Home › Vehicle Interior › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM › from 2015.10
RM3090E _58 Vehicle Interior _008782 DOOR LOCK _0051217 POWER DOOR LOCK CONTROL SYSTEM J

DOOR LOCK  POWER DOOR LOCK CONTROL SYSTEM  Collision Door Lock Release Function does not Operate  


DESCRIPTION

When an impact is detected, a relay inside the door control battery is operated to switch the power source of the door lock with motor assemblies from the vehicle battery to the door control battery.

WIRING DIAGRAM

B439336E01
1.99,0.76 2.302,0.958 0.313,0.198 10 false IG 2.24,0.615 2.552,0.813 0.313,0.198 10 false 8 3.146,0.542 3.458,0.74 0.313,0.198 10 false 50 3.49,0.896 4.427,1.167 0.938,0.271 10 false ECU-IG NO.1 3.135,0.74 3.448,0.938 0.313,0.198 10 false 3B 4.594,0.729 5.51,1.104 0.917,0.375 10 false from IG1 NO.1 Relay 1.76,1.906 2.271,2.104 0.51,0.198 10 false ACTG 2.24,1.771 2.552,1.969 0.313,0.198 10 false 9 3.135,1.885 3.448,2.083 0.313,0.198 10 false 3B 3.135,1.688 3.448,1.885 0.313,0.198 10 false 52 5.438,1.896 5.75,2.094 0.313,0.198 10 false A 5.448,1.698 5.76,1.896 0.313,0.198 10 false 7 5.729,1.885 6.24,2.083 0.51,0.198 10 false ACTG 3.375,2.333 5.01,2.792 1.635,0.458 10 false Instrument Panel Junction Block Assembly 5.302,2.615 6.958,3.063 1.656,0.448 10 false Main Body ECU (Multiplex Network Body ECU) 1.156,2.552 2.479,3.031 1.323,0.479 10 false Door Control Battery 1.156,2.365 1.667,2.563 0.51,0.198 10 false N37

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the main body ECU (multiplex network body ECU), make sure to replace it with a new one.

·

As the door control battery is installed between the vehicle battery and main body ECU (multiplex network body ECU), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (multiplex network body ECU) before performing this troubleshooting procedure.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION



PROCEDURE

1.CHECK DOOR LOCK OPERATION
a.

Check door lock operation.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK

OK:

All doors lock and unlock normally.



Result:
Proceed to
OK
NG



OK

2.CHECK DOOR CONTROL BATTERY (BATTERY VOLTAGE)

NG

2.CHECK DOOR CONTROL BATTERY (BATTERY VOLTAGE)
a.
B377768C22
0.323,0.948 0.823,1.281 0.5,0.333 1.469,1.365 1.323,1.917 1.323,1.917 1.073,1.917 true 0.438,1.031 1.052,1.229 0.615,0.198 10 false N37 0.927,1.854 1.302,2.042 0.375,0.188 10 false IG 0.063,0.042 0.438,0.229 0.375,0.188 10 false *a
*a Front view of wire harness connector
(to Door Control Battery)


Disconnect the door control battery connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
N37-8 (IG) - Body ground Engine switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - DOOR CONTROL BATTERY)

NG

7.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - DOOR CONTROL BATTERY)
3.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - DOOR CONTROL BATTERY)
a.

Disconnect the 3B instrument panel junction block assembly connector.


b.

Disconnect the N37 door control battery connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3B-52 (ACTG) - N37-9 (ACTG) Always Below 1 Ω
3B-52 (ACTG) or N37-9 (ACTG) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

B439338C01
1.885,1.021 2.271,1.229 0.385,0.208 5.417,0.781 5.802,0.99 0.385,0.208 1.135,1.667 1.302,2 1.302,2 1.552,2 true 2.042,1.042 2.198,1.24 0.156,0.198 10 false A 5.521,0.802 5.833,1 0.313,0.198 10 false 3B 1.635,1.927 2.438,2.177 0.802,0.25 10 false ACTG
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
A-7 (ACTG) - 3B-52 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.REPLACE DOOR CONTROL BATTERY

NG

5.REPLACE DOOR CONTROL BATTERY
a.

Replace the door control battery with a new or known good one.

Click hereVehicle Interior>DOOR LOCK>DOOR CONTROL BATTERY>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.CHECK DOOR CONTROL BATTERY
6.CHECK DOOR CONTROL BATTERY
a.

Check door control battery operation.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION

OK:

Collision detection door lock function operates normally.



Result:
Proceed to
OK
NG



OK

END (DOOR CONTROL BATTERY WAS DEFECTIVE)

NG

7.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - DOOR CONTROL BATTERY)
a.

Disconnect the 3B instrument panel junction block assembly connector.


b.

Disconnect the N37 door control battery connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3B-50 - N37-8 (IG) Always Below 1 Ω
3B-50 or N37-8 (IG) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (BATTERY VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (BATTERY VOLTAGE)
a.
B439339C01
1.448,0.188 1.917,0.469 0.469,0.281 0.073,0.042 0.385,0.24 0.313,0.198 10 false *a 1.583,0.25 1.896,0.448 0.313,0.198 10 false 3B
*a Component with harness connected
(Instrument Panel Junction Block Assembly)


Disconnect the instrument panel junction block assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
3B-50 - Body ground Engine switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

GO TO LIGHTING SYSTEM (IG Signal Circuit)