Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM › from 2015.10
RM3090E _58 Vehicle Interior _008690 THEFT DETERRENT / KEYLESS ENTRY _0048165 THEFT DETERRENT SYSTEM C

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  B2762  Intrusion Sensor Signal Circuit Malfunction  


DESCRIPTION

The intrusion sensor (theft warning ultrasonic sensor) conducts self-diagnosis immediately after power is supplied to the sensor (when the theft deterrent system is set).

If a malfunction is detected in the ISIF line, the main body ECU (multiplex network body ECU) stores this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2762 Intrusion Sensor Signal Circuit Malfunction
After normal/trouble signal is output from intrusion sensor (theft warning ultrasonic sensor) as result of self-diagnosis, following malfunctions are detected:
1.

ISIF line circuit is open

2.

Reception of signals other than normal/trouble signal


·

Map light assembly

·

Intrusion sensor (theft warning ultrasonic sensor)

·

Main body ECU (multiplex network body ECU)

·

Harness or connector



WIRING DIAGRAM

B300521E15
5.646,2.135 6.229,2.354 0.583,0.219 10 false SSW1 5.646,1.698 5.958,1.927 0.313,0.229 10 false ISIF 5.365,3.052 7.063,3.448 1.698,0.396 10 false Main Body ECU (Multiplex Network Body ECU) 5.365,2.875 6.063,3.229 0.698,0.354 10 false G79 3.479,1.698 3.833,1.865 0.354,0.167 10 false IOUT 2.063,2.719 2.99,3.042 0.927,0.323 10 false Q16 3.427,2.125 3.906,2.333 0.479,0.208 10 false SOFF 2.063,2.875 3.688,3.083 1.625,0.208 10 false Map Light Assembly 1.375,1.771 1.844,2 0.469,0.229 10 false GND 1.156,1.625 1.385,1.906 0.229,0.281 10 false 20 1.74,0.281 2.948,0.542 1.208,0.26 10 false from Battery 2.01,1.354 3.167,1.875 1.156,0.521 10 false Intrusion Sensor (Theft Warning Ultrasonic Sensor) 5.396,2.01 5.802,2.354 0.406,0.344 10 false 8 5.385,1.563 5.927,1.896 0.542,0.333 10 false 12 3.906,1.573 4.219,1.802 0.313,0.229 10 false 14 3.552,1.25 3.865,1.438 0.313,0.188 10 false +B2 3.896,1.146 4.156,1.354 0.26,0.208 10 false 13 3.906,1.99 4.24,2.188 0.333,0.198 10 false 15 3.49,0.438 4.469,0.646 0.979,0.208 10 false ECU-B NO. 2

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

When replacing the main body ECU (multiplex network body ECU), make sure to replace it with a new one.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MAP LIGHT ASSEMBLY - BATTERY AND BODY GROUND)
a.
B432112C02
1.448,0.135 1.906,0.427 0.458,0.292 1.281,1.375 1.073,1.792 1.073,1.792 0.833,1.792 true 2.5,1.406 2.573,1.823 2.573,1.823 2.74,1.823 true 1.542,0.188 2,0.385 0.458,0.198 10 false Q16 0.531,1.698 0.99,1.896 0.458,0.198 10 false +B2 2.802,1.719 3.26,1.917 0.458,0.198 10 false GND
*a Front view of wire harness connector
(to Map Light Assembly)


Disconnect the map light assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Q16-13 (+B2) - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Q16-20 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK WAVEFORM (INTRUSION SENSOR [THEFT WARNING ULTRASONIC SENSOR]) (IOUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK WAVEFORM (INTRUSION SENSOR [THEFT WARNING ULTRASONIC SENSOR]) (IOUT)
a.

Using an oscilloscope, check the waveform.

B432111C02
2.292,0.271 2.708,0.521 0.417,0.25 2.375,2.906 2.135,2.813 false 1.833,2.906 1.594,2.813 false 2.708,1.458 3.24,1.865 3.24,1.865 3.458,1.865 true 1.167,0.323 1.479,0.479 0.313,0.156 10 false *a 1.406,2.74 1.719,2.896 0.313,0.156 10 false *b 1.948,2.729 2.26,2.885 0.313,0.156 10 false *c 3.896,2.792 4.208,2.948 0.313,0.156 10 false *d 3.917,3.198 4.229,3.354 0.313,0.156 10 false *e 2.073,3.281 2.385,3.438 0.313,0.156 10 false *f 2.448,3.281 2.76,3.438 0.313,0.156 10 false *g 2.604,3.646 2.917,3.802 0.313,0.156 10 false *h 1.521,4.177 1.833,4.333 0.313,0.156 10 false *i 3.542,4.177 3.854,4.333 0.313,0.156 10 false *j 2.375,0.313 2.833,0.51 0.458,0.198 10 false Q16 3.521,1.771 3.979,1.969 0.458,0.198 10 false IOUT 0.844,2.583 1.302,2.781 0.458,0.198 10 false HI 0.844,3.042 1.302,3.24 0.458,0.198 10 false LO
*a Component with harness connected
(Map Light Assembly)
*b IOUT Initial Signal
*c IOUT Initial Response *d Approximately 1.0 seconds
*e Initial Diagnosis *f Approximately 1.0 to 1.6 seconds
*g Approximately 0.05 seconds *h Approximately 5.5 seconds
*i Disarmed State *j Arming Preparation State
*k HI *l LO


Measurement Condition
Tester Connection Content
Tester Connection Q16-14 (IOUT) - Body ground
Tool Setting 2 V/DIV., 100 ms./DIV.
Condition Theft deterrent system is set (system changes from disarmed state to arming preparation state)

HINT:
·

If the intrusion sensor (theft warning ultrasonic sensor) is normal, an initial response is output in response to the HI input from the main body ECU (multiplex network body ECU).

·

If the waveform output remains LO, there may be a problem with the main body ECU (multiplex network body ECU), as there is no input from the main body ECU (multiplex network body ECU).



OK:

The waveform displays properly (HI is 6.5 V or higher and LO is below 1 V).



Result:
Result Proceed to
NG (Waveform output remains LO) A
NG (There is no initial response and the waveform output remains HI) B
OK (There is an initial response) C



A

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - MAP LIGHT ASSEMBLY)

B

C

4.REPLACE MAP LIGHT ASSEMBLY
3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - MAP LIGHT ASSEMBLY)
a.

Disconnect the G79 main body ECU (multiplex network body ECU) connector.


b.

Disconnect the Q16 map light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G79-12 (ISIF) - Q16-14 (IOUT) Always Below 1 Ω
G79-12 (ISIF) - Body ground Always 10 kΩ or higher
Q16-14 (IOUT) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE MAP LIGHT ASSEMBLY
a.

Temporarily replace the map light assembly with a new or normally functioning one.

Click hereVehicle Interior>LIGHTING (INT)>ROOM LIGHT>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.CHECK FOR DTC
5.CHECK FOR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>THEFT DETERRENT SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Clear DTCs
50002 123

b.

Turn the ignition switch to ON, then off.


c.

Set the theft deterrent system to "ARMED STATE".


d.

Check that the security indicator changes from illuminated to blinking.


e.

Set the theft deterrent system to "DISARMED STATE".


f.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>THEFT DETERRENT SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Trouble Codes
50001 123

Result:
Proceed to
DTC B2762 is not output
DTC B2762 is output



DTC B2762 is not output

END (MAP LIGHT ASSEMBLY WAS DEFECTIVE)

DTC B2762 is output

REPLACE INTRUSION SENSOR (THEFT WARNING ULTRASONIC SENSOR)