The fuel injectors are located on the intake manifold. They inject fuel into the cylinders based on the signals from the ECM.
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
| *a | Front view of wire harness connector
(to Fuel Injector Assembly) |
Disconnect the fuel injector assembly connectors.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B19-1 - Body ground | Ignition switch ON | 11 to 14 V |
| B17-1 - Body ground | Ignition switch ON | 11 to 14 V |
| B15-1 - Body ground | Ignition switch ON | 11 to 14 V |
| B13-1 - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the fuel injector assembly.
Click hereEngine / Hybrid System>3ZR-FAE FUEL>FUEL INJECTOR>INSPECTION
Perform "Inspection After Repair" after replacing the fuel injector assembly.
Click hereEngine / Hybrid System>3ZR-FAE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the ECM connector.
Disconnect the fuel injector assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B19-2 - B93-98 (#10) | Always | Below 1 Ω |
| B17-2 - B93-95 (#20) | Always | Below 1 Ω |
| B15-2 - B93-96 (#30) | Always | Below 1 Ω |
| B13-2 - B93-97 (#40) | Always | Below 1 Ω |
| B19-2 or B93-98 (#10) - Body ground | Always | 10 kΩ or higher |
| B17-2 or B93-95 (#20) - Body ground | Always | 10 kΩ or higher |
| B15-2 or B93-96 (#30) - Body ground | Always | 10 kΩ or higher |
| B13-2 or B93-97 (#40) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the fuel injector assembly connectors.
Remove the EFI-MAIN NO.2 relay from the engine room relay block and junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B19-1 - 3 (EFI-MAIN NO.2 relay) | Always | Below 1 Ω |
| B17-1 - 3 (EFI-MAIN NO.2 relay) | Always | Below 1 Ω |
| B15-1 - 3 (EFI-MAIN NO.2 relay) | Always | Below 1 Ω |
| B13-1 - 3 (EFI-MAIN NO.2 relay) | Always | Below 1 Ω |
| B19-1 or 3 (EFI-MAIN NO.2 relay) - Body ground | Always | 10 kΩ or higher |
| B17-1 or 3 (EFI-MAIN NO.2 relay) - Body ground | Always | 10 kΩ or higher |
| B15-1 or 3 (EFI-MAIN NO.2 relay) - Body ground | Always | 10 kΩ or higher |
| B13-1 or 3 (EFI-MAIN NO.2 relay) - Body ground | Always | 10 kΩ or higher |
| Result | Proceed to |
|---|---|
| OK
(w/ Stop and Start System) |
A |
| OK
(w/o Stop and Start System) |
B |
| NG | C |
A
B
Click hereEngine / Hybrid System>3ZR-FE ENGINE CONTROL>SFI SYSTEM(except K111, K111F)>ECM Power Source Circuit
C
| *1 | Engine Room Relay Block and Junction Block Assembly |
| *2 | EFI-MAIN NO.2 Relay |
Remove the EFI-MAIN NO.2 relay from the engine room relay block and junction block assembly.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 5 (EFI-MAIN NO.2 relay) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the EFI-MAIN NO.2 relay.
Click hereEngine / Hybrid System>3ZR-FAE ENGINE CONTROL>RELAY>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the EFI-MAIN NO.2 relay from the engine room relay block and junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (EFI-MAIN NO.2 relay) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the EFI-MAIN NO.2 relay and EFI-MAIN NO.1 relay from the engine room relay block and junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2 (EFI-MAIN NO.2 relay) - 3 (EFI-MAIN NO.1 relay) | Always | Below 1 Ω |
| 2 (EFI-MAIN NO.2 relay) or 3 (EFI-MAIN NO.1 relay) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG