Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _008749 CRUISE CONTROL _0226194 DYNAMIC RADAR CRUISE CONTROL SYSTEM C

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  C1A4A  Skid Control Buzzer Circuit  


DESCRIPTION

Based on dynamic radar cruise control system operation, the driving support ECU assembly provides warnings to the driver by sounding the skid control buzzer.

DTC C1A4A is stored when a malfunction is detected in the skid control buzzer assembly circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1A4A Skid Control Buzzer Circuit While the vehicle speed is 36 km/h (22 mph) or more and the dynamic radar cruise control system is operating, the driving support ECU assembly detects a malfunction in the skid control buzzer circuit for approximately 0.3 seconds or more.
·

Skid control buzzer

·

Driving support ECU assembly

·

Harness or connector



WIRING DIAGRAM

B403796E46
4.896,2.063 7.052,2.25 2.156,0.188 10 false Driving Support ECU Assembly 3.417,1.167 6.167,1.365 2.75,0.198 10 false Skid Control Buzzer 0.083,0.688 1.417,0.875 1.333,0.188 10 false from IG1 NO. 1 Relay 2.104,0.844 3.792,1.042 1.688,0.198 10 false ECU-IG NO. 2 3.583,0.708 4.042,0.906 0.458,0.198 10 false IG1 5.552,0.708 6.01,0.906 0.458,0.198 10 false BZ 4.219,0.719 4.531,0.917 0.313,0.198 10 false BZ 3.406,1.021 3.865,1.219 0.458,0.198 10 false G74 4.896,1.896 5.354,2.094 0.458,0.198 10 false G168 5.354,0.604 5.51,0.802 0.156,0.198 10 false 3 4.51,0.604 4.667,0.802 0.156,0.198 10 false 1 3.385,0.604 3.542,0.802 0.156,0.198 10 false 2

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When replacing the driving support ECU assembly, always replace it with a new one. If a driving support ECU assembly which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle. As a result, a DTC may be stored.



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (RADAR CRUISE APPROACH ALARM BUZZER)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Radar Cruise2 / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Powertrain > Radar Cruise2 > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Radar Cruise Approach Alarm Buzzer Skid control buzzer assembly (approach sound) ON or OFF Buzzer can be heard
Powertrain > Radar Cruise2 > Active Test
Tester Display
Radar Cruise Approach Alarm Buzzer
50004 197 2
OK:

Skid control buzzer sounds.



Result:
Proceed to
OK
NG



OK

2.CHECK FOR DTCs

NG

3.CHECK TERMINAL VOLTAGE
2.CHECK FOR DTCs
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR

Powertrain > Radar Cruise2 > Clear DTCs
50002 197

d.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.

1.

Turn the ignition switch to ON.

2.

Turn the dynamic radar cruise control system on using the cruise control switch (ON/OFF).

3.

Drive the vehicle at 36 km/h (22 mph) or more for 0.3 seconds or more.




e.

Enter the following menus: Powertrain / Radar Cruise2 / Trouble Codes.


f.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR

Powertrain > Radar Cruise2 > Trouble Codes
50001 197
Result:
Result Proceed to
DTC C1A4A is output A
DTC C1A4A is not output B




A

B

3.CHECK TERMINAL VOLTAGE
a.
B338290C77
0.542,1.198 0.938,1.458 0.396,0.26 2.396,2 2.146,2 2.146,2 1.875,1.604 true 0.063,0.094 0.438,0.271 0.375,0.177 10 false *a 0.615,1.25 1.073,1.417 0.458,0.167 10 false G74 2.458,1.917 2.969,2.104 0.51,0.188 10 false IG1
*a Front view of wire harness connector
(to Skid Control Buzzer)


Disconnect the G74 skid control buzzer connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G74-2 (IG1) - Body ground Ignition switch ON 11 to 14 V
G74-2 (IG1) - Body ground Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

4.INSPECT SKID CONTROL BUZZER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT SKID CONTROL BUZZER


Result:
Result Proceed to
Skid control buzzer is abnormal. A
Skid control buzzer is normal. B



A

5.CHECK HARNESS AND CONNECTOR (SKID CONTROL BUZZER - DRIVING SUPPORT ECU ASSEMBLY)

B

5.CHECK HARNESS AND CONNECTOR (SKID CONTROL BUZZER - DRIVING SUPPORT ECU ASSEMBLY)
a.

Disconnect the G74 skid control buzzer connector.


b.

Disconnect the G168 driving support ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G74-1 (BZ) - G168-3 (BZ) Always Below 1 Ω
G74-1 (BZ) or G168-3 (BZ) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR