The sliding roof drive gear sub-assembly (sliding roof ECU) receives slide and tilt signals when the sliding roof control switch is operated and drives its built-in motor.
Inspect the fuses for circuits related to this system before performing the following procedure.
When the sliding roof drive gear sub-assembly (sliding roof ECU) is removed and reinstalled or replaced, it requires initialization.
Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>INITIALIZATION
The sliding roof system uses the LIN communication system. First, confirm that there are no malfunctions in the LIN communication system. Refer to the How to Proceed with Troubleshooting procedure.
Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Click here
When a sliding roof drive gear sub-assembly (sliding roof ECU) DTC is output, first perform troubleshooting for the sliding roof drive gear sub-assembly (sliding roof ECU) DTC.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Sliding Roof / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Open Switch | OPEN switch signal | ON or OFF | ON: OPEN switch pressed
OFF: OPEN switch not pressed |
- |
| Close Switch | CLOSE switch signal | ON or OFF | ON: CLOSE switch pressed
OFF: CLOSE switch not pressed |
- |
| Up Switch | UP switch signal | ON or OFF | ON: UP switch pressed
OFF: UP switch not pressed |
- |
| Down Switch | DOWN switch signal | ON or OFF | ON: DOWN switch pressed
OFF: DOWN switch not pressed |
- |
| Tester Display |
|---|
| Open Switch |
| Close Switch |
| Up Switch |
| Down Switch |
The GTS display changes according to switch operation as shown in the table.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Sliding Roof Drive Gear Sub-assembly [Sliding Roof ECU]) |
Disconnect the sliding roof drive gear sub-assembly (sliding roof ECU) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Q8-8 (B) - Body ground | Always | 11 to 14 V |
| Q8-1 (IG) - Body ground | Ignition switch ON | 11 to 14 V |
| Q8-1 (IG) - Body ground | Ignition switch off | Below 1 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Q8-12 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the map light assembly (sliding roof control switch).
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
Inspect the map light assembly (sliding roof control switch).
Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SWITCH ASSEMBLY>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the Q7 map light assembly (sliding roof control switch) connector.
Disconnect the Q16 sliding roof drive gear sub-assembly (sliding roof ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Q8-5 (CLS) - Q16-8 (CLS) | Always | Below 1 Ω |
| Q8-5 (CLS) - Body ground | Always | 10 kΩ or higher |
| Q8-7 (OPN) - Q16-7 (OPN) | Always | Below 1 Ω |
| Q8-7 (OPN) - Body ground | Always | 10 kΩ or higher |
| Q8-6 (DWN) - Q16-17 (DOWN) | Always | Below 1 Ω |
| Q8-6 (DWN) - Body ground | Always | 10 kΩ or higher |
| Q8-4 (UP) - Q16-16 (UP) | Always | Below 1 Ω |
| Q8-4 (UP) - Body ground | Always | 10 kΩ or higher |
| Q16-20 (GND) - Body ground | Always | Below 1 Ω |
| Q8-12 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG