CHECK DRIVING SUPPORT ECU ASSEMBLY
Disconnect the G168 driving support ECU assembly connector.
If a load of more than 10 kg (22 lb) is placed on the connector, it may break. Do not place more load than is necessary on the connector.
Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
|
*1: w/o Stop and Start System *2: w/ Stop and Start System |
||||
| G168-28 (GND) - Body ground | BR - Body ground | Ground | Always | Below 1 Ω |
| G168-7 (B) - Body ground | B - Body ground*1
V - Body ground*2 |
Power source | Ignition switch ON | 11 to 14 V*1
9.5 to 14 V*2 |
| Ignition switch off | Below 1 V | |||
If the result is not as specified, there may be a malfunction on the wire harness side.
Reconnect the G168 driving support ECU assembly connector.
Check for pulses according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
|
*1: w/o Stop and Start System *2: w/ Stop and Start System |
||||
| G168-3 (BZ) - Body ground | LG - Body ground | Skid control buzzer output | Ignition switch ON
Skid control buzzer operating |
0 to 1.5 V |
| Ignition switch ON
Skid control buzzer not operating |
11 to 14 V*1
9.5 to 14 V*2 |
|||
| G168-11 (CA2L) - G168-28 (GND) | LG - BR | CAN communication signal | Ignition switch ON | Pulse generation
(See waveform 1) |
| G168-9 (CA1N) - G168-28 (GND) | W - BR | CAN communication signal | Ignition switch ON | Pulse generation
(See waveform 2) |
| G168-10 (CA2H) - G168-28 (GND) | P - BR | CAN communication signal | Ignition switch ON | Pulse generation
(See waveform 3) |
| G168-8 (CA1P) - G168-28 (GND) | B - BR | CAN communication signal | Ignition switch ON | Pulse generation
(See waveform 4) |
Waveform 1
CAN communication signal
| Item | Content |
|---|---|
| Tester Connection | G168-11 (CA2L) - G168-28 (GND) |
| Tool Setting | 1 V/DIV., 10 μsec./DIV. |
| Condition | Ignition switch ON |
The waveform varies depending on the CAN communication signal.
Waveform 2
CAN communication signal
| Item | Content |
|---|---|
| Tester Connection | G168-9 (CA1N) - G168-28 (GND) |
| Tool Setting | 1 V/DIV., 10 μsec./DIV. |
| Condition | Ignition switch ON |
The waveform varies depending on the CAN communication signal.
Waveform 3
CAN communication signal
| Item | Content |
|---|---|
| Tester Connection | G168-10 (CA2H) - G168-28 (GND) |
| Tool Setting | 1 V/DIV., 10 μsec./DIV. |
| Condition | Ignition switch ON |
The waveform varies depending on the CAN communication signal.
Waveform 4
CAN communication signal
| Item | Content |
|---|---|
| Tester Connection | G168-8 (CA1P) - G168-28 (GND) |
| Tool Setting | 1 V/DIV., 10 μsec./DIV. |
| Condition | Ignition switch ON |
The waveform varies depending on the CAN communication signal.
CHECK MILLIMETER WAVE RADAR SENSOR ASSEMBLY
Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>TERMINALS OF ECU
CHECK FORWARD RECOGNITION CAMERA
Click hereEngine / Hybrid System>CRUISE CONTROL>FORWARD RECOGNITION CAMERA SYSTEM>TERMINALS OF ECU
CHECK BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TERMINALS OF ECU