Home › Vehicle Interior › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM › from 2015.10
RM3090E _58 Vehicle Interior _008782 DOOR LOCK _0051217 POWER DOOR LOCK CONTROL SYSTEM J

DOOR LOCK  POWER DOOR LOCK CONTROL SYSTEM  All Doors LOCK/UNLOCK Functions do not Operate Via Door Control Switch or Door Key Cylinder  


DESCRIPTION

The main body ECU (multiplex network body ECU) receives switch signals from the power window regulator master switch assembly, door control switch assembly, driver door key cylinder lock or unlock switch signals from the front door lock assembly RH*1 or front door lock assembly LH*2. The main body ECU (multiplex network body ECU) activates the door lock motor on each door according to these signals.

*1: for RHD

*2: for LHD


WIRING DIAGRAM

B336417E03
5.302,4.854 7.01,5.396 1.708,0.542 10 false Main Body ECU (Multiplex Network Body ECU) 5.281,4.677 5.781,4.854 0.5,0.177 10 false G78 0.969,1.833 4.01,2.094 3.042,0.26 10 false Front Door Lock Assembly LH 0.969,1.677 1.469,1.854 0.5,0.177 10 false J10 1.917,2.917 2.417,3.094 0.5,0.177 10 false UL 1.99,1.219 2.49,1.396 0.5,0.177 10 false L 2.198,0.667 2.698,0.844 0.5,0.177 10 false 10 2.219,1.219 2.719,1.396 0.5,0.177 10 false 9 1.396,0.958 1.896,1.135 0.5,0.177 10 false E 1.188,0.958 1.688,1.135 0.5,0.177 10 false 7 5.74,0.677 6.24,0.854 0.5,0.177 10 false UL3*1 5.76,1.323 6.26,1.5 0.5,0.177 10 false L2 5.313,0.667 5.813,0.844 0.5,0.177 10 false 12*2 5.458,1.219 5.958,1.396 0.5,0.177 10 false 11 5.75,3.01 6.25,3.188 0.5,0.177 10 false UL1 5.771,3.573 6.271,3.75 0.5,0.177 10 false L1 5.448,2.917 5.948,3.094 0.5,0.177 10 false 10 5.51,3.469 6.01,3.646 0.5,0.177 10 false 9 0.865,4.094 2.938,4.479 2.073,0.385 10 false Power Window Regulator Master Switch Assembly 0.854,3.927 1.354,4.104 0.5,0.177 10 false J5 1.969,3.469 2.469,3.646 0.5,0.177 10 false L 1.396,3.198 1.896,3.375 0.5,0.177 10 false E 2.208,2.917 2.708,3.094 0.5,0.177 10 false 9 2.208,3.469 2.708,3.635 0.5,0.167 10 false 2 1.188,3.198 1.688,3.365 0.5,0.167 10 false 1 0.896,6.479 3.063,6.75 2.167,0.271 10 false Door Control Switch Assembly*1 0.896,6.323 1.396,6.5 0.5,0.177 10 false I11 1.917,5.313 2.417,5.49 0.5,0.177 10 false UL 2.219,5.313 2.719,5.479 0.5,0.167 10 false 2 1.396,5.594 1.896,5.771 0.5,0.177 10 false E 1.198,5.594 1.698,5.76 0.5,0.167 10 false 3 2.219,5.865 2.719,6.031 0.5,0.167 10 false 4 1.99,5.854 2.49,6.031 0.5,0.177 10 false L 1.906,0.667 2.406,0.844 0.5,0.177 10 false UL 0.198,0.104 1.667,0.344 1.469,0.24 12 false for LHD: 0.177,7.073 2.583,7.344 2.406,0.271 10 false *1: w/ Door Control Switch Assembly 5.75,0.854 6.25,1.031 0.5,0.177 10 false UL2*2 5.333,0.5 5.833,0.677 0.5,0.177 10 false 24*1 0.188,7.417 2.74,7.698 2.552,0.281 10 false *2: w/o Door Control Switch Assembly

B298281E11
5.313,4.938 5.854,5.208 0.542,0.271 10 G78 5.313,5.094 6.958,5.583 1.646,0.49 10 Main Body ECU (Multiplex Network Body ECU) 0.771,2.146 3.542,2.594 2.771,0.448 10 Front Door Lock Assembly (for Driver Door) 0.781,4.438 2.802,4.917 2.021,0.479 10 Power Window Regulator Master Switch Assembly 1.25,1.344 1.625,1.625 0.375,0.281 10 8 2.229,1.063 2.708,1.417 0.479,0.354 10 5 2.24,1.625 2.781,1.927 0.542,0.302 10 6 5.49,1.625 5.927,1.99 0.438,0.365 10 11 5.49,1.052 5.875,1.344 0.385,0.292 10 12 5.573,3.844 5.896,4.156 0.323,0.313 10 9 5.51,3.302 5.854,3.583 0.344,0.281 10 10 1.958,3.302 2.323,3.604 0.365,0.302 10 UL 2.031,3.865 2.385,4.167 0.354,0.302 10 L 1.438,3.583 1.875,3.875 0.438,0.292 10 E 1.948,1.063 2.292,1.302 0.344,0.24 10 UL 2.021,1.625 2.448,1.958 0.427,0.333 10 L 1.438,1.344 1.833,1.656 0.396,0.313 10 E 5.76,1.708 6.281,2.094 0.521,0.385 10 L2 5.74,1.156 6.26,1.5 0.521,0.344 10 UL2 5.771,3.958 6.281,4.313 0.51,0.354 10 L1 5.75,3.396 6.219,3.688 0.469,0.292 10 UL1 0.781,4.271 1.313,4.542 0.531,0.271 10 I5 0.177,0.073 0.979,0.302 0.802,0.229 12 for RHD: 1.24,3.573 1.521,3.896 0.281,0.323 9 9 2.229,3.281 2.635,3.656 0.406,0.375 10 8 2.24,3.854 2.729,4.229 0.49,0.375 10 2 0.76,1.979 1.292,2.25 0.531,0.271 10 I10

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the main body ECU (multiplex network body ECU), make sure to replace it with a new one.

·

As the door control battery is installed between the vehicle battery and main body ECU (multiplex network body ECU), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (multiplex network body ECU) before performing this troubleshooting procedure.*

*: w/ Door Control Battery

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION



PROCEDURE

1.CHECK DOOR LOCK OPERATION

Result:
Result Proceed to
All doors cannot be locked by power window regulator master switch assembly A
All doors cannot be locked by door control switch assembly (w/ Door Control Switch Assembly) B
All doors cannot be locked by driver door key cylinder C



A

2.READ VALUE USING GTS (Door Lock SW-Lock, Door Lock SW-Unlock)

B

3.READ VALUE USING GTS (Door Lock SW-Lock, Door Lock SW-Unlock)

C

6.READ VALUE USING GTS (Door Key SW-Lock, Door Key SW-Unlock)
2.READ VALUE USING GTS (Door Lock SW-Lock, Door Lock SW-Unlock)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Door Lock SW-Lock Door control switch (power window regulator master switch assembly) lock signal ON or OFF ON: Lock side of door control switch (power window regulator master switch assembly) pushed
OFF: Lock side of door control switch (power window regulator master switch assembly) not pushed
-
Door Lock SW-Unlock Door control switch (power window regulator master switch assembly) unlock signal ON or OFF ON: Unlock side of door control switch (power window regulator master switch assembly) pushed
OFF: Unlock side of door control switch (power window regulator master switch assembly) not pushed
-
Body Electrical > Main Body > Data List
Tester Display
Door Lock SW-Lock
Door Lock SW-Unlock
50003 123 17,18
OK:

The GTS indicates ON or OFF according to the switch operation shown in the table.



Result:
Proceed to
OK
NG



OK

NG

4.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
3.READ VALUE USING GTS (Door Lock SW-Lock, Door Lock SW-Unlock)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the Techstream.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Door Lock SW-Lock Door control switch assembly lock signal ON or OFF ON: Lock side of door control switch assembly pushed
OFF: Lock side of door control switch assembly not pushed
-
Door Lock SW-Unlock Door control switch assembly unlock signal ON or OFF ON: Unlock side of door control switch assembly pushed
OFF: Unlock side of door control switch assembly not pushed
-
Body Electrical > Main Body > Data List
Tester Display
Door Lock SW-Lock
Door Lock SW-Unlock
50003 123 17,18
OK:

The GTS indicates ON or OFF according to the switch operation shown in the table.



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

7.INSPECT DOOR CONTROL SWITCH ASSEMBLY
4.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
a.

for LHD:

i.

Remove the power window regulator master switch assembly.

Click hereVehicle Interior>DOOR LOCK>DOOR CONTROL SWITCH>REMOVAL


ii.

Inspect the power window regulator master switch assembly.

Click hereVehicle Interior>DOOR LOCK>DOOR CONTROL SWITCH>INSPECTION



b.

for RHD:

i.

Remove the power window regulator master switch assembly.

Click hereVehicle Interior>DOOR LOCK>DOOR CONTROL SWITCH>REMOVAL


ii.

Inspect the power window regulator master switch assembly.

Click hereVehicle Interior>DOOR LOCK>DOOR CONTROL SWITCH>INSPECTION



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] AND BODY GROUND)

NG

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] AND BODY GROUND)
a.

for LHD

i.

Disconnect the G78 main body ECU (multiplex network body ECU) connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J5-2 (L) - G78-9 (L1) Always Below 1 Ω
J5-9 (UL) - G78-10 (UL1)
J5-1 (E) - Body ground
J5-2 (L) or G78-9 (L1) - Body ground Always 10 kΩ or higher
J5-9 (UL) or G78-10 (UL1) - Body ground




b.

for RHD

i.

Disconnect the G78 main body ECU (multiplex network body ECU) connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I5-2 (L) - G78-9 (L1) Always Below 1 Ω
I5-8 (UL) - G78-10 (UL1)
I5-9 (E) - Body ground
I5-2 (L) or G78-9 (L1) - Body ground Always 10 kΩ or higher
I5-8 (UL) or G78-10 (UL1) - Body ground




Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.READ VALUE USING GTS (Door Key SW-Lock, Door Key SW-Unlock)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Door Key SW-Lock Driver door key-linked lock/unlock switch lock signal ON or OFF ON: Driver door key cylinder turned to lock position
OFF: Driver door key cylinder not turned to lock position
-
Door Key SW-Unlock Driver door key-linked lock/unlock switch unlock signal ON or OFF ON: Driver door key cylinder turned to unlock position
OFF: Driver door key cylinder not turned to unlock position
-
Body Electrical > Main Body > Data List
Tester Display
Door Key SW-Lock
Door Key SW-Unlock
50003 123 19,20
OK:

The GTS indicates ON or OFF according to the key cylinder operation shown in the table.



Result:
Proceed to
OK
NG



OK

NG

9.INSPECT FRONT DOOR LOCK ASSEMBLY (for Driver Door)
7.INSPECT DOOR CONTROL SWITCH ASSEMBLY
a.

Remove the door control switch assembly.

Click hereVehicle Interior>DOOR LOCK>DOOR CONTROL SWITCH>REMOVAL


b.

Inspect the door control switch assembly.

Click hereVehicle Interior>DOOR LOCK>DOOR CONTROL SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (DOOR CONTROL SWITCH ASSEMBLY - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] AND BODY GROUND)

NG

REPLACE DOOR CONTROL SWITCH ASSEMBLY

8.CHECK HARNESS AND CONNECTOR (DOOR CONTROL SWITCH ASSEMBLY - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] AND BODY GROUND)
a.

Disconnect the G78 main body ECU (multiplex network body ECU) connector.


b.

Disconnect the I11 door control switch assembly connector.


c.

Disconnect the J5 power window regulator master switch assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I11-4 (L) - G78-9 (L1) Always Below 1 Ω
I11-2 (UL) - G78-10 (UL1)
I11-3 (E) - Body ground
I11-4 (L) or G78-9 (L1) - Body ground Always 10 kΩ or higher
I11-2 (UL) or G78-10 (UL1) - Body ground



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT FRONT DOOR LOCK ASSEMBLY (for Driver Door)
a.

for LHD:

i.

Remove the front door lock assembly LH.

Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK>REMOVAL


ii.

Inspect the front door lock assembly LH.

Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK>INSPECTION



b.

for RHD:

i.

Remove the front door lock assembly RH.

Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK>REMOVAL


ii.

Inspect the front door lock assembly RH.

Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK>INSPECTION



Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (FRONT DOOR LOCK ASSEMBLY [for Driver Door] - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] AND BODY GROUND)

NG

REPLACE FRONT DOOR LOCK ASSEMBLY (for Driver Door)

10.CHECK HARNESS AND CONNECTOR (FRONT DOOR LOCK ASSEMBLY [for Driver Door] - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] AND BODY GROUND)
a.

for LHD (w/ Door Control Switch Assembly)

i.

Disconnect the G78 main body ECU (multiplex network body ECU) connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J10-9 (L) - G78-11 (L2) Always Below 1 Ω
J10-10 (UL) - G78-24 (UL3)
J10-7 (E) - Body ground
J10-9 (L) or G78-11 (L2) - Body ground Always 10 kΩ or higher
J10-10 (UL) or G78-24 (UL3) - Body ground




b.

for LHD (w/o Door Control Switch Assembly)

i.

Disconnect the G78 main body ECU (multiplex network body ECU) connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J10-9 (L) - G78-11 (L2) Always Below 1 Ω
J10-10 (UL) - G78-12 (UL2)
J10-7 (E) - Body ground
J10-9 (L) or G78-11 (L2) - Body ground Always 10 kΩ or higher
J10-10 (UL) or G78-12 (UL2) - Body ground




c.

for RHD

i.

Disconnect the G78 main body ECU (multiplex network body ECU) connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I10-6 (L) - G78-11 (L2) Always Below 1 Ω
I10-5 (UL) - G78-12 (UL2)
I10-8 (E) - Body ground
I10-6 (L) or G78-11 (L2) - Body ground Always 10 kΩ or higher
I10-5 (UL) or G78-12 (UL2) - Body ground




Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR