Home › Vehicle Interior › INTERIOR PANELS / TRIM › ROOF HEADLINING › from 2015.10
RM3090E _58 Vehicle Interior _008791 INTERIOR PANELS / TRIM _0049317 ROOF HEADLINING A

INTERIOR PANELS / TRIM  ROOF HEADLINING  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1.INSTALL TONNEAU COVER STOPPER

HINT:

Use the same procedure for both tonneau cover stoppers.


a.
B426259

Install the tonneau cover stopper with the 2 screws.


Hide 2.INSTALL TONNEAU COVER STOPPER SILENCER (w/ Silencer)

HINT:

Use the same procedure for both tonneau cover stopper silencers.


a.
B426258

Install a new tonneau cover stopper silencer in the location shown in the illustration using double-sided tape.


Hide 86101J 3.INSTALL NO. 2 ANTENNA CORD SUB-ASSEMBLY

Hide 82171 4.INSTALL NO. 1 ROOF WIRE

a.

w/o Sliding Roof:

i.

Apply new double-sided tape as shown in the illustration.

B439330C01
4.875,4.917 5.188,5.073 0.313,0.156 10 false *a 5.604,5.365 5.917,5.521 0.313,0.156 10 false *b
*a 1 mm (0.0394 in.) *b 15 mm (0.590 in.)
V100146

Double-sided Tape - -



ii.

Attach the No. 1 roof wire to the double-sided tape.


iii.

Apply new one-sided tape.


iv.

Turn the 2 connectors approximately 90° counter clockwise to connect them.


v.

If any slack forms, take up the slack in the areas A shown in the illustration.

NOTICE:

Secure any wire that protrudes from the double-sided tape with one-sided tape.



vi.

Check that the No. 1 roof wire is not twisted, raised, or protruding in any way.

B438458C01
6.448,5.188 6.615,5.188 6.615,5.188 6.563,4.927 false 1.531,0.781 1.844,0.938 0.313,0.156 10 false *A 1.76,0.76 1.979,0.917 0.219,0.156 10 false *B 1.177,0.823 1.49,0.979 0.313,0.156 10 false *E 2.115,0.438 2.427,0.594 0.313,0.156 10 false *D 6.292,5.104 6.604,5.26 0.313,0.156 10 false *1 0.958,3.76 1.271,3.917 0.313,0.156 10 false *a 1.854,0.552 2.167,0.708 0.313,0.156 10 false *C 2.74,3.104 2.885,3.281 0.146,0.177 10 true A 6.073,4.396 6.219,4.573 0.146,0.177 10 true A 2.75,4.021 2.896,4.198 0.146,0.177 10 true A
*A w/ EC Mirror, w/o Pre-crash Safety System *B w/ EC Mirror, w/ Pre-crash Safety System
*C w/ Rain Sensor, w/o Pre-crash Safety System *D w/ Rain Sensor, w/ Pre-crash Safety System
*E w/ Pre-crash Safety System - -
*1 No. 1 Roof Wire - -
*a 90° - -
V100146

One-sided Tape
V100155

Double-sided Tape




b.

w/ Sliding Roof:

i.

Apply new double-sided tape as shown in the illustration.

B439331C01
4.896,4.938 5.208,5.094 0.313,0.156 10 false *a 5.604,5.354 5.917,5.51 0.313,0.156 10 false *b
*a 1 mm (0.0394 in.) *b 15 mm (0.590 in.)
V100146

Double-sided Tape - -



ii.

Attach the No. 1 roof wire to the double-sided tape.


iii.

Apply new one-sided tape.


iv.

Turn the 2 connectors approximately 90° counter clockwise to connect them.


v.

If any slack forms, take up the slack in the areas A shown in the illustration.

NOTICE:

Secure any wire that protrudes from the double-sided tape with one-sided tape.



vi.

Check that the No. 1 roof wire is not twisted, raised, or protruding in any way.

B438459C01
6.552,5.156 6.74,5.156 6.74,5.156 6.615,4.927 false 1.865,0.552 2.177,0.708 0.313,0.156 10 false *C 1.479,0.792 1.708,0.948 0.229,0.156 10 false *A 1.74,0.781 1.99,0.938 0.25,0.156 10 false *B 1.146,0.854 1.458,1.01 0.313,0.156 10 false *E 2.104,0.458 2.417,0.615 0.313,0.156 10 false *D 6.396,5.063 6.708,5.219 0.313,0.156 10 false *1 0.969,3.771 1.281,3.927 0.313,0.156 10 false *a 2.573,3.26 2.729,3.458 0.156,0.198 10 false A 2.583,3.917 2.74,4.115 0.156,0.198 10 false A 6.083,4.396 6.24,4.594 0.156,0.198 10 false A
*A w/ EC Mirror, w/o Pre-crash Safety System *B w/ EC Mirror, w/ Pre-crash Safety System
*C w/ Rain Sensor, w/o Pre-crash Safety System *D w/ Rain Sensor, w/ Pre-crash Safety System
*E w/ Pre-crash Safety System - -
*1 No. 1 Roof Wire - -
*a 90° - -
V100146

One-sided Tape
V100155

Double-sided Tape




Hide 81340J 5.INSTALL VANITY LIGHT ASSEMBLY LH

a.

Attach the claw to install the vanity light assembly LH.


b.

Attach the 2 claws to connect the bulb holder to the vanity light assembly LH.


Hide 81340H 6.INSTALL VANITY LIGHT ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 63352D 7.INSTALL NO. 2 ROOF HEADLINING PAD (for Cold Area)

a.
B438772C01
0,0 0,0 false
V100146

Silencer Marking


Install a new No. 2 roof headlining pad using double-sided tape, hot-melt glue or adhesive as shown in the illustration.


Hide 63351B 8.INSTALL ROOF HEADLINING PAD (for Cold Area)

HINT:

Use the same procedure for both roof headlining pads.


a.
B337932C01
1.854,0.906 1.938,1.563 0.083,0.656 10 false .
V100146

Silencer Marking


Install a new roof headlining pad using double-sided tape, hot-melt glue or adhesive as shown in the illustration.


Hide 63343 9.INSTALL NO. 3 ROOF SILENCER PAD

a.
B337936C01
1.229,2.292 1.385,2.49 0.156,0.198 10 false .
V100146

Silencer Marking


Install a new No. 3 roof silencer pad using double-sided tape, hot-melt glue or adhesive as shown in the illustration.


Hide 63341 10.INSTALL NO. 1 ROOF SILENCER PAD (w/o Sliding Roof)

a.

Install a new No. 1 roof silencer pad using double-sided tape, hot-melt glue or adhesive as shown in the illustration.

B337934C01
4.771,1.552 4.927,1.75 0.156,0.198 10 false .
V100146

Silencer Marking - -



Hide 63341 11.INSTALL NO. 1 ROOF SILENCER PAD (w/ Sliding Roof)

a.
B337935C01
1.417,2.385 1.573,2.583 0.156,0.198 10 false .
V100146

Silencer Marking


Install a new No. 2 roof silencer pad using double-sided tape, hot-melt glue or adhesive as shown in the illustration.


Hide 63353C 12.INSTALL CENTER ROOF HEADLINING PAD

a.

Install a new center roof headlining pads using double-sided tape, hot-melt glue or adhesive as shown in the illustration.

B367337C01
1.302,1.875 1.052,1.875 1.052,1.875 1.01,1.583 true 3.427,1.875 3.708,1.875 3.708,1.875 3.844,1.552 true 5.635,1.604 5.635,1.135 true 5.865,0.948 6.24,0.948 6.24,0.948 6.24,1.313 true 6.24,1.208 6.073,1.208 true 5.844,1.354 5.646,1.354 true 0.333,0.677 0.646,0.833 0.313,0.156 10 true *A 2.698,0.677 3.01,0.833 0.313,0.156 10 true *B 5.031,0.667 5.344,0.823 0.313,0.156 10 true *C 1.333,1.771 1.646,1.927 0.313,0.156 10 true *a 3.271,1.771 3.583,1.927 0.313,0.156 10 true *a 6.146,1.323 6.448,1.521 0.302,0.198 10 true *a 5.542,1.625 5.813,1.823 0.271,0.198 10 true *a
*A for RH Side *B for LH Side, Type A
*C for LH Side, Type B - -
*a Silencer Marking - -