The driving support ECU assembly uses the millimeter wave radar sensor assembly to detect obstacles in front of the vehicle.
Based on signals from the millimeter wave radar sensor assembly, the driving support ECU assembly calculated the risk of a collision and operates the pre-crash when it determines that the risk is high.
When the millimeter wave radar sensor assembly is replaced with a new one, it acquires the country specification information from the driving support ECU assembly. Also, when the driving support ECU assembly is replaced with a new one, it receives country specification information from the main body ECU (multiplex network body ECU). When country specification information in the millimeter wave radar sensor assembly, driving support ECU and/or main body ECU do not match, DTC C1A0A is stored.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1A0A | Front Radar Sensor Region Code Mismatch | While the ignition switch is ON, the country specification information from the driving support ECU assembly and millimeter wave radar sensor assembly do not match for approximately 2 seconds. | ·
Millimeter wave radar sensor assembly ·
Driving support ECU assembly |
First check the CAN communication system by following How to Proceed with Troubleshooting. After checking that there are no malfunctions in the CAN communication system, proceed with troubleshooting.
Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
When the millimeter wave radar sensor assembly is replaced with a new one, adjustment of the radar sensor beam axis must be performed.
Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT
When replacing the driving support ECU assembly, always replace it with a new one. If a driving support ECU assembly which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle. As a result, a DTC may be stored.
If a millimeter wave radar sensor assembly which was installed to another vehicle is used, the information stored in the driving support ECU assembly and millimeter wave radar sensor assembly will not match and a DTC may be stored.
Clear the DTCs.
Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR
Make sure that the DTC detection conditions are met.
If the detection conditions are not met, the system cannot detect the malfunction.
Check for DTCs.
Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR
DTC C1A0A is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Replace the driving support ECU assembly with a new one.
for LHD: Click hereEngine / Hybrid System>CRUISE CONTROL>DRIVING SUPPORT ECU(for LHD)>REMOVAL
for RHD: Click hereEngine / Hybrid System>CRUISE CONTROL>DRIVING SUPPORT ECU(for RHD)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR
Make sure that the DTC detection conditions are met.
If the detection conditions are not met, the system cannot detect the malfunction.
Check for DTCs.
Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR
DTC C1A0A is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the millimeter wave radar sensor assembly with a new one.
Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>REMOVAL
Adjust the millimeter wave radar sensor assembly.
Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT
| Proceed to |
|---|
| NEXT |
NEXT