Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM › from 2015.10
RM3090E _56 Audio / Visual / Telematics _008432 PARK ASSIST / MONITORING _0232444 PANORAMIC VIEW MONITOR SYSTEM C

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM  C1621  Back Camera Power Supply Failure  C1622  Open or Short Circuit in Back Camera Signal  


DESCRIPTION

DTC C1621 is stored if the parking assist ECU determines that the input/output signal communication with the rear television camera assembly is abnormal.

DTC C1622 is stored if the parking assist ECU judges as a result of its self check that the signals or signal lines between the parking assist ECU and the rear television camera assembly are not normal.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1621 Back Camera Power Supply Failure Rear television camera assembly power supply malfunction
·

Harness or connector

·

Rear television camera assembly

·

Parking assist ECU


C1622 Open or Short Circuit in Back Camera Signal Open or short in the rear television camera signal circuit
·

Harness or connector

·

Rear television camera assembly

·

Parking assist ECU



WIRING DIAGRAM

E297862E07
1.302,0.792 1.76,0.99 0.458,0.198 10 false CB+ 1.302,1.208 1.76,1.406 0.458,0.198 10 false CV+ 1.313,1.625 1.771,1.823 0.458,0.198 10 false CV- 1.188,2.031 1.646,2.229 0.458,0.198 10 false CGND 0.5,2.49 0.958,2.688 0.458,0.198 10 false c3 0.479,2.625 2.698,2.833 2.219,0.208 10 false Rear Television Camera Assembly 5.583,0.781 6.042,0.979 0.458,0.198 10 false CB+ 5.479,2.469 6.708,2.656 1.229,0.188 10 false a1 5.583,1.188 6.042,1.385 0.458,0.198 10 false CV+ 5.479,2.615 6.833,2.844 1.354,0.229 10 false Parking Assist ECU 5.604,1.625 6.063,1.823 0.458,0.198 10 false CV- 5.552,2.042 6.01,2.24 0.458,0.198 10 false CGND 1.688,0.688 2.156,0.844 0.469,0.156 10 false 6 1.698,1.094 2.167,1.25 0.469,0.156 10 false 3 1.698,1.5 2.167,1.656 0.469,0.156 10 false 2 1.708,1.927 2.177,2.083 0.469,0.156 10 false 5 5.365,0.656 5.542,0.854 0.177,0.198 10 false 3 5.354,1.083 5.531,1.281 0.177,0.198 10 false 1 5.354,1.479 5.521,1.656 0.167,0.177 10 false 2 5.354,1.917 5.521,2.094 0.167,0.177 10 false 9 0.167,3.354 1.813,3.563 1.646,0.208 10 false *: Shielded 2.469,2.156 2.927,2.354 0.458,0.198 10 false * 3.323,2.156 3.781,2.354 0.458,0.198 10 false * 4.125,2.167 4.583,2.365 0.458,0.198 10 false * 4.948,2.177 5.406,2.375 0.458,0.198 10 false *

CAUTION / NOTICE / HINT

NOTICE:
·

When "!" mark is displayed on the multi-display after the cable is disconnected from the negative (-) battery terminal, correct the steering angle neutral point.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>INITIALIZATION

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>CALIBRATION



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - REAR TELEVISION CAMERA ASSEMBLY)
a.

Disconnect the a1 parking assist ECU connector.


b.

Disconnect the c3 rear television camera assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
a1-3 (CB+) - c3-6 (CB+) Always Below 1 Ω
a1-1 (CV+) - c3-3 (CV+) Always Below 1 Ω
a1-2 (CV-) - c3-2 (CV-) Always Below 1 Ω
a1-9 (CGND) - c3-5 (CGND) Always Below 1 Ω
a1-3 (CB+) or c3-6 (CB+) - Body ground Always 10 kΩ or higher
a1-1 (CV+) or c3-3 (CV+) - Body ground Always 10 kΩ or higher
a1-2 (CV-) or c3-2 (CV-) - Body ground Always 10 kΩ or higher
a1-9 (CGND) or c3-5 (CGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK PARKING ASSIST ECU (CB+, CGND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK PARKING ASSIST ECU (CB+, CGND)
a.
E272332C60
1.51,0.188 1.927,0.427 0.417,0.24 2.344,1.25 2.542,1.958 2.542,1.958 2.729,1.958 true 2.365,1.063 2.75,0.677 2.75,0.677 2.938,0.677 true 0.135,0.104 0.448,0.302 0.313,0.198 10 false *a 3.01,0.604 3.354,0.792 0.344,0.188 10 false CB+ 2.823,1.875 3.25,2.063 0.427,0.188 10 false CGND 1.625,0.219 2.083,0.417 0.458,0.198 10 false a1
*a Component with harness connected
(Parking Assist ECU)


Remove the parking assist ECU with the connector still connected.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
a1-9 (CGND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
a1-3 (CB+) - a1-9 (CGND) Engine switch on (IG) 5.5 to 7.05 V



Result:
Proceed to
OK
NG



OK

3.CHECK REAR TELEVISION CAMERA ASSEMBLY

NG

3.CHECK REAR TELEVISION CAMERA ASSEMBLY
a.

Remove the parking assist ECU with the connector still connected.

E272333C61
1.313,0.438 1.719,0.656 0.406,0.219 2.042,1.5 1.677,2.479 1.677,2.479 1.552,2.479 true 2.24,1.354 2.531,2.365 2.531,2.365 2.698,2.365 true 3.458,1.823 3.583,2.417 3.583,2.417 3.667,2.417 false 3.563,1.802 4.167,2.417 4.167,2.417 4.333,2.417 false 5.667,1.698 5.5,2.417 5.5,2.417 5.333,2.417 false 5.792,1.646 6,2.417 6,2.417 6.167,2.417 false 0.125,0.094 0.438,0.292 0.313,0.198 10 false *a 1.438,0.448 1.896,0.646 0.458,0.198 10 false a1 1.083,2.417 1.542,2.615 0.458,0.198 10 false CGND 2.76,2.281 3.219,2.479 0.458,0.198 10 false CV+ 2.729,1.302 3.188,1.5 0.458,0.198 10 false GND 4.865,1.302 5.323,1.5 0.458,0.198 10 false GND 3.021,0.406 3.333,0.604 0.313,0.198 10 false *b 5.125,0.406 5.438,0.604 0.313,0.198 10 false *c 3.719,2.354 4.031,2.552 0.313,0.198 10 false *d 5.167,2.344 5.479,2.542 0.313,0.198 10 false *d 4.396,2.344 4.708,2.542 0.313,0.198 10 false *e 6.208,2.333 6.521,2.531 0.313,0.198 10 false *e
*a Component with harness connected
(Parking Assist ECU)
*b Waveform 1
*c Waveform 2 *d Synchronization Signal
*e Video Waveform - -



b.

Check the waveform of the rear television camera assembly using an oscilloscope.

HINT:

The video waveform changes according to the image sent by the rear television camera assembly.


Measurement Condition
Item Content
Terminal No. (Symbol) a1-1 (CV+) - a1-9 (CGND)
Tool Setting 200 mV/DIV., 50 μsec./DIV.
Condition
·

Waveform 1: Engine switch on (IG), telltale light assembly (panoramic view monitor main switch) on, camera lens not covered, displaying image

·

Waveform 2: Engine switch on (IG), telltale light assembly (panoramic view monitor main switch) on, camera lens covered, blacking out screen



OK:

Waveform is as shown in the illustration.



Result:
Proceed to
OK
NG



OK

NG