Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM › from 2015.10
RM3090E _56 Audio / Visual / Telematics _008432 PARK ASSIST / MONITORING _0232444 PANORAMIC VIEW MONITOR SYSTEM J

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM  "CHK" message(s) are displayed on the SIGNAL CHECK screen.  


DESCRIPTION

On the SIGNAL CHECK screen, it is possible to check if the signals sent to the parking assist ECU are normal.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>DTC CHECK / CLEAR

HINT:
·

On the SIGNAL CHECK screen, "OK" (blue) is displayed for items with a normal inspection result or input state.

·

On the SIGNAL CHECK screen, "CHK" (red) is displayed for items with an abnormal inspection result or input state.

·

Displayed items may differ depending on vehicle specifications.



Item Signal Input Method Detail DTC Output when Abnormal Result is Displayed Signal Receiver
CAN CAN communication CAN communication signal DTC is output Related ECUs
CAMERA SW Vehicle wire harness Telltale light assembly (panoramic view monitor main switch) signal input state DTC is not output Telltale Light Assembly (Panoramic View Monitor Main Switch)
SHIFT Vehicle wire harness Shift information signal DTC is output Park/neutral position switch assembly

WIRING DIAGRAM

E287159E14
0.917,2.271 2.792,2.49 1.875,0.219 10 false : CAN Communication Line 2.427,1.479 4.542,1.656 2.115,0.177 10 false to CAN Communication System 5.094,2.135 6.094,2.333 1,0.198 10 false a2 5.094,2.302 6.958,2.542 1.865,0.24 10 false Parking Assist ECU 4.865,0.438 5.115,0.604 0.25,0.167 10 false 20 5.135,0.542 5.552,0.708 0.417,0.167 10 false BLSW 1.708,0.76 2.042,0.927 0.333,0.167 10 false G43 1.719,0.917 4.177,1.333 2.458,0.417 10 false Telltale Light Assembly (Panoramic View Monitor Main Switch) 1.813,0.448 2.167,0.646 0.354,0.198 10 false 13 3.229,0.438 3.479,0.604 0.25,0.167 10 false 20 2.083,0.438 2.25,0.604 0.167,0.167 10 false E 3.031,0.438 3.198,0.604 0.167,0.167 10 false D

CAUTION / NOTICE / HINT

NOTICE:
·

When "!" mark is displayed on the multi-display after the battery cable is disconnected, correct the steering angle neutral point.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>INITIALIZATION

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>CALIBRATION



PROCEDURE

1.CHECK DISPLAY CHECK MODE
a.
E340700

Check which items display on the signal check screen.


Result:
Result Proceed to
"CAMERA SW" displays "CHK" (red) A
"CAN" displays "CHK" (red) B
"SHIFT" displays "CHK" (red) (for Navigation Receiver Type) C
"SHIFT" displays "CHK" (red) (for Radio and Display Type) D



A

2.CHECK HARNESS AND CONNECTOR (TELLTALE LIGHT ASSEMBLY [PANORAMIC VIEW MONITOR MAIN SWITCH] - PARKING ASSIST ECU AND BODY GROUND)

B

C

D

2.CHECK HARNESS AND CONNECTOR (TELLTALE LIGHT ASSEMBLY [PANORAMIC VIEW MONITOR MAIN SWITCH] - PARKING ASSIST ECU AND BODY GROUND)
a.

Disconnect the G43 telltale light assembly (panoramic view monitor main switch) connector.


b.

Disconnect the a2 parking assist ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
a2-20 (BLSW) - G43-20 (D) Always Below 1 Ω
G43-13 (E) - Body ground Always Below 1 Ω
a2-20 (BLSW) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT TELLTALE LIGHT ASSEMBLY (PANORAMIC VIEW MONITOR MAIN SWITCH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT TELLTALE LIGHT ASSEMBLY (PANORAMIC VIEW MONITOR MAIN SWITCH)
a.

Remove the telltale light assembly (panoramic view monitor main switch).

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SWITCH>REMOVAL


b.

Inspect the telltale light assembly (panoramic view monitor main switch).

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

NG

REPLACE TELLTALE LIGHT ASSEMBLY (PANORAMIC VIEW MONITOR MAIN SWITCH)