Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM › from 2015.10
RM3090E _56 Audio / Visual / Telematics _008432 PARK ASSIST / MONITORING _0232444 PANORAMIC VIEW MONITOR SYSTEM D

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM  DIAGNOSIS SYSTEM  


PARKING ASSIST MONITOR DIAGNOSIS SYSTEM


a.

For panoramic view monitor system diagnosis, signals received by the parking assist ECU can be checked, and the panoramic view monitor system can be calibrated, adjusted and checked using the navigation receiver assembly*1 or radio and display receiver assembly*2.

*1: w/ Navigation System

*2: w/ Audio and Visual System (for Radio and Display Type)


NOTICE:

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>CALIBRATION


HINT:

The displayed screens and items may differ depending on vehicle specifications.




DIAGNOSIS SCREEN TRANSITION (VIEW ADJUSTMENT)


E340701E01
2.76,0.938 5.969,1.135 3.208,0.198 10 false Start diagnostic mode


DIAGNOSIS SCREEN TRANSITION (STEERING ANGLE SETTING)


E340702E01
2.802,0.938 6.01,1.135 3.208,0.198 10 false Start diagnostic mode


DIAGNOSIS SCREEN TRANSITION (BODY COLOR SETTING)


E335972E01
2.76,0.99 5.969,1.188 3.208,0.198 10 false Start diagnostic mode



SIGNAL CHECK (parking assist ECU input signal)


a.

Start diagnostic mode.


i.
E271944

Select "Function Check/Setting" on the "Service Menu" screen to display the "Function Check/Setting I" screen.


ii.
E314875

Select "Camera Setting" on the "Function Check/Setting I" screen.

HINT:

After "Camera Setting" is selected, the screen transitions differ depending on whether initialization of the parking assist ECU was performed after parking assist ECU replacement.

Parking Assist ECU Initialization Screen Transition
Not performed "Signal Check" screen
Performed "Mode Setting" screen



iii.
E296733

When the screen changes to the "Mode Setting" screen, select "View Adjustment" to display the "Signal Check" screen.

HINT:

To select a grayed out item, select and hold the item for 2 seconds or more.




b.

Signal check

i.
E340700

On the "Signal Check" screen, it is possible to inspect the state of signals sent to the parking assist ECU and check the settings.

Item Inspection Detail Note
CAN Speed signal input When "CHK" (red) is displayed, selecting "Next" will not change to the next screen.
CAMERA SW Telltale light assembly (panoramic view monitor main switch) signal input
SHIFT Shift information input

HINT:
·

When "CHK" (red) is displayed, perform inspections based on the result of the following inspections.

·

If performing the adjustment after proceeding to the next screen, confirm that all items display "OK" (blue) before selecting "Next".





c.

CAN inspection

HINT:

If "CHK" (red) is displayed for "CAN", check for DTCs and perform troubleshooting based on the output DTCs.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>"CHK" message(s) are displayed on the SIGNAL CHECK screen.



d.

CAMERA SW inspection

i.

Check that "OK" (blue) is displayed for "CAMERA SW" and select "OK".

HINT:

If "CHK" (red) remains displayed or the "CAMERA SW" inspection result is not normal, perform troubleshooting according to the Problem Symptoms Table ("CHK" message(s) are displayed on the "Signal Check" screen).

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>"CHK" message(s) are displayed on the SIGNAL CHECK screen.




e.

SHIFT inspection

i.

Check that "OK" (blue) is displayed for "SHIFT" and select "OK".

HINT:

If "CHK" (red) remains displayed or the "SHIFT" inspection result is not normal, perform troubleshooting according to the Problem Symptoms Table ("CHK" message(s) are displayed on the "Signal Check" screen)

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>"CHK" message(s) are displayed on the SIGNAL CHECK screen.






Body Color Setting


HINT:
·

This function is used for only customers who request it

·

The color of the vehicle icon displayed on the moving view screen or the panoramic view screen can be changed from the diagnosis screen.



a.

Start diagnostic mode.


i.
E271944

Select "Function Check/Setting" on the "Service Menu" screen.


ii.
E314875

Select "Camera Setting" on the "Function Check/Setting I" screen.


iii.
E296733

Select "Body Color Setting" on the "Mode Setting" screen to display the "Body Color Setting" screen.



b.

Body color setting

i.
E335951

Select the color to change, and display the result confirm screen.

HINT:

"White" is initialized.



ii.
E335952

Select "OK" on the result confirm screen, and display the mode setting screen.

NOTICE:

Changing the color of the icon may make the icon border hard to see on the moving view screen or panoramic view screen.


HINT:
·

The body color setting screen does not display the actual body color.

·

To change the body color setting again, select "Back" and select it again.

·

The setting is memorized when the mode setting screen is displayed.







CALIBRATION WHEN SERVICING VEHICLE


NOTICE:

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>CALIBRATION