The driving support ECU assembly receives accelerator pedal position sensor signals from the ECM to determine if acceleration is being requested by the driver. If the ECM detects a malfunction in the accelerator pedal position sensor, the driving support ECU assembly is notified via CAN communication and stores DTC C1A63.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1A63 | Accelerator Pedal Position Sensor Circuit | While the ignition switch is ON, the driving support ECU assembly receives a throttle sensor malfunction signal from the ECM continuously for approximately 1.3 seconds or more. | ·
SFI system (for Gasoline) ·
ECD system (for Diesel) ·
Driving support ECU assembly |
First check the CAN communication system by following How to Proceed with Troubleshooting. After checking that there are no malfunctions in the CAN communication system, proceed with troubleshooting.
Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
When replacing the driving support ECU assembly, always replace it with a new one. If a driving support ECU assembly which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle. As a result, a DTC may be stored.
Check the vehicle type.
| Result | Proceed to |
|---|---|
| for Gasoline | A |
| for Diesel | B |
A
B
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Check for DTCs.
2AR-FE (w/ Canister Pump Module): Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM(w/ Canister Pump Module)>DTC CHECK / CLEAR
2AR-FE (w/o Canister Pump Module): Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM(w/o Canister Pump Module)>DTC CHECK / CLEAR
3ZR-FAE: Click hereEngine / Hybrid System>3ZR-FAE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR
3ZR-FE (for K111, K111F): Click hereEngine / Hybrid System>3ZR-FE ENGINE CONTROL>SFI SYSTEM(for K111, K111F)>DTC CHECK / CLEAR
3ZR-FE (except K111, K111F): Click hereEngine / Hybrid System>3ZR-FE ENGINE CONTROL>SFI SYSTEM(except K111, K111F)>DTC CHECK / CLEAR
SFI system DTCs are not output.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (2AR-FE [w/ Canister Pump Module]) | B |
| NG (2AR-FE [w/o Canister Pump Module]) | C |
| NG (3ZR-FAE) | D |
| NG (3ZR-FE [for K111, K111F]) | E |
| NG (3ZR-FE [except K111, K111F]) | F |
A
B
C
D
E
F
Clear the DTCs.
Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR
Make sure that the DTC detection conditions are met.
If the detection conditions are not met, the system cannot detect the malfunction.
Check for DTCs.
Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR
DTC C1A63 is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
for LHD: Click hereEngine / Hybrid System>CRUISE CONTROL>DRIVING SUPPORT ECU(for LHD)>REMOVAL
for RHD: Click hereEngine / Hybrid System>CRUISE CONTROL>DRIVING SUPPORT ECU(for RHD)>REMOVAL
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine*1 or Engine and ECT*2 / Trouble Codes.
*1: 2AD-FHV
*2: except 2AD-FHV
2AD-FHV:
Check for DTCs.
Click hereEngine / Hybrid System>2AD-FHV ENGINE CONTROL>ECD SYSTEM>DTC CHECK / CLEAR
except 2AD-FHV:
Check for DTCs.
2AD-FTV: Click hereEngine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>DTC CHECK / CLEAR
2WW: Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>DTC CHECK / CLEAR
ECD system DTCs are not output.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (2AD-FHV) | B |
| NG (2AD-FTV) | C |
| NG (2WW) | D |
A
B
C
Click hereEngine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>DIAGNOSTIC TROUBLE CODE CHART
D