Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM › from 2015.10
RM3090E _56 Audio / Visual / Telematics _008432 PARK ASSIST / MONITORING _0232444 PANORAMIC VIEW MONITOR SYSTEM Y

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM  HOW TO PROCEED WITH TROUBLESHOOTING  


CAUTION / NOTICE / HINT

HINT:
·

Use the following procedure to troubleshoot the panoramic view monitor system.

·

*: Use the GTS.



PROCEDURE

1.VEHICLE BROUGHT TO WORKSHOP
Result:
Proceed to
NEXT



NEXT

2.INSPECT BATTERY VOLTAGE
2.INSPECT BATTERY VOLTAGE
a.

Measure the battery voltage with the engine switch off.

Standard voltage:

11 to 14 V


If the voltage is below 11 V, replace or recharge the battery before proceeding.


Result:
Proceed to
NEXT



NEXT

3.CHECK VEHICLE TYPE
3.CHECK VEHICLE TYPE
Result:
Result Proceed to
w/ Audio and Visual System (for Radio and Display Type) A
w/ Navigation System B



A

4.CHECK AUDIO AND VISUAL SYSTEM

B

11.CHECK NAVIGATION SYSTEM
4.CHECK AUDIO AND VISUAL SYSTEM
a.

Refer to the audio and visual system.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio and Display Type)>PROBLEM SYMPTOMS TABLE

OK:

Audio and visual system is normal.



Result:
Proceed to
OK
NG



OK

5.CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*

NG

5.CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*
a.

Use the GTS to check if the CAN communication system is functioning normally.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING


Result:
Result Proceed to
CAN DTCs are not output A
CAN DTCs are output B



A

6.CHECK FOR DTC*

B

6.CHECK FOR DTC*
a.

Check for DTCs and note any codes that are output.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>DTC CHECK / CLEAR

Chassis > Panoramic View Monitor > Trouble Codes
50001 353

b.

Clear the DTCs.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>DTC CHECK / CLEAR

Chassis > Panoramic View Monitor > Clear DTCs
50002 353

c.

Recheck for DTCs. Try to prompt the DTC by simulating the original activity that the DTC suggests.

Chassis > Panoramic View Monitor > Trouble Codes
50001 353

Result:
Result Proceed to
DTC is not output A
DTC is output B



A

7.PROBLEM SYMPTOMS TABLE

B

9.ADJUST, REPAIR OR REPLACE
7.PROBLEM SYMPTOMS TABLE

Result:
Result Proceed to
Fault is not listed in Problem Symptoms Table A
Fault is listed in Problem Symptoms Table B



A

8.OVERALL ANALYSIS AND TROUBLESHOOTING*

B

ADJUST, REPAIR OR REPLACE IN ACCORDANCE WITH PROBLEM SYMPTOMS TABLE

8.OVERALL ANALYSIS AND TROUBLESHOOTING*

NEXT

9.ADJUST, REPAIR OR REPLACE
9.ADJUST, REPAIR OR REPLACE
Result:
Proceed to
NEXT



NEXT

10.CONFIRMATION TEST
10.CONFIRMATION TEST
Result:
Proceed to
NEXT



NEXT

END

11.CHECK NAVIGATION SYSTEM
a.

Refer to the navigation system.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for SD)>PROBLEM SYMPTOMS TABLE

OK:

Navigation system is normal.



Result:
Proceed to
OK
NG



OK

5.CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*

NG