Home › Vehicle Exterior › SLIDING ROOF / CONVERTIBLE › SLIDING ROOF SYSTEM › from 2015.10
RM3090E _59 Vehicle Exterior _008793 SLIDING ROOF / CONVERTIBLE _0049191 SLIDING ROOF SYSTEM C

SLIDING ROOF / CONVERTIBLE  SLIDING ROOF SYSTEM  B2341  Sensor (Motor) Failure  B2344  Position Failure  


DESCRIPTION

When the sliding roof drive gear sub-assembly (sliding roof ECU) detects a motor malfunction and the sliding roof operation is stopped, DTC B2341 is stored.

When the sliding roof drive gear sub-assembly (sliding roof ECU) detects a gear position malfunction and the sliding roof operation is stopped, DTC B2344 is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2341 Sensor (Motor) Failure Sensor (motor) failure (When the sliding roof ECU enters fail-safe mode due to a problem with the motor)
·

Sliding roof drive gear sub-assembly (Sliding roof ECU)

·

Map light assembly (Sliding roof control switch)

·

Harness or connector


B2344 Position Failure Position failure (When the sliding roof ECU enters fail-safe mode due to a problem with the gear position)
·

Sliding roof drive gear sub-assembly (Sliding roof ECU)

·

Map light assembly (Sliding roof control switch)

·

Harness or connector



WIRING DIAGRAM

B271000E16
4.615,4.896 4.938,5.073 0.323,0.177 10 false Q8 2.458,4.219 2.958,4.375 0.5,0.156 10 false Q16 5.052,2.802 5.427,3.021 0.375,0.219 10 false OPN 5.052,3.042 5.396,3.24 0.344,0.198 10 false CLS 5.052,3.802 5.333,3.979 0.281,0.177 10 false UP 5.052,3.552 5.583,3.729 0.531,0.177 10 false DWN 4.896,2.698 5.031,2.875 0.135,0.177 10 false 7 4.896,2.958 5.031,3.135 0.135,0.177 10 false 5 4.896,3.458 5.031,3.635 0.135,0.177 10 false 6 4.896,3.708 5,3.885 0.104,0.177 10 false 4 3.75,2.698 4.094,2.875 0.344,0.177 10 false OPN 3.792,2.958 4.115,3.198 0.323,0.24 10 false CLS 3.615,3.458 4.104,3.667 0.49,0.208 10 false DOWN 3.875,3.708 4.115,3.906 0.24,0.198 10 false UP 4.156,2.698 4.26,2.875 0.104,0.177 10 false 7 4.156,2.958 4.26,3.135 0.104,0.177 10 false 8 4.156,3.708 4.417,3.896 0.26,0.188 10 false 16 4.156,3.458 4.396,3.635 0.24,0.177 10 false 17 2.427,2.823 2.833,3.021 0.406,0.198 10 false GND 2.156,2.823 2.427,3 0.271,0.177 10 false 20 5.813,4.094 5.938,4.271 0.125,0.177 10 false E 5.979,4 6.188,4.177 0.208,0.177 10 false 12 2.563,0.99 4.729,1.385 2.167,0.396 10 false Main Body ECU (Multiplex Network Body ECU) 0.875,0.979 2.104,1.333 1.229,0.354 10 false Combination Meter Assembly 3.667,0.521 4,0.688 0.333,0.167 10 false LIN2 2.99,0.521 3.354,0.688 0.365,0.167 10 false CAN 1.656,0.521 2.021,0.688 0.365,0.167 10 false CAN 5.063,0.521 5.479,0.688 0.417,0.167 10 false MPX1 0.688,5.448 2.333,5.635 1.646,0.188 10 false : LIN Communication Line 0.688,5.115 2.427,5.302 1.74,0.188 10 false : CAN Communication Line 2.458,4.396 4.24,4.771 1.781,0.375 10 false Map Light Assembly (Sliding Roof Control Switch) 4.615,5.073 6.979,5.479 2.365,0.406 10 false Sliding Roof Drive Gear Sub-assembly (Sliding Roof ECU)

CAUTION / NOTICE / HINT

NOTICE:
·

When the sliding roof drive gear sub-assembly (sliding roof ECU) is removed and reinstalled or replaced, it requires initialization.

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>INITIALIZATION

·

The sliding roof system uses the CAN and LIN communication systems. First, confirm that there are no malfunctions in the CAN and LIN communication systems. Refer to the How to Proceed with Troubleshooting procedure.

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.CHECK SLIDING ROOF OPERATION
a.

Check the sliding roof auto operation.

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>OPERATION CHECK

OK:

Auto operation operates normally.



Result:
Proceed to
OK
NG



OK

2.CHECK DTC OUTPUT

NG

3.INITIALIZE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU)
2.CHECK DTC OUTPUT
a.

Clear the DTCs.

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>DTC CHECK / CLEAR

Body Electrical > Sliding Roof > Clear DTCs
50002 147

b.

Check for DTCs.

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>DTC CHECK / CLEAR

Body Electrical > Sliding Roof > Trouble Codes
50001 147
OK:

DTC B2341 or B2344 is not output.



Result:
Proceed to
OK
NG



OK

NG

REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU)

3.INITIALIZE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU)
a.

Check that the sliding roof drive gear sub-assembly (sliding roof ECU) can be initialized.

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>INITIALIZATION

OK:

Sliding roof drive gear sub-assembly (sliding roof ECU) can be initialized.



Result:
Proceed to
OK
NG



OK

4.CHECK DTC OUTPUT

NG

5.CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU - SLIDING ROOF CONTROL SWITCH AND BODY GROUND)
4.CHECK DTC OUTPUT
a.

Clear the DTCs.

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>DTC CHECK / CLEAR

Body Electrical > Sliding Roof > Clear DTCs
50002 147

b.

Check for DTCs.

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>DTC CHECK / CLEAR

Body Electrical > Sliding Roof > Trouble Codes
50001 147
OK:

DTC B2341 or B2344 is not output.



Result:
Proceed to
OK
NG



OK

END (PROBLEM DUE TO INITIALIZATION FAILURE)

NG

REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU)

5.CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU - SLIDING ROOF CONTROL SWITCH AND BODY GROUND)
a.

Disconnect the Q16 map light assembly (sliding roof control switch) connector.


b.

Disconnect the Q8 sliding roof drive gear sub-assembly (sliding roof ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Q8-5 (CLS) - Q16-8 (CLS) Always Below 1 Ω
Q8-5 (CLS) - Body ground Always 10 kΩ or higher
Q8-7 (OPN) - Q16-7 (OPN) Always Below 1 Ω
Q8-7 (OPN) - Body ground Always 10 kΩ or higher
Q8-6 (DWN) - Q16-17 (DOWN) Always Below 1 Ω
Q8-6 (DWN) - Body ground Always 10 kΩ or higher
Q8-4 (UP) - Q16-16 (UP) Always Below 1 Ω
Q8-4 (UP) - Body ground Always 10 kΩ or higher
Q16-20 (GND) - Body ground Always Below 1 Ω
Q8-12 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.INSPECT MAP LIGHT ASSEMBLY (SLIDING ROOF CONTROL SWITCH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT MAP LIGHT ASSEMBLY (SLIDING ROOF CONTROL SWITCH)
a.

Remove the map light assembly (sliding roof control switch).

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Inspect the map light assembly (sliding roof control switch).

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SWITCH ASSEMBLY>INSPECTION


Result:
Proceed to
OK
NG



OK

REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU)

NG

REPLACE MAP LIGHT ASSEMBLY (SLIDING ROOF CONTROL SWITCH)