antenna Assembly

PROCEDURE

1.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY
a.

Check the radio automatic station search function by activating it.

OK:

Automatic station search function stops on a station.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK OPTIONAL COMPONENTS
2.CHECK OPTIONAL COMPONENTS
a.

Check if any optional components that may decrease reception capacity, such as sunshade film or a telephone antenna, are installed.

OK:

Optional components are not installed.


NOTICE:

Do not remove optional components without the permission of the customer.



Result:
Proceed to
OK
NG



OK

3.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REMOVE OPTIONAL COMPONENTS AND CHECK AGAIN (SEE NOTICE ABOVE)

3.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY
a.
E276819

Remove the antenna connector from the radio and display receiver assembly.


b.

Turn the ignition switch to ACC with the radio and display receiver assembly connector connected.


c.

Turn the radio on and tune into AM mode.


d.

Place a screwdriver, thin wire or other metal object on the radio and display receiver assembly antenna jack and check that noise can be heard from the speakers.

OK:

Noise can be heard from the speakers.



Result:
Proceed to
OK
NG



OK

4.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

4.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
a.

Disconnect the RA radio and display receiver assembly connector.


b.
E188455E31
1.552,1.104 1.146,1.479 true 0.844,1.51 1.24,1.677 0.396,0.167 10 ANT+

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
5 (ANT+) - Body ground Ignition switch ACC
Radio switch on and FM or AM selected
11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK ANTENNA CORD SUB-ASSEMBLY

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

5.CHECK ANTENNA CORD SUB-ASSEMBLY
a.
E288614C03
0.531,0.771 0.99,0.99 0.458,0.219 0.969,1.583 1.219,1.583 1.219,1.583 1.469,1.25 true 2.354,0.708 2.104,0.708 2.104,0.708 1.938,0.958 true 0.073,0.073 0.385,0.271 0.313,0.198 10 false *a 0.104,1.823 0.417,2.021 0.313,0.198 10 false *b 0.667,0.802 0.979,1 0.313,0.198 10 false RA 0.604,1.5 1.115,1.677 0.51,0.177 10 false MAIN 2.385,0.615 2.896,0.792 0.51,0.177 10 false ANT+
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)
*b Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly)


Disconnect the radio and display receiver assembly connector.


b.

Remove the antenna connector from the No. 2 antenna cord sub-assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
RA-3 (MAIN) - 2 Always Below 1 Ω
RA-5 (ANT+) - 3 Always Below 1 Ω
RA-3 (MAIN) - Body ground Always 10 kΩ or higher
RA-5 (ANT+) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK NO. 2 ANTENNA CORD SUB-ASSEMBLY

NG

6.CHECK NO. 2 ANTENNA CORD SUB-ASSEMBLY
a.
E288795C02
0.26,0.104 0.573,0.26 0.313,0.156 10 false *a 0.271,1.677 0.583,1.833 0.313,0.156 10 false *b
*a Front view of wire harness connector
(to Antenna Cord Sub-assembly)
*b Front view of wire harness connector
(to No. 3 Antenna Cord Sub-assembly)


Remove the antenna connector from the antenna cord sub-assembly.


b.

Remove the antenna connector from the No. 3 antenna cord sub-assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 - 1 Always Below 1 Ω
3 - 3 Always Below 1 Ω
2 - Body ground Always 10 kΩ or higher
3 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK NO. 3 ANTENNA CORD SUB-ASSEMBLY

NG

7.CHECK NO. 3 ANTENNA CORD SUB-ASSEMBLY
a.
E335190C01
0.146,0.198 0.344,0.396 0.198,0.198 10 false *a 0.188,2.052 0.385,2.25 0.198,0.198 10 false *b 0.458,0.781 0.677,0.979 0.219,0.198 10 false *A 1.854,0.771 2.083,0.948 0.229,0.177 10 false *B
*A Except models with the vehicle identification number on the certification label ending with the character X.
*B Only for models with the vehicle identification number on the certification label ending with the character X.
*a Front view of wire harness connector
(to No. 1 Amplifier Antenna Assembly)
*b Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly)


Disconnect the antenna connector from the No. 1 amplifier antenna assembly.


b.

Disconnect the antenna connector from the No. 2 antenna cord sub-assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 - 1 Always Below 1 Ω
1 - 3 Always Below 1 Ω
2 - Body ground Always 10 kΩ or higher
1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.CHECK NO. 1 AMPLIFIER ANTENNA ASSEMBLY

NG

8.CHECK NO. 1 AMPLIFIER ANTENNA ASSEMBLY
a.

Replace the No. 1 amplifier antenna assembly and check if radio broadcasts can be received normally.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AMPLIFIER ANTENNA>REMOVAL

OK:

Radio broadcasts can be received normally.



Result:
Proceed to
OK
NG



OK

END (NO. 1 AMPLIFIER ANTENNA ASSEMBLY IS DEFECTIVE)

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY