Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM › 2015.10–2016.08
RM3090E _53 Suspension _008691 TIRE PRESSURE MONITORING _0048202 TIRE PRESSURE WARNING SYSTEM C

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  C2126/26  Transmitter ID not Received in Main Mode  


DESCRIPTION

After all IDs are registered, DTC C2126/26 is stored in the tire pressure warning ECU and receiver and the tire pressure warning light blinks for 1 minute and then illuminates.

When the tire pressure warning ECU and receiver successfully receives radio waves from all the transmitters whose IDs are stored in the ECU, DTC C2126/26 is cleared and the tire pressure warning light goes off.

DTC No. Detection Item DTC Detection Condition Trouble Area
C2126/26 Transmitter ID not Received in Main Mode After ID registration is completed, ECU does not receive radio waves from transmitters whose IDs are stored in ECU.
·

ID registration failure

·

Tire pressure warning valve and transmitter

·

Tire pressure warning ECU and receiver



NOTICE:

Even when the 2nd set of tires is selected via the ID switching function, (Main) is displayed on the DTC screen for the DTCs.


HINT:

The purpose of this DTC is to help prevent delivering a vehicle that has incorrectly registered IDs. After all IDs are registered, DTC C2126/26 is detected and the tire pressure warning light blinks for 1 minute and then illuminates. If the tire pressure warning light does not turn off after a little while, IDs may be incorrectly registered.


WIRING DIAGRAM

C257450E12
2.823,0.292 4.844,0.677 2.021,0.385 10 false Tire Pressure Warning Valve and Transmitter 2.844,1.583 4.865,1.969 2.021,0.385 10 false Tire Pressure Warning Valve and Transmitter 2.833,2.917 4.854,3.302 2.021,0.385 10 false Tire Pressure Warning Valve and Transmitter*3 0.313,0.906 2.333,1.292 2.021,0.385 10 false Tire Pressure Warning Valve and Transmitter 0.313,2.208 2.333,2.594 2.021,0.385 10 false Tire Pressure Warning Valve and Transmitter 2.271,3.958 3.896,4.365 1.625,0.406 10 false Main Body ECU (Multiplex Network Body ECU) 4.302,3.885 4.708,4.083 0.406,0.198 10 false RDA 4.281,4.323 4.688,4.521 0.406,0.198 10 false PRG 4.729,3.76 4.969,3.938 0.24,0.177 10 false 16 4.771,4.229 5.01,4.406 0.24,0.177 10 false 4 5.76,3.771 6,3.948 0.24,0.177 10 false 4 5.698,6.979 5.938,7.156 0.24,0.177 10 false 12 5.948,3.771 6.615,3.99 0.667,0.219 10 false RDA*1, 5.948,3.979 6.615,4.198 0.667,0.219 10 false RDA2*2 5.948,4.26 6.615,4.479 0.667,0.219 10 false PRG*1, 5.938,4.458 6.604,4.677 0.667,0.219 10 false PRG2*2 2.427,4.875 4.344,5.083 1.917,0.208 10 false Combination Meter Assembly 2.417,5.188 4.323,5.375 1.906,0.188 10 false - Tire Pressure Warning Light 3.052,5.917 3.469,6.073 0.417,0.156 10 false DLC3 5.958,6.531 6.625,6.75 0.667,0.219 10 false CLSW 5.969,7.24 6.635,7.458 0.667,0.219 10 false GND*2 5.76,6.406 6,6.583 0.24,0.177 10 false 3 5.76,4.198 6,4.375 0.24,0.177 10 false 5 1.99,7.104 4.271,7.302 2.281,0.198 10 false Tire Pressure Warning Reset Switch 2,6.917 2.417,7.073 0.417,0.156 10 false G71 3.552,6.427 3.792,6.604 0.24,0.177 10 false 1 2.406,6.438 2.646,6.615 0.24,0.177 10 false 2 0.573,7.354 1.531,7.542 0.958,0.188 10 false : Radio Waves 0.552,7.729 2.833,7.927 2.281,0.198 10 false : CAN Communication Line 0.125,8.063 4.177,8.24 4.052,0.177 10 false *1: for Air Bag Caution Label with "9L" Identification Mark 0.135,8.333 4.667,8.552 4.531,0.219 10 false *2: except Air Bag Caution Label with "9L" Identification Mark 0.156,8.594 2.438,8.792 2.281,0.198 10 false *3: w/ Full Size Spare Tire 5.302,7.854 7.063,8.26 1.76,0.406 10 false Tire Pressure Warning ECU and Receiver 5.313,7.677 6.219,7.854 0.906,0.177 10 false M11*1, M30*2 6,7.031 6.667,7.25 0.667,0.219 10 false E*1, 2.271,3.802 2.729,4 0.458,0.198 10 false G78

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the tire pressure warning ECU and receiver, read the transmitter IDs stored in the old ECU using the GTS and write them down before removal.

·

It is necessary to perform initialization (Click here Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION) after registration (Click here Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION) of the transmitter IDs into the tire pressure warning ECU and receiver if the ECU and/or one of the valve and transmitters has been replaced.



PROCEDURE

1.IDENTIFY TRANSMITTER NOT RECEIVED
a.

Set the tire pressure to the specified values.

Click hereSuspension>TIRE / WHEEL>TIRE AND WHEEL SYSTEM>INSPECTION


b.

Turn the ignition switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Chassis / Tire Pressure Monitor / Data List.


g.

Check the values by referring to the table below.

Chassis > Tire Pressure Monitor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
ID 1 Tire Inflation Pressure ID1 tire inflation pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 488.72 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 388.72kPa (3.9 kgf/cm2, 56 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*
ID 2 Tire Inflation Pressure ID2 tire inflation pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 488.72 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 388.72kPa (3.9 kgf/cm2, 56 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*
ID 3 Tire Inflation Pressure ID3 tire inflation pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 488.72 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 388.72kPa (3.9 kgf/cm2, 56 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*
ID 4 Tire Inflation Pressure ID4 tire inflation pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 488.72 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 388.72kPa (3.9 kgf/cm2, 56 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*
ID 5 Tire Inflation Pressure ID5 tire inflation pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 488.72 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 388.72kPa (3.9 kgf/cm2, 56 psi)
Actual tire inflation pressure
·

If N/A is displayed, data has not been received.*

·

w/ Full Size Spare Tire


HINT:

*: It may take a few minutes until the values are displayed.


Chassis > Tire Pressure Monitor > Data List
Tester Display
ID 1 Tire Inflation Pressure
ID 2 Tire Inflation Pressure
ID 3 Tire Inflation Pressure
ID 4 Tire Inflation Pressure
ID 5 Tire Inflation Pressure
50003 203 36,37,38,39,40

h.

Rapidly reduce the tire pressure for each wheel at least 40 kPa (0.4 kg/cm2, 5.8 psi) within 30 seconds.


i.

Check the Data List.

NOTICE:
·

It may take a few minutes to display the updated tire pressure data.

·

When the "ID Tire Inflation Pressure" data has not changed, reset the tire pressure to the appropriate specified value and rotate the tire 90 to 270 degrees. Then rapidly release the tire pressure and recheck the data.

·

Record the transmitter ID of which "ID Tire Inflation Pressure" data corresponds to each tire.




j.

After confirming that the "ID Tire Inflation Pressure" data for one tire has changed, repeat this procedure one by one. Identify the transmitter that corresponds to the DTC.


Result:
Proceed to
One or more of transmitters abnormal
All normal



One or more of transmitters abnormal

2.CHECK TRANSMITTER ID

All normal

END

2.CHECK TRANSMITTER ID
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / Tire Pressure Monitor / Data List.


f.

Check the values by referring to the table below.

Chassis > Tire Pressure Monitor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Registered ID 1 Code Registered ID1 code min.: 0, max.: FFFFFFF* ID No. registered for transmitter ID1 displayed -
Registered ID 2 Code Registered ID2 code min.: 0, max.: FFFFFFF* ID No. registered for transmitter ID2 displayed -
Registered ID 3 Code Registered ID3 code min.: 0, max.: FFFFFFF* ID No. registered for transmitter ID3 displayed -
Registered ID 4 Code Registered ID4 code min.: 0, max.: FFFFFFF* ID No. registered for transmitter ID4 displayed -
Registered ID 5 Code Registered ID5 code min.: 0, max.: FFFFFFF* ID No. registered for transmitter ID5 displayed w/ Full Size Spare Tire
HINT:

*: Displayed only when the ID No. is not registered.


Chassis > Tire Pressure Monitor > Data List
Tester Display
Registered ID 1 Code
Registered ID 2 Code
Registered ID 3 Code
Registered ID 4 Code
Registered ID 5 Code
50003 203 7,8,9,10,11

g.

Check the ID number on the identified transmitter by removing it from the tire and wheel.

C239103C05
0.463,0.163 0.713,0.386 0.25,0.222 10 *1 6.53,0.612 7.019,0.838 0.49,0.226 10 *2 6.123,1.333 6.375,0.682 6.375,0.682 6.501,0.682 false
*1 Tire pressure warning valve and transmitter *2 Transmitter ID (7-digit number)



h.

Confirm that the ID number on the transmitter and recorded transmitter ID match.

Result:
Proceed to
Match
Do not match




Match

3.REPLACE TIRE PRESSURE WARNING VALVE AND TRANSMITTER

Do not match

4.REGISTRATION OF TRANSMITTER ID
3.REPLACE TIRE PRESSURE WARNING VALVE AND TRANSMITTER
a.

Replace the tire pressure warning valve and transmitter.

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING VALVE>REMOVAL


Result:
Proceed to
NEXT



NEXT

4.REGISTRATION OF TRANSMITTER ID
4.REGISTRATION OF TRANSMITTER ID

Result:
Proceed to
NEXT



NEXT

5.PERFORM INITIALIZATION
5.PERFORM INITIALIZATION

Result:
Proceed to
NEXT



NEXT

6.CONFIRM TIRE INFLATION PRESSURE (DATA LIST)
6.CONFIRM TIRE INFLATION PRESSURE (DATA LIST)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / Tire Pressure Monitor / Data List.


f.

Check the values by referring to the table below.

Chassis > Tire Pressure Monitor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
ID 1 Tire Inflation Pressure ID1 tire inflation pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 488.72 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 388.72kPa (3.9 kgf/cm2, 56 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*
ID 2 Tire Inflation Pressure ID2 tire inflation pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 488.72 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 388.72kPa (3.9 kgf/cm2, 56 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*
ID 3 Tire Inflation Pressure ID3 tire inflation pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 488.72 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 388.72kPa (3.9 kgf/cm2, 56 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*
ID 4 Tire Inflation Pressure ID4 tire inflation pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 488.72 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 388.72kPa (3.9 kgf/cm2, 56 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*
ID 5 Tire Inflation Pressure ID5 tire inflation pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 488.72 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 388.72kPa (3.9 kgf/cm2, 56 psi)
Actual tire inflation pressure
·

If N/A is displayed, data has not been received.*

·

w/ Full Size Spare Tire


HINT:
·

*: It may take a few minutes until the values are displayed.

·

When no "ID Tire Inflation Pressure" data has changed, reset the tire pressure to the appropriate specified value and rotate the tire 90 to 270 degrees. Then rapidly release the tire pressure and recheck the data.



Chassis > Tire Pressure Monitor > Data List
Tester Display
ID 1 Tire Inflation Pressure
ID 2 Tire Inflation Pressure
ID 3 Tire Inflation Pressure
ID 4 Tire Inflation Pressure
ID 5 Tire Inflation Pressure
50003 203 36,37,38,39,40
Result:
Proceed to
Tire pressure values are not displayed.
All tire pressure readings are equal to specified values.




Tire pressure values are not displayed.

REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER

All tire pressure readings are equal to specified values.

END