Home › Vehicle Exterior › WIPER / WASHER › WASHER MOTOR › from 2015.10
RM3090E _59 Vehicle Exterior _008795 WIPER / WASHER _0050088 WASHER MOTOR A

WIPER / WASHER  WASHER MOTOR  INSTALLATION  


PROCEDURE

Hide 85942 1.INSTALL HEADLIGHT CLEANER CONTROL RELAY (w/ Headlight Cleaner System)

E268378

a.

Attach the claw to install the headlight cleaner control relay.


Hide 85280A 2.INSTALL HEADLIGHT CLEANER MOTOR AND PUMP ASSEMBLY (w/ Headlight Cleaner System)

E268379

a.

Install the headlight cleaner motor and pump.


Hide 85397 3.INSTALL LEVEL WARNING SWITCH ASSEMBLY

a.

Install the level warning switch assembly.


Hide 85330 4.INSTALL WINDSHIELD WASHER JAR ASSEMBLY

a.

w/ Headlight Cleaner System:

i.

Attach the guide to install the windshield washer jar assembly with the 3 bolts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)

E268374C01
6.26,0.896 6.469,0.656 true 6.51,0.542 6.76,0.75 0.25,0.208 10 true *a
*a Guid - -



ii.

Connect the 3 connectors.


iii.

Attach the 6 clamps



b.

w/o Headlight Cleaner System:

i.

Attach the guide to install the windshield washer jar assembly with the 3 bolts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)

B427694C01
6.333,0.792 6.552,0.552 true 6.563,0.427 6.781,0.635 0.219,0.208 10 true *a
*a Guid - -
V100135

Bolt
V100136

Connector



ii.

Connect the connector.


iii.

Attach the 6 clamps



Hide 85301 5.INSTALL WASHER INLET SUB-ASSEMBLY

a.
E268381

Install the washer inlet to the windshield washer jar and pump assembly.


b.

Install the clip.


Hide 52119A 6.INSTALL FRONT BUMPER COVER

Hide 85310 7.INSTALL WINDSHIELD WASHER MOTOR AND PUMP ASSEMBLY

a.
E268382

Install the windshield washer motor and pump assembly to the packing of the windshield washer jar assembly.


b.

Connect the connector.


Hide 8.FILL UP WINDSHIELD WASHER JAR AND PUMP ASSEMBLY WITH WASHER FLUID

E268383

a.

Connect the 2 washer hoses to the windshield washer motor and pump, and fill the washer jar with washer fluid.


Hide 53875A 9.INSTALL FRONT FENDER LINER RH

a.
B427878

Install the front fender liner RH with the 6 clips.


b.
B427879

Install the new 4 grommets.


c.
B427876

Install the 2 screws.


d.
B427952C01
3.115,0.167 3.427,0.323 0.313,0.156 10 false *a 3.115,0.833 3.427,0.99 0.313,0.156 10 false *b
*a Correct
*b Incorrect


Install the pin hold clip and screw.

HINT:

Insert the pin hold clip with the slot aligned vertically. Do not rotate the clip after inserting it. After installation, confirm that the slot is vertical.



Hide 53895B 10.INSTALL FRONT FENDER FRONT SPLASH SHIELD RH

HINT:

Use the same procedure described for the LH side.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>FRONT BUMPER>INSTALLATION