Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › from 2015.10
RM3090E _58 Vehicle Interior _044382 PRE-CRASH SAFETY _0224751 PRE-CRASH SAFETY SYSTEM J

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  Pre-crash Safety System Circuit  


WIRING DIAGRAM

E341243E01
1.115,0.5 2.531,0.729 1.417,0.229 10 false from IG1 NO.1 Relay 3.615,0.708 4.5,0.938 0.885,0.229 10 false ECU-IG NO.2 5.99,0.51 6.188,0.74 0.198,0.229 10 false B 5.76,0.385 5.958,0.573 0.198,0.188 10 false 7 5.698,1.292 5.927,1.479 0.229,0.188 10 false 28 5.969,1.406 6.375,1.615 0.406,0.208 10 false GND 5.75,2.052 6.156,2.26 0.406,0.208 10 false G168 5.76,2.219 7.052,2.76 1.292,0.542 10 false Driving Support ECU Assembly 0.115,2.438 2.271,2.656 2.156,0.219 10 false *2: w/o Stop and Start System 0.115,2.188 2.271,2.406 2.156,0.219 10 false *1: w/ Stop and Start System 2.292,0.219 4.385,0.438 2.094,0.219 10 false from Engine Stop and Start ECU 4.677,0.094 4.854,0.292 0.177,0.198 10 false *1 4.573,0.385 4.75,0.583 0.177,0.198 10 false *2

PROCEDURE

1.CUSTOMER PROBLEM ANALYSIS AND SYMPTOM CHECK
a.

Result:
Proceed to
NEXT



NEXT

2.INSPECT BATTERY VOLTAGE
2.INSPECT BATTERY VOLTAGE
a.

Measure the battery voltage.

Standard voltage:

11 to 14 V



b.

Using the parts location and system diagram, check the system for blown-out fuses, open or short circuits in the wire harness(es) and connectors that are not properly connected by performing a visual check.

HINT:

If the voltage is 11 V or less, replace or recharge the auxiliary battery before proceeding to the next step.



Result:
Proceed to
NEXT



NEXT

3.CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT ECU ASSEMBLY - BATTERY AND BODY GROUND)
3.CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT ECU ASSEMBLY - BATTERY AND BODY GROUND)
a.
E323582C47
1.521,0.167 2.021,0.417 0.5,0.25 0.823,0.333 1.073,0.333 1.073,0.333 1.25,0.948 true 2.938,1.833 2.688,1.833 2.688,1.833 2.469,1.26 true 1.604,0.208 2.219,0.406 0.615,0.198 10 false G168 0.729,0.26 1.01,0.458 0.281,0.198 10 false B 2.99,1.75 3.375,1.906 0.385,0.156 10 false GND 0.052,0.042 0.333,0.24 0.281,0.198 10 false *a
*a Front view of wire harness connector
(to Driving Support ECU Assembly)


Check driving support ECU assembly.

NOTICE:

As the connector may be damaged if a load of more than 10 kg (22 lb) is applied to it, do not apply any more load than necessary to the connector.


i.

Disconnect the driving support ECU assembly connector.


ii.

Measure the voltage according to the value(s) in the table below.

NOTICE:

DTCs may be output when connectors are disconnected during inspection. Therefore, make sure to clear the DTCs using the GTS once the inspection has been completed.


Standard Voltage:
Tester Connection Switch Condition Specified Condition

*1: w/o Stop and Start System

*2: w/ Stop and Start System

G168-7 (B) - Body ground Ignition switch ON 11 to 14 V*1
9.5 to 14 V*2
G168-7 (B) - Body ground Ignition switch off Below 1 V



iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G168-28 (GND) - Body ground Always Below 1 Ω




Result:
Proceed to
OK
NG



OK

4.CHECK CAN COMMUNICATION SYSTEM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK CAN COMMUNICATION SYSTEM
a.

Use the GTS to check if the CAN communication system is functioning normally.

OK:

CAN communication system DTCs are not output.



Result:
Proceed to
OK
NG



OK

5.CHECK FOR DTC

NG

5.CHECK FOR DTC
a.

Check for DTCs and note any codes that are output.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Trouble Codes
50001 220

b.

Clear the DTCs.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Clear DTCs
50002 220

c.

Recheck for DTCs. Try to reproduce the DTCs by duplicating the conditions indicated by the DTCs.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Trouble Codes
50001 220
OK:

DTCs are not output.



Result:
Proceed to
OK
NG



OK

6.DATA LIST / ACTIVE TEST

NG

6.DATA LIST / ACTIVE TEST

b.

Result:
Proceed to
NEXT



NEXT

7.VEHICLE CONTROL HISTORY
7.VEHICLE CONTROL HISTORY
a.

Check whether the vehicle control history (PCS operation history) matches the customer analysis.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>VEHICLE CONTROL HISTORY


Result:
Result Proceed to
Vehicle control history matches the customer analysis A
Vehicle control history does not match customer analysis or there is no vehicle control history B



A

END (EXPLANATION)

B