Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › from 2015.10
RM3090E _59 Vehicle Exterior _008430 LIGHTING (EXT) _0047053 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  ALL Stop Light do not Illuminate  


WIRING DIAGRAM

E341489E01
1.313,0.385 3.146,0.583 1.833,0.198 10 false from Battery 1.573,1.25 2.188,1.448 0.615,0.198 10 false STOP 0.854,1.594 1.396,1.802 0.542,0.208 10 false to ECM 2.5,2.74 4.333,3 1.833,0.26 10 false Stop Light Switch Assembly 2.51,2.573 2.969,2.771 0.458,0.198 10 false A77 2.948,2.021 3.406,2.219 0.458,0.198 10 false GND 2.958,1.573 3.115,1.771 0.156,0.198 10 false L 3.51,2.021 3.969,2.219 0.458,0.198 10 false OUT 2.948,1.094 3.406,1.292 0.458,0.198 10 false B 3.49,1.083 3.948,1.281 0.458,0.198 10 false ACC 2.729,0.948 2.885,1.146 0.156,0.198 10 false 6 2.719,1.906 2.875,2.104 0.156,0.198 10 false 2 2.719,1.458 2.875,1.656 0.156,0.198 10 false 5 3.896,0.969 4.052,1.167 0.156,0.198 10 false 4 3.906,1.896 4.063,2.094 0.156,0.198 10 false 1 5.49,0.948 5.802,1.146 0.313,0.198 10 false 26 5.792,1.073 6.406,1.271 0.615,0.198 10 false STPO 5.521,1.896 5.833,2.094 0.313,0.198 10 false 35 5.781,2.021 6.396,2.219 0.615,0.198 10 false STP 5.458,2.625 5.917,2.823 0.458,0.198 10 false A80 5.448,2.802 7.083,3.167 1.635,0.365 10 false Brake Actuator Assembly (Skid Control ECU) 3.906,3.708 4.063,3.906 0.156,0.198 10 false B 3.917,5.458 4.073,5.656 0.156,0.198 10 false B 3.906,7.281 4.063,7.479 0.156,0.198 10 false B 2.396,3.708 2.552,3.906 0.156,0.198 10 false E 2.396,5.458 2.552,5.656 0.156,0.198 10 false E 2.385,7.292 2.542,7.49 0.156,0.198 10 false E 4.115,3.708 4.271,3.906 0.156,0.198 10 false 1 4.115,5.458 4.271,5.656 0.156,0.198 10 false 1 2.219,7.292 2.375,7.49 0.156,0.198 10 false 1 2.208,3.708 2.365,3.906 0.156,0.198 10 false 4 2.208,5.458 2.365,5.656 0.156,0.198 10 false 4 4.125,7.281 4.281,7.479 0.156,0.198 10 false 2 1.875,4.604 2.333,4.802 0.458,0.198 10 false M13 3.094,4.01 3.708,4.208 0.615,0.198 10 false Stop 3.063,5.771 3.677,5.969 0.615,0.198 10 false Stop 1.875,4.802 4.563,5.031 2.688,0.229 10 false Rear Combination Light Lens and Body LH 1.875,6.354 2.333,6.552 0.458,0.198 10 false M19 1.885,6.531 4.573,6.76 2.688,0.229 10 false Rear Combination Light Lens and Body RH 2.385,8.135 4.167,8.375 1.781,0.24 10 false Center Stop Light Assembly 2.406,7.958 2.865,8.156 0.458,0.198 10 false U1

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the brake actuator assembly (skid control ECU), perform zero point calibration.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION

·

When the smart entry start function does not operate, check the entry and start system (start function)*.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING


*: w/ Entry and Start System



PROCEDURE

1.CHECK STOP LIGHT OPERATION
a.

Check that the stop lights illuminate when the brakepedal is depressed.

OK:

The stop lights illuminate when the brake pedal isdepressed.



Result:
Proceed to
OK
NG



OK

CHECK CONNECTOR CONNECTION CONDITION

NG

2.CHECK HARNESS AND CONNECTOR (OUT)
2.CHECK HARNESS AND CONNECTOR (OUT)
a.

Disconnect the A80 brake acyuator assembly.


b.

Disconnect the A77 stoplight light switch assembly connector.


c.

Disconnect the M13 rear combination light lens and body LH connector.


d.

Disconnect the M19 rear combination light lens and body RH connector.


e.

Disconnect the U1 center stop light assembly connector.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A80-35 (STP) - A77-1 (OUT) Always Below 1 Ω
A80-35 (STP) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK STOP LIGHT SWITCH ASSEMBLY (OUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK STOP LIGHT SWITCH ASSEMBLY (OUT)
a.

Disconnect the M13 rear combination light lens and body LH connector.


b.

Disconnect the M19 rear combination light lens and body RH connector.


c.

Disconnect the U1 center stop light assembly connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A77-1 (OUT) - Body ground Brake pedal depressed 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE REAR COMINATION LIGHT LENS AND BODY AND CENTER STOP LIGHT ASSEMBLY
a.

Inspect the rear combination light lens and body.

Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY>INSPECTION


b.

Inspect the center stop light assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>HIGH MOUNTED STOP LIGHT ASSEMBLY>INSPECTION



NG

REPLACE STOP LIGHT SWITCH ASSEMBLY