Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM › from 2015.10
RM3090E _56 Audio / Visual / Telematics _008432 PARK ASSIST / MONITORING _0232444 PANORAMIC VIEW MONITOR SYSTEM C

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM  C1681  Front Camera Feedback Malfunction  C1682  Front Camera Current Malfunction  


DESCRIPTION

DTC C1681 is stored if the parking assist ECU judges as a result of its self check that a synchronization problem is occurring in the image signal sent from the front television camera assembly to the parking assist ECU.

DTC C1682 is stored if the parking assist ECU judges as a result of its self check that there is a problem with the current supplied from the front television camera assembly connected to the parking assist ECU.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1681 Front Camera Feedback Malfunction Open or short in the front television camera signal circuit
·

Harness or connector

·

Front television camera assembly

·

Parking assist ECU


C1682 Front Camera Current Malfunction Front television camera power supply failure
·

Harness or connector

·

Front television camera assembly

·

Parking assist ECU



WIRING DIAGRAM

E334734E02
0.063,2.344 2.375,2.594 2.313,0.25 10 false Front Television Camera Assembly 0.073,2.156 0.469,2.417 0.396,0.26 10 false Z5 0.927,0.5 1.375,0.708 0.448,0.208 10 false BCB+ 0.917,0.917 1.365,1.125 0.448,0.208 10 false BCV+ 0.938,1.333 1.385,1.542 0.448,0.208 10 false BCV- 0.896,1.74 1.344,1.948 0.448,0.208 10 false BGND 1.458,0.354 1.615,0.552 0.156,0.198 10 false 6 1.458,0.781 1.615,0.979 0.156,0.198 10 false 3 1.458,1.198 1.615,1.396 0.156,0.198 10 false 2 1.458,1.604 1.615,1.802 0.156,0.198 10 false 5 5.698,2.198 6.688,2.375 0.99,0.177 10 false a1 5.729,2.385 7.094,2.635 1.365,0.25 10 false Parking Assist ECU 5.042,1.896 5.26,2.104 0.219,0.208 10 false * 0.208,3.083 1.552,3.313 1.344,0.229 10 false *: Shielded 5.927,0.49 6.542,0.688 0.615,0.198 10 false BCB+ 5.927,0.927 6.542,1.125 0.615,0.198 10 false BCV+ 5.927,1.323 6.542,1.521 0.615,0.198 10 false BCV- 5.938,1.74 6.552,1.938 0.615,0.198 10 false BGND 5.615,0.354 5.844,0.552 0.229,0.198 10 false 15 5.625,0.771 5.854,0.969 0.229,0.198 10 false 13 5.625,1.188 5.854,1.385 0.229,0.198 10 false 14 5.646,1.625 5.875,1.823 0.229,0.198 10 false 27 4.021,1.896 4.24,2.104 0.219,0.208 10 false * 3.021,1.906 3.24,2.115 0.219,0.208 10 false * 2.073,1.917 2.292,2.125 0.219,0.208 10 false *

CAUTION / NOTICE / HINT

NOTICE:
·

When "!" mark is displayed on the multi-display after the cable is disconnected from the negative (-) battery terminal, correct the steering angle neutral point.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>INITIALIZATION

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as panoramic view monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>CALIBRATION



PROCEDURE

1.CHECK FOR DTC
a.

Clear the DTCs.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>DTC CHECK / CLEAR

Chassis > Panoramic View Monitor > Clear DTCs
50002 353

b.

Check for DTCs.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>DTC CHECK / CLEAR

Chassis > Panoramic View Monitor > Trouble Codes
50001 353
OK:

DTCs C1681 and C1682 are not output.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - FRONT TELEVISION CAMERA ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - FRONT TELEVISION CAMERA ASSEMBLY)
a.

Disconnect the a1 parking assist ECU connector.


b.

Disconnect the Z5 front television camera assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
a1-15 (BCB+) - Z5-6 (BCB+) Always Below 1 Ω
a1-13 (BCV+) - Z5-3 (BCV+) Always Below 1 Ω
a1-14 (BCV-) - Z5-2 (BCV-) Always Below 1 Ω
a1-27 (BGND) - Z5-5 (BGND) Always Below 1 Ω
a1-15 (BCB+) or Z5-6 (BCB+) - Body ground Always 10 kΩ or higher
a1-13 (BCV+) or Z5-3 (BCV+) - Body ground Always 10 kΩ or higher
a1-14 (BCV-) or Z5-2 (BCV-) - Body ground Always 10 kΩ or higher
a1-27 (BGND) or Z5-5 (BGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK PARKING ASSIST ECU (BCB+, BGND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK PARKING ASSIST ECU (BCB+, BGND)
a.
E272332C61
1.49,0.208 1.906,0.448 0.417,0.24 1.323,1.385 2.031,1.979 2.031,1.979 2.219,1.979 true 1.323,1.208 0.635,0.781 0.635,0.781 0.51,0.781 true 0.135,0.104 0.448,0.302 0.313,0.198 10 false *a 0.083,0.698 0.51,0.885 0.427,0.188 10 false BCB+ 2.271,1.906 2.698,2.094 0.427,0.188 10 false BGND 1.615,0.229 2.073,0.427 0.458,0.198 10 false a1
*a Component with harness connected
(Parking Assist ECU)


Remove the parking assist ECU with the connector still connected.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
a1-27 (BGND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
a1-15 (BCB+) - a1-27 (BGND) Engine switch on (IG) 5.5 to 7.05 V



Result:
Proceed to
OK
NG



OK

4.CHECK FRONT TELEVISION CAMERA ASSEMBLY

NG

4.CHECK FRONT TELEVISION CAMERA ASSEMBLY
a.

Remove the parking assist ECU with the connector still connected.

E272333C54
1.313,0.396 1.719,0.615 0.406,0.219 1.156,1.635 0.708,2.427 0.708,2.427 0.583,2.427 true 1.385,1.5 1.771,2.51 1.771,2.51 1.938,2.51 true 3.458,1.823 3.583,2.417 3.583,2.417 3.667,2.417 false 3.563,1.802 4.167,2.417 4.167,2.417 4.333,2.417 false 5.667,1.698 5.5,2.417 5.5,2.417 5.333,2.417 false 5.792,1.646 6,2.417 6,2.417 6.167,2.417 false 0.125,0.094 0.438,0.292 0.313,0.198 10 false *a 1.406,0.417 1.865,0.615 0.458,0.198 10 false a1 0.115,2.354 0.573,2.552 0.458,0.198 10 false BGND 1.99,2.438 2.448,2.635 0.458,0.198 10 false BCV+ 2.729,1.302 3.188,1.5 0.458,0.198 10 false GND 4.865,1.302 5.323,1.5 0.458,0.198 10 false GND 3.021,0.406 3.333,0.604 0.313,0.198 10 false *b 5.125,0.406 5.438,0.604 0.313,0.198 10 false *c 3.719,2.354 4.031,2.552 0.313,0.198 10 false *d 5.167,2.344 5.479,2.542 0.313,0.198 10 false *d 4.396,2.344 4.708,2.542 0.313,0.198 10 false *e 6.208,2.333 6.521,2.531 0.313,0.198 10 false *e
*a Component with harness connected
(Parking Assist ECU)
*b Waveform 1
*c Waveform 2 *d Synchronization Signal
*e Video Waveform - -



b.

Using an oscilloscope, check the waveform.

HINT:
·

A waterproof connector is used for the front television camera assembly. Therefore, inspect the waveform at the parking assist ECU with the connector connected.

·

The video waveform changes according to the image sent by the front television camera assembly.



OK:

Waveform is as shown in the illustration.


Measurement Condition
Item Content
Terminal No. (Symbol) a1-13 (BCV+) - a1-27 (BGND)
Tool Setting 200 mV/DIV., 50 μs/DIV.
Condition
·

Waveform 1: Engine switch on (IG), telltale light assembly (panoramic view monitor main switch) on, camera lens not covered, displaying image

·

Waveform 2: Engine switch on (IG), telltale light assembly (panoramic view monitor main switch) on, camera lens covered, blacking out screen




Result:
Proceed to
OK
NG



OK

NG