Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › WHEEL OPENING MOULDING › from 2015.10
RM3090E _59 Vehicle Exterior _008798 EXTERIOR PANELS / TRIM _0050282 WHEEL OPENING MOULDING A

EXTERIOR PANELS / TRIM  WHEEL OPENING MOULDING  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 75656C 1.INSTALL CENTER QUARTER OUTSIDE MOULDING LH

HINT:

When installing the center quarter outside moulding LH, heat the vehicle body and center quarter outside moulding LH using a heat light.


Standard:
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)
Center Quarter Outside Moulding LH 20 to 30°C (68 to 86°F)


NOTICE:

Do not heat the vehicle body or center quarter outside moulding LH excessively.


a.

Clean the vehicle body surface.

i.

Using a heat light, heat the vehicle body surface.


ii.

Remove the double-sided tape from the vehicle body surface.


iii.

Wipe off any tape adhesive residue with cleaner.



b.
B422088C02
2.542,0.438 2.708,0.167 2.708,0.167 2.979,0.167 true 3.031,0.094 3.344,0.292 0.313,0.198 10 true *a
*a Double-sided Tape
V100155

Protective Tape


Install a new center quarter outside moulding LH.

i.

Remove the peeling paper from the face of the center quarter outside moulding LH.

HINT:

After removing the peeling paper, keep the exposed adhesive free from foreign matter.



ii.

Attach the 9 clips to install the center quarter outside moulding LH.

HINT:

Press the center quarter outside moulding LH firmly to install it.



iii.

Install the 2 clips and grommet.



Hide 65632D 2.INSTALL REAR WHEEL HOUSE FRONT PLATE LH

a.

Install the screw.


b.

Attach the clip to install the rear wheel house front plate LH.


Hide 75612D 3.INSTALL FRONT FENDER FRONT OUTSIDE MOULDING LH

HINT:

When installing the front fender front outside moulding LH, heat the vehicle body and front fender front outside moulding LH using a heat light.


Standard:
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)
Front Fender Front Outside Moulding LH 20 to 30°C (68 to 86°F)


NOTICE:

Do not heat the vehicle body or front fender front outside moulding LH excessively.


a.

Clean the vehicle body surface.

i.

Using a heat light, heat the vehicle body surface.


ii.

Remove the double-sided tape from the vehicle body surface.


iii.

Wipe off any tape adhesive residue with cleaner.



b.
B432920C01
2.177,0.417 2.458,0.177 2.458,0.177 2.729,0.177 true 2.333,2.021 2.167,1.719 2.167,1.719 1.865,1.719 true 1.104,1.188 1.104,0.938 true 2.771,0.094 3.083,0.292 0.313,0.198 10 true *a 1.01,1.188 1.323,1.385 0.313,0.198 10 true *b 1.646,1.625 1.844,1.854 0.198,0.229 10 true *c
*a Double-sided Tape
*b Clip A
*c Clip B
V100155

Protective Tape


Install the front fender front outside moulding LH.

i.

Remove the peeling paper from the face of the front fender front outside moulding LH.

HINT:

After removing the peeling paper, keep the exposed adhesive free from foreign matter.



ii.

Attach the 8 clips to install the front fender front outside moulding LH.

HINT:

Press the front fender front outside moulding LH firmly to install it.



iii.

Install the 5 grommets.


iv.

Install the clip labeled A and clip labeled B.



Hide 76622D 4.INSTALL FRONT FENDER MUDGUARD LH (w/ Mudguard)

a.

Install the front fender mudguard LH with the 3 screws.


b.

Install the clip.


Hide 52159 5.INSTALL REAR BUMPER COVER

Hide 52119A 6.INSTALL FRONT BUMPER COVER