Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM(w/ Entry and Start System) › from 2015.10
RM3090E _58 Vehicle Interior _008690 THEFT DETERRENT / KEYLESS ENTRY _0048164 IMMOBILISER SYSTEM(w/ Entry and Start System) Y

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(w/ Entry and Start System)  HOW TO PROCEED WITH TROUBLESHOOTING  


CAUTION / NOTICE / HINT

HINT:
·

Use this procedure to troubleshoot the immobiliser system.

·

*: Use the GTS.



PROCEDURE

1.VEHICLE BROUGHT TO WORKSHOP
Result:
Proceed to
NEXT



NEXT

2.INSPECT BATTERY VOLTAGE
2.INSPECT BATTERY VOLTAGE
a.

Measure the battery voltage.

Standard voltage:

11 to 14 V


If the voltage is below 11 V, recharge or replace the battery before proceeding to the next step.

HINT:

A simple method to determine whether the battery is discharged is to operate the horn.



Result:
Proceed to
NEXT



NEXT

3.TURN ENGINE SWITCH ON (IG)
3.TURN ENGINE SWITCH ON (IG)
HINT:

When using the GTS with the engine switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.


Result:
Proceed to
NEXT



NEXT

4.CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*
4.CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*

Result:
Proceed to
CAN DTC is not output
CAN DTC is output (for LHD)
CAN DTC is output (for RHD)



CAN DTC is not output

5.CHECK COMMUNICATION FUNCTION OF LIN COMMUNICATION SYSTEM*

CAN DTC is output (for LHD)

CAN DTC is output (for RHD)

5.CHECK COMMUNICATION FUNCTION OF LIN COMMUNICATION SYSTEM*
a.

Use the GTS to check if the LIN communication system is functioning normally.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR


Result:
Proceed to
LIN DTC is not output
LIN DTC is output



LIN DTC is not output

6.CHECK FOR DTC*

LIN DTC is output

6.CHECK FOR DTC*
a.

Check for DTCs and make a note of any codes that are output.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/ Entry and Start System)>DTC CHECK / CLEAR

Powertrain > Engine > Trouble Codes
50001 61
Powertrain > Engine and ECT > Trouble Codes
50001 234
Body Electrical > Telematics > Trouble Codes
50001 233
Chassis > EMPS > Trouble Codes
50001 142
Body Electrical > Entry&Start > Trouble Codes
50001 125

b.

Based on the DTCs output above, proceed to each diagnostic procedure.


Result:
Result Proceed to
DTC is not output A
SFI system DTC is output (for 2AR-FE [w/ Canister Pump Module]) B
SFI system DTC is output (for 2AR-FE [w/o Canister Pump Module]) C
SFI system DTC is output (for 3ZR-FAE) D
SFI system DTC is output (for 3ZR-FE [for K111, K111F]) E
SFI system DTC is output (for 3ZR-FE [except K111, K111F]) F
ECD system DTC is output (for 2WW) G
ECD system DTC is output (for 2AD-FTV [for CCo]) H
ECD system DTC is output (for 2AD-FTV [for DPF]) I
ECD system DTC is output (for 2AD-FHV) J
Steering lock system DTC is output K
Immobiliser system DTC is output L



A

7.PERFORM SYMPTOMS TABLE

B

C

D

E

F

G

H

I

J

K

L

7.PERFORM SYMPTOMS TABLE

Result:
Proceed to
Fault is not listed in problem symptoms table
Fault is listed in problem symptoms table



Fault is not listed in problem symptoms table

8.OVERALL ANALYSIS AND TROUBLESHOOTING*

Fault is listed in problem symptoms table

ADJUST, REPAIR OR REPLACE IN ACCORDANCE WITH PROBLEM SYMPTOMS TABLE

8.OVERALL ANALYSIS AND TROUBLESHOOTING*

NEXT

9.REPAIR OR REPLACE
9.REPAIR OR REPLACE
Result:
Proceed to
NEXT



NEXT

10.CHECK FOR DTC*
10.CHECK FOR DTC*
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/ Entry and Start System)>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Clear DTCs
50002 125

b.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/ Entry and Start System)>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Trouble Codes
50001 125
HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" of each diagnostic procedure.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/ Entry and Start System)>DIAGNOSTIC TROUBLE CODE CHART



Result:
Proceed to
DTC is not output
Immobiliser system DTC is output



DTC is not output

END

Immobiliser system DTC is output